Download Print this page

DUSK Sienna Corner TV Unit Manual

Product dimensions: w100xd40xh50 cm

Advertisement

Quick Links

Up to 40 minutes
assembly time
This product is intended for domestic use only, not for commercial purposes.
Corner TV Unit
Two person
assembly
Range Name: Sienna
Box 1 dimensions: L113xW47xH16 cm
Product dimensions: W100xD40xH50 cm
P-1-14
V-2.0

Advertisement

loading
Need help?

Need help?

Do you have a question about the Sienna Corner TV Unit and is the answer not in the manual?

Questions and answers

Summary of Contents for DUSK Sienna Corner TV Unit

  • Page 1 Range Name: Sienna Box 1 dimensions: L113xW47xH16 cm Product dimensions: W100xD40xH50 cm Corner TV Unit Up to 40 minutes Two person assembly time assembly This product is intended for domestic use only, not for commercial purposes. P-1-14 V-2.0...
  • Page 2: Care And Maintenance

    IMPORTANT ASSEMBLY TIP Before you begin, it's best to identify all of the parts and fittings to build your TV unit frame. We advise laying these out on the floor to check you have everything, and to familiarise yourself with all of the parts and fittings before building.
  • Page 3: Parts List

    Parts list P-3-14...
  • Page 4 Parts list Before you begin building your TV unit, please take a moment to read through the instructions and make sure that you have all the relevant parts listed on the parts check list. Part Description Quantity Box No Part Number 1 pc Box 1 Left Side Panel...
  • Page 5 Pre-assembled Fittings Adjustable Foot Pre-assembled x 1pc Bolt Length Ruler: Slides Must Be Separated Before Assembly. Pay attention when connecting ! After Separated, Set Aside Until Needed for Assembly. The sliding module must be at the front end. STEP 1 : Extend Slide Mount Lever STEP 2: Push Lever UP...
  • Page 6 1. Attach Cam Lock Screw to Shelf (8). M6*35mm Cam Lock Screw 2pcs 2. Attach the Slide Rail to Centre Panel (6) two sides, then attach Centre Panel (6) to Shelf (8). Ø6*30mm Dowel M3.5*10mm Screw Ø15*9mm Cam Lock P-6-14 2pcs 2pcs 4pcs...
  • Page 7 3. Attach Cam Lock Screws to Right Side Bar (21) ,then attach Right Side Bar (21) and Right Side Panel (2) . M6*35mm Ø6*30mm Dowel M3.5*10mm Screw Ø15*9mm Cam Lock Cam Lock Screw 2pcs 2pcs 2pcs 2pcs 4. Attach Cam Lock Screws to Left Side Bar (20) ,then attach Left Side Bar (20) and Left Side Panel (1) .
  • Page 8 5. Attach Cam Lock Screw to Left Side Panel (1) and Right Side Panel (2). M6*35mm Cam Lock Screw 6pcs 6. Attach Shelf (8) and Front Support Bar (10) to Right Side Panel (2). Ø6*30mm Dowel Ø15*9mm Cam Lock 3pcs 3pcs P-8-14...
  • Page 9 7. Attach Left Side Panel (1) to the Frame. Ø6*30mm Dowel Ø15*9mm Cam Lock 3pcs 3pcs 8. Attach Left Corner Panel (3) and Right Corner Panel (4) to the Frame. M6*35mm Ø15*9mm Cam Lock Cam Lock Screw P-9-14 4pcs 4pcs...
  • Page 10 9. Insert the Upper Back Panel (9) to the Frame. 10. Attach Cam Lock Screws to Top Panel (11). M6*35mm Cam Lock Screw 8pcs P-10-14...
  • Page 11 11. Attach Top Panel (11) to the Frame. Ø6*30mm Dowel Ø15*9mm Cam Lock 8pcs 8pcs 12. Insert Lower Back Panel (7) into the Frame. P-11-14...
  • Page 12 13. Attach Bottom Panel (5) to the Frame. Ø6*30mm Dowel M4*45mm Screw 6pcs 14pcs 14. Attach Legs (18) and Centre Leg (19) to the Frame. P-12-14...
  • Page 13 15. Assemble the drawer by following the steps shown in the illustration below. M4*35mm Screw M3.5*10mm Screw 8pcs 4pcs 8pcs 16. Assemble the drawer by following the steps shown in the illustration below. M6*35mm Handle Cover M4*20mm Bolt Ø15*9mm Cam Lock Cam Lock Screw P-13-14 8pcs...
  • Page 14 17. Slide the Drawers into the Frame. The Centre Leg is adjustable if necessary. 18. Attach the plastic buckles on back. Before securing them, manually adjust the frame to ensure the drawers are properly aligned, even, and parallel. Plastic Buckle M3.5*14mm Screw 11pcs 11pcs...