Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Anton/Bauer SPS-150
Summary of Contents for Anton/Bauer SPS-150
- Page 1 Approved Copy ® SPS-150 Power Supply A7595-0351 Rev B...
-
Page 2: Table Of Contents
Approved Copy TABLE OF CONTENTS INTRODUCTION FEATURES SAFEGUARDS GROUNDING/EARTHING FCC NOTICE OPERATION AS AN ON-CAMERA POWER SUPPLY OPERATION AS A STAND ALONE POWER SUPPLY SPECIFICATIONS FUSE/TYPE REPLACEMENT SERVICE LIMITED WARRANTY... -
Page 3: Introduction
Approved Copy INTRODUCTION The SPS-150 is a 150W snap-on power supply which has (2) two 4pin XLR auxiliary outputs. The 150w power supply is designed to meet the high power needs of today’s video cameras. Mounting to any Anton/Bauer Gold Mount , power is automatically supplied to the camera, without ® the need of an ON/OFF switch. Also designed as a stand alone power supply, the SPS-150 has (2) two 4p XLR outputs, and can be placed wherever is convenient. Please read all instructions before operating this unit. FEATURES SAFEGUARDS • 150w power supply Power Sources: This unit was designed to operate at mains voltages from 100 to 240vac, 50/60Hz. • (2) Two 4pin XLR connectors for auxiliary 15v outputs Risk of Electrical Shock: Refer servicing to qualified service • Wide range input (100-240VAC 50/60Hz) personnel. TO PREVENT FIRE OR SHOCK HAZARD, DO NOT •... -
Page 4: Operation As An On-Camera Power Supply
Approved Copy OPERATION AS AN OPERATION AS A STAND ALONE ON-CAMERA POWER SUPPLY POWER SUPPLY The SPS-150 is designed as a 150w on-camera power supply, which The SPS-150 can be used to power virtually all professional video meets the needs of today’s video cameras and accessories. equipment and accessories that can be powered from a 15v dc source. Simply snap the SPS-150 on the Gold Mount of the camera. Be ® sure to align the t-studs of the power supply to the Gold Mount . A Simply plug one end of an XLR-4 cable (available separately) or any ® solid “click” ensures that the unit is securely attached to the camera. standard 4pin XLR cable into the SPS-150 and the other end into the Power is automatically supplied to the unit, without the need of a piece of equipment being powered. (Please be sure to observe proper switch. polarity to avoid damaging any equipment). A right angle IEC power cable is supplied for a clean dressing on the A second and third piece of equipment can be powered via the sec- camera. ond 4pin XLR output or snap-on mount. Be sure not to exceed a total of 150 watts (10 amps) or else the resettable breaker will trip. If this This power supply has (2) two auxiliary 4pin XLR outputs which happens, remove all equipment being powered, unplug unit, and then provides the ability to power other on-camera accessories such as plug back in again. -
Page 5: Fuse/Type Replacement
Approved Copy FUSE/TYPE REPLACEMENT The SPS-150 does not have a fuse to be replaced in the case that the unit is shorted or is overloaded. A resettable circuit breaker is located in the unit and will “trip” when shorted or overloaded. If this should occur, simply remove all pieces of equipment which are being powered, unplug unit, and then plug back in again. SERVICE In the event the SPS-150 power supply fails to deliver acceptable performance it must be returned to the Anton/Bauer Service Department. Only the Anton/Bauer Service Department is equipped to service the SPS-150 power supply and calibrate the electronic components and sen- sors. Any attempt by the user or any other unauthorized persons to service this power supply will surely result in improper calibration which could result in severe damage or safety hazards. Therefore: 1. DO NOT ATTEMPT TO SERVICE THIS POWER SUPPLY UNDER ANY CIRCUMSTANCE. 2. DO NOT SEND THIS POWER SUPPLY FOR SERVICE TO ANYONE OTHER THAN Anton/Bauer SERVICE DEPARTMENT. -
Page 6: Limited Warranty
Anton/Bauer. Anton/Bauer only authorizes the use of original Anton/Bauer product with this product. The liability of Anton/Bauer hereunder is expressly limited to a claim for Use only original Anton/Bauer equipment with this product. repair or replacement of the Product or as otherwise stated herein at Anton/Bauer’s sole discretion. Notice of any claim under this warranty shall be delivered to Anton/Bauer during the period of the warranty and the Product shall be returned with its packaging promptly, at your expense, to an Anton/Bauer Customer Support Center or to the address above. Upon receipt of the Product and a record of your compliance with the conditions of this warranty, Anton/Bauer will repair or replace the Product and return it to you, or issue a credit, as applicable. You are responsible for all shipping and handling charges to and from authorized facility. - Page 7 Approved Copy The following are trademarks of Anton/Bauer, Inc.: Anton/Bauer, Anton/Bauer logo and parallelogram design, Aspekt, Automatique, DataTap, DIONIC, Elipz, Egripz, Elightz, Essentialz, Gold Mount, HubZ, HyTRON, Impac, Interactive and design, LifeSaver, Logic Series, Logic Series Logo, Maxx man logo design, Nexus, PowerStrap, Proformer, Probe, ProPac, RealTime, Satellight, Snap-On, Stasis, Stasis Flex, Tandem, TrimPac, Ultrakit, Ultralight, “One World.
Need help?
Do you have a question about the SPS-150 and is the answer not in the manual?
Questions and answers