HPE 670 Series, AP-674, AP-675, AP-677, AP-679 Manual

About This Guide

This document describes the hardware features of the HPE Aruba Networking 670 Series Outdoor Access Points. It provides a detailed overview of the physical and performance characteristics of each access point model and explains how to install the access point.

Guide Overview

• Hardware Overview provides a detailed hardware overview of the HPE Aruba Networking 670 Series Outdoor Access Points.
• Installation describes how to install the HPE Aruba Networking 670 Series Outdoor Access Points.
• Specifications, Safety, and Compliance lists the HPE Aruba Networking 670 Series Outdoor Access Points technical specifications, safety, and regulatory compliance information.

Related Documentation

You require the following documents for the complete management of HPE Aruba Networking 670 Series Outdoor Access Points.

• CLI bank: https://www.arubanetworks.com/techdocs/CLI-Bank/Content/Home.htm

Contacting Support

Table 1: Contact Information

Hardware Overview

The HPE Aruba Networking 670 Series Outdoor Access Points support the IEEE 802.11ax (Wi-Fi 6E) WLAN standard, while also supporting IEEE 802.11a/b/g/n/ac wireless services.

Package Contents

Inform your supplier to check if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

Table 2: Package Contents

Tools Required

• Philips screwdriver (#2 for M4 x 6 screw)
• Flat blade screwdriver (for Ethernet port cap)
• 8mm Allen or hex key (for USB console cap)

Access Point Views

Figure 1 AP-674 Front View (with Aesthetic Cover)

The antenna connectors of the AP-674 are covered by an aesthetic cover. The aesthetic cover can be removed when necessary. If leaving the cover in place, be careful not to exceed the antenna cable bend radius, or use proper angled connector cables to minimize cable bends.

Figure 2 AP-674 Back View (with Aesthetic Cover)

1. E0 Port (PoE-In)
2. USB-A Interface
3. Grounding Point
4. USB-C Interface
5. E1 Port (SFP)
6. USB-C Console Port, Reset Button, and LED

Figure 3 AP-675 Front View

Figure 4 AP-675 Back View

1. E0 Port (PoE-In)
2. USB-A Interface
3. Grounding Point
4. USB-C Interface
5. E1 Port (SFP)
6. USB-C Console Port, Reset Button, and LED

Figure 5 AP-677/AP-679 Front View

Figure 6 AP-677/AP-679 Back View

1. E0 Port (PoE-In)
2. USB-A Interface
3. Grounding Point
4. USB-C Interface
5. E1 Port (SFP)
6. USB-C Console Port, Reset Button, and LED

The AP-677 and AP-679 are the same in physical appearance. They have different antenna patterns. For details on the antenna patterns, refer to the 670 Series data sheet.

External Antenna Connectors

The AP-674 access point has four Nf connectors for external Wi-Fi antennas, one Nf connector for external BLE antenna, and one Nf connector for external GNSS antenna.

Figure 7 AP-674 Bottom View (without Aesthetic Cover)

External antennas for this device must be installed by a professional installer, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. A list of approved antennas can be found in the ordering guide at https://www.arubanetworks.com
The AP-674 access point is shipped with a GNSS antenna, a mount bracket for the antenna, a RF cable, and a hose clamp. To install the GNSS antenna on a wall or to a pole, refer to the AP-ANT-OUT-GPS Antenna Installation Guide.
When a new or factory defaulted AP-674 access point is powered up for the first time, and the AP-674 is using an external antenna with Smart Antenna Module (SAM) enabled that does not support 2.4 GHz, the manufacturing image upgrade and provisioning of the AP-674 can only be done via Ethernet connection. If the AP-674 uses the external antennas without the SAM module, the manufacturing image upgrade can be done via Ethernet or 2.4 GHz connection, so long as there is a compatible 2.4 GHz supported antenna is used.

LED

The 670 Series access point is equipped with one LED that indicates the system status of the access point.

Table 3: LED Meanings during Boot Up

1. Mostly off (off 6 seconds, then one blink flash).
2. Equally off/on (off 1 second, then red 1 second).

Table 4: LED Meanings during Operation

Reset Button

The reset button can be used to reset the AP to default settings, or turn off/on the LED.

• To reset the AP to default settings, hold down the reset button for several seconds while the AP is being powered on, or for more than 10 seconds during normal operation.
• To turn off or on the LED, press the reset button for less than 10 seconds during normal operation.

USB-C Console Port

Use the included USB Type-C console cable to connect the access point to a laptop or a serial terminal for direct management.
You need an 8mm allen or hex key to remove the console port cap.

Ethernet Ports

The access point has two Ethernet ports:

• E0 port: 100/1000/2500Base-T auto-sensing MDI/MDI-X wired network port (RJ45). The E0 port supports PoE-in, allowing the AP to draw power from an 802.3at (Class 4) or 802.3bt (Class 6) PoE power source.
• E1 port: SFP port.

Grounding Point

Always remember to protect the access point by installing the grounding line first before connecting to a network and applying power. Additionally, if removing or taking down the AP, the grounding line should be the last item disconnected.

USB 2.0 Host Interfaces

The 670 Series access point has two USB host interfaces:
USB-A interface: capable of sourcing up to 1A/5W to an attached device.
USB-C interface: capable of sourcing up to 2A/10W to an attached device.

BLE Radio Default State

When the access point is in factory default state the integrated BLE radio is enabled. This applies to the non-TAA product SKUs only. On the TAA products, the BLE radio is disabled when the unit is in factory default conditions. Once the AP has established a connection with its management platform, the BLE radio state is updated to match what's configured there. This state is maintained if the AP is powercycled or rebooted.

Console Port Default State

When the access point is in factory default state the console interface (both physical port and BLE) is enabled with default credentials (username is "admin" and password is the serial number of the unit). Once the AP has established a connection with its management platform, the console port state (enabled/disabled) and access credentials are updated to match what's configured there. State and credentials are maintained if the AP is power-cycled or rebooted.

USB Host Interface Default State

When the access point is in factory default state the USB host interface is powered and enabled, assuming the AP is not in a restricted power mode. On some AP models the USB port may be disabled when a POE source with insufficient power budget is used. Once the AP has established a connection with its management platform, the USB host interface state is updated to match what's configured there. This state is maintained if the AP is power-cycled or rebooted.

Installation

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-Installation Checklist
Before installing the access point, be sure that you have the following:

• A mount kit compatible with the AP and mount surface
• A STP or shielded Ethernet cable with network access
• Compatible mounting bracket (see HPE Aruba Networking 670 Series Outdoor Access Points Ordering Guide for more) n Compatible antennas (AP-674 only)

Some optional items:

• A compatible PoE midspan injector with power cord
  Also, make sure at least one of the following network services is supported:
• HPE Aruba Networking Discovery Protocol (ADP)
• DNS server with an "A" record
• DHCP Server with vendor specific options

Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used.

Outdoor Planning and Deployment Considerations

Prior to deploying an outdoor wireless network, the environment must be evaluated to plan for a successful WLAN deployment. Successfully evaluating the environment enables the proper selection of access points and antennas and assists in the determination of their placement for optimal RF coverage.
The rules for the 5600-5650 MHz band vary by region.

Identifying Specific Installation Locations

Use the intended RF design provided by the professionals. Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in RF plan.

Identifying Known RF Absorbers/Reflectors/ Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach an access point to its fixed location. RF absorbers include:

• Cement/concrete—Old concrete has high levels of water dissipation, which dries out the concrete, allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals.
• Natural Items—Fish tanks, water fountains, ponds, and trees
• Brick

RF reflectors include:

• Metal Objects—Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets.
• Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances.

RF interference sources include:

• Other Wi-Fi networks
• Microwave ovens
• Bluetooth devices

Access Point Installation

The 670 Series access point can be installed on a wall or a pole by using a compatible mount kit. HPE Aruba Networking provides several mount kits to use with the 670 Series access point. These mount kits are available as accessories and must be ordered separately.

Table 5: Mount Kits for 670 Series Access Point

All HPE Aruba Networking access points should be professionally installed by a professional installer. The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Failure to properly install this product may result in physical injury and/or damage to property.

This 670 Series access point is intended for installation in a RESTRICTED ACCESS LOCATION attached to a pole or installed on a wall. Installers should disconnect power before working with or near the access point.

Grounding Access Point

Grounding the access point must be completed before powering up the AP. The ground wire should be #8 AWG.

1. Strip the insulating jacket off of one end of the ground wire and place the bare conductor into the ground lug (included in the package), then crimp the connection by pressing firmly with the crimping pliers.
2. Fasten the ground lug to the grounding point on the access point with the screw included in the package.

Connecting Ethernet Cable

To connect an Ethernet cable to the access point, perform the following steps using the M20 cable gland.

Failure to use the included Ethernet cable gland can lead to connectivity and PoE issues.
The Ethernet cable is not included and must be purchased separately. Purchase a suitable UV-resistant, outdoor rated, CAT 5E or better shielded cable for use with the access point.

1. Remove the dust cap from the Ethernet port.
2. Slide the sealing nut, clip, seals, gland body, and O-ring over the cable.
3. Insert the RJ45 connector to the Ethernet port on the AP.
4. Place the O-ring on the gland body, and ensure it is in place.
5. Thread the gland body into the Ethernet port, and tighten to a torque of 8.9 in/lbs (1.0 Nm).
6. Combine the two split seals over the cable, and place them on the gland body.
7. Move the clip towards the gland body, passing over the seals, until the clip properly fits into the gland body.
8. Tighten the sealing nut onto the gland body to a torque of 8.9 in/lbs (1.0 Nm).
9. Connect the other end of the Ethernet cable to a PoE port of a compliant PoE Injector or PoE switch.

Figure 8 Ethernet Cable and M20 Cable Gland Assembly

1. Ethernet Cable
2. O-ring
3. Gland Body
4. Seals
5. Clip
6. Sealing Nut

Two sets of seals are provided in the package for use with the Ethernet cables. One is applicable for cables with 4-6 mm diameter, and the other is applicable for cables with 6-10 mm diameter.

Figure 9 Ethernet Cable and M20 Cable Gland installed to AP

Connecting Fiber-optic Cable

The fiber-optic cable is not included in the package and must be purchased separately. Purchase a suitable 612 mm diameter, UV-resistant, outdoor rated cable for use with the access point.
To connect a fiber-optic cable to the access point, an SFP transceiver module and a CKIT-OD-SFP outdoor SFP weathertight strain relief kit are required. They are not included in the package and must be purchased separately. Refer to the ordering guide of the 670 Series access point for details. Perform the following steps to connect the fiber-optic cable to the SFP port (E1).

1. Remove the dust cap from the SFP port.
2. Insert the transceiver module into the SFP port, and ensure it is in place.
3. Slide the sealing nut, clip, seals, and gland body over the fiber-optic cable.
4. Insert the connector of the fiber-optic cable into the transceiver module, and ensure the connector is firmly in place.
5. Thread the gland body into the SFP port, and tighten to a torque of 45 in/lbs (5.0 Nm).
6. Combine the two split seals over the cable, and place them on the gland body.
7. Move the clip towards the gland body, passing over the seals, until the clip properly fits into the gland body.
8. Tighten the sealing nut onto the gland body to a torque of 36 in/lbs (4.0 Nm).

Figure 10 Fiber-optic Cable and CKIT-OD-SFP SFP Cable Gland

1. Fiber-optic Cable
2. Gland Body
3. Seals
4. Clip
5. Sealing Nut

Software

For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide .

HPE Aruba Networking access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country's regulations. For a complete list of approved channels in your country, refer to the HPE Aruba Networking Downloadable Regulatory Table.

Verifying Post-Installation Connectivity

The integrated LED on the access point can be used to verify that the access point access point is receiving power and initializing successfully (see Table 1-Table 2)

Specifications and Safety

This chapter provides an overview of the HPE Aruba Networking 670 Series Outdoor Access Points specifications, safety, and compliance information.

Specifications

Electrical

• Ethernet
  • E0 port: 100/1000/2500Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port o E1 port: SFP port
• Power
  • Power over Ethernet (PoE): 802.3at or 802.3bt compliant source

Environmental

• Operating
  • Operating Temperature Range: -40°C to +70°C (-40°F to +158°F) (without solar loading)
  • Operating Temperature Range: -40°C to +65°C (-40°F to +149°F) (with solar loading)
  • Operating Humidity Range: 5% to 93% (RH), non-condensing
• Storage
  • Storage Temperature Range: -40°C to +70°C (-40°F to +158°F)
  • Storage Humidity Range: 5% - 93% (RH), non-condensing

For additional specifications on this product, please refer to the HPE Aruba Networking 670 Series Outdoor Access Points data sheet.

Regulatory Model Name

For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number (RMN). The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number RMN is not the marketing name or model number of the product.
The regulatory model name for the HPE Aruba Networking 670 Series Outdoor Access Points:

• AP-674 RMN: APEX0674
• AP-675 RMN: APEX0675
• AP-677 RMN: APEX0677
• AP-679 RMN: APEX0679