Husqvarna 45-0636-669 Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Snow Blower
  5. 45-0636-669
  6. Operator's manual
Husqvarna 45-0636-669 Operator's Manual

Husqvarna 45-0636-669 Operator's Manual

48" snow blade
Hide thumbs

Advertisement

Table of Contents

OPERATOR'S MANUAL
48" SNOW BLADE
Model Number
45-0636-669
Husqvarna
547 53 77-01
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
FORM NO. 3-415 (03/03/25)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 45-0636-669 and is the answer not in the manual?

Questions and answers

Related Manuals for Husqvarna 45-0636-669

Summary of Contents for Husqvarna 45-0636-669

  • Page 1 OPERATOR'S MANUAL 48" SNOW BLADE Model Number 45-0636-669 Husqvarna 547 53 77-01 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY FORM NO. 3-415 (03/03/25)

  • Page 2: Safety Rules

    SAFETY RULES Remember, any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times when using power equipment. CAUTION: VEHICLE BRAKING AND LOOK FOR THIS SYMBOL TO POINT OUT STABILITY MAY BE AFFECTED WITH THE IMPORTANT SAFETY PRECAUTIONS.
  • Page 3 PARTS IN PACKAGES REF QTY DESCRIPTION REF QTY DESCRIPTION Hex Bolt, 3/8 x 3-1/2" Blade Pivot Shaft Release Grip Assembly 3/8" Hex Nut Skid Shoe Trip Spring Grip Plastic Grip HARDWARE REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION Channel Pivot Pin Spacer, 5/8"...

  • Page 4: Tools Required For Assembly

    STEP 2: ASSEMBLY INSTRUCTIONS Attach the R.H. hanger bracket (2) to the front four holes in the right side of the tractor frame using TOOLS REQUIRED FOR ASSEMBLY an M8 hex bolt (R), 5/16" lock washer (Q), and 5/16" washer (M) as shown in figure 2. Repeat step for the (1) Pliers L.H.
  • Page 5 STEP 4: STEP 6: Center the channel sub assembly (4) between Install one 5/16" jam nut (H) approximately 3/4" the tabs on the back of the blade assembly (5). onto the threaded end of the control cable that has no •...
  • Page 6 STEP 7: STEP 9: Assemble the 1/2" washer (P) onto the chan- Remove the rubber cap and the first jam nut from nel pivot pin (K). See figure 7. the threaded end of the control cable and slide them • Attach the channel assembly to the tractor by placing onto the control cable wire.
  • Page 7 STEP 11: Place the end of the blade pivot rod (6) down through the blade pivot shaft (11). Attach the other end of the blade pivot rod (6) to the lift handle tube (7). Se- cure both ends with a hairpin cotter (N). See figure 11. •...

  • Page 8: Section 2: Operating The Blade

    USING THE SNOW BLADE SECTION 2: OPERATING THE BLADE 3. Prepare the lawn tractor engine for cold weather using instructions furnished with the lawn tractor. 1. To raise the blade, use the handle grip located on the 4. Always begin with the transmission in first (low) gear end of the handle tube.

  • Page 9: Section 3: Maintenance

    SECTION 3: SECTION 5: MAINTENANCE STORING THE BLADE Recommendations When Storing 1. During the operating season, check all bolts, nuts and 1. Keep the snow blade clean when not in use. hairpin cotters to be sure they are secure. 2. Touch up bare metal with paint or apply a light coat of 2.
  • Page 12 À DÉPOSER À DÉPOSER EN MAGASIN EN DÉCHÈTERIE Cet appareil se recycle Points de collecte sur www.quefairedemesdechets.fr Privilégiez la réparation ou le don de votre appareil ! 114 46 89-38...

Table of Contents