Related Manuals for Husqvarna 45-04292-669
Summary of Contents for Husqvarna 45-04292-669
- Page 1 OPERATOR'S MANUAL 48" SNOW BLADE Model Number 45-04292-669 Husqvarna 546 07 98-01 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY PRINTED IN U.S.A. FORM NO. 28052 (03/03/25)
-
Page 2: Safety Rules
SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. CAUTION: VEHICLE BRAKING AND LOOK FOR THIS SYMBOL TO POINT OUT STABILITY MAY BE AFFECTED WITH THE IMPORTANT SAFETY PRECAUTIONS. - Page 3 PARTS IN PACKAGES NOT SHOWN FULL SIZE REF QTY DESCRIPTION REF QTY DESCRIPTION Cable End Fitting Plastic Grip Blade Pivot Shaft Channel Pivot Pin Nylon Tie Grip Assembly Blade Adjust Spring Skid Shoe (HARDWARE SHOWN FULL SIZE) SPECIAL USE ONLY REF.
-
Page 4: Section 1: Assembly Instructions
INSTRUCTIONS FOR TRACTORS WITH A SECTION 1: SINGLE SUSPENSION BRACKET ASSEMBLY INSTRUCTIONS 3. Remove the tractor hood. Refer to your tractor owners manual for instructions on how to properly remove the hood. TOOLS REQUIRED FOR ASSEMBLY (1) Pliers 4. Remove the browning shield from the front of the tractor (1) Hammer as shown. - Page 5 (E), a large 1/2" washer (L) if needed, and a 5/16" nylock nut (J). If the tractor is a Husqvarna TS200 Series with dual pedal there will be a bracket like the one drawn with dotted lines in figure 3b. In the front three holes use three 3/8"...
- Page 6 9. Attach the R.H. hanger bracket to the two front empty 13. Attach the R.H. hanger bracket to the three holes shown on holes on the right side of the tractor frame using two the side of the tractor frame using three 3/8" x 1" hex bolts new 3/8"...
- Page 7 22. Assemble one 5/16" jam nut (H) approximately 3/4" onto 19. Attach the R.H. hanger bracket to the front two holes in threaded end of control cable that has no rubber cap or the right side of the tractor frame using a new 3/8" x 1" preassembled nuts.
- Page 8 26. To attach the blade to the channel assembly, align the notched holes in the pivot plate with the notched holes 28. Assemble the 1/2" washer (P) onto the channel pivot in the blade. Insert a 1/8" x 1-1/4" cotter pin (O) down pin.
- Page 9 32. Remove the rubber cap and the first jam nut from the threaded end of the control cable and slide them onto 36. Place the end of the blade pivot rod down through the the control cable wire. Adjust the second jam nut on the blade pivot shaft.
-
Page 10: Section 2: Operating The Blade
USING THE SNOW BLADE SECTION 2: OPERATING THE BLADE 3. Prepare the lawn tractor engine for cold weather using instructions furnished with the lawn tractor. 1. To raise the blade, use the handle grip located on the 4. Always begin with the transmission in first (low) gear end of the handle tube. -
Page 11: Section 3: Maintenance
SECTION 3: SECTION 5: MAINTENANCE STORING THE BLADE Recommendations When Storing 1. During the operating season, check all bolts, nuts and 1. When the snow blade is not being used, remove all dirt hairpin cotters to be sure they are secure. and rust and touch up with paint. - Page 14 BROWNING SHIELD If your Husqvarna TS200 Series tractor is equipped with lower dash covers as shown below, it will be necessary to remove them in order to mount this attachment. (Does not apply for front mount dethatchers). Refer to your tractor manual for removal instructions.
- Page 15 NOTES...
- Page 16 À DÉPOSER À DÉPOSER EN MAGASIN EN DÉCHÈTERIE Cet appareil se recycle Points de collecte sur www.quefairedemesdechets.fr Privilégiez la réparation ou le don de votre appareil ! 114 46 88-38...
Need help?
Do you have a question about the 45-04292-669 and is the answer not in the manual?
Questions and answers