Ryobi DP121L Repair Sheet page 4

RYOBI 12 in. DRILL PRESS – MODEL NUMBER DP121L
The model number will be found on a plate attached to the motor housing. Always mention the model
number in all correspondence regarding your DRILL PRESS or when ordering repair parts.
KEY PART
NO. NUMBER
TDP04001
7
08914000080
7
08914000048
74
08914000049 * SCREW (SET W/DOG POINT
75
08914000050
76
08914000067 * SCREW
77
0891400005
78
0891400001
79
10014A
80
0891400005
81
08914000054
8
08914000055
8
08914000056
84
08914000057 * SCREW
85
08914000058
86
08914000059
87
08914000060 * SCREW
88
TDP11001
89
0891400006
90
0891400006
91
08914000064
9
08914000065
9
08914000066
94
08914000088
95
08914000068
96
08914000069
97
08914000087 * SCREW (M4. X 1 mm
98
08914000070
99
08914000074
100
08914000075
101
08914000076
10
08914000084
10
08914000086
104
08914000085
105
08914000071 * ROLL PIN (D.5 X 1 mm) ..1
106
08914000088
107
08914000089
108
PARTS LIST FOR FIGURE A
DESCRIPTION
HEX KEY (4 mm) .................1
HEX KEY ( mm) .................1
PULLEY COVER .................1
M8 X 16 mm HEX SOC.) .....1
RACK ..................................1
(M4 X 8 mm PAN HD.) .........4
SENSOR SEAT ....................1
RUBBER GROMMET ..........
CORD CLAMP W/SLEEVE ..
GEMEL SEAT ......................
MOTOR PULLEY-LOWER ..1
MOTOR PULLEY-UPPER ...1
RETAINING RING (14) .........1
(M4. X 9.5 mm PAN HD.) ...4
GEMEL CLAMP ..................
GEMEL ................................1
(M8 X 5 mm HEX SOC.) ....4
LOCK WASHER (M8) ..........4
WASHER (M8) .....................4
MOTOR PULLEY SPRING ..1
HOOD SPRING ...................1
PALLET SPRING .................1
KEY (M4 X 75 mm) ..............1
MOTOR ...............................1
ROLL PIN (D6 X 16 mm) .....1
HEAD STOCK .....................1
COUNTERSUNK HD.) .........
GEAR SHAFT ......................1
SHAFT SEAT .......................1
RETAINING RING (16) .........1
DEPTH STOP RING ............1
ROD ....................................
KNOB DEPTH SCREW .......1
HUB ....................................1
BULB SOCKET W/NUT ......1
BULB SOCKET-BRACKET ..1
* Standard Hardware Item – May Be Purchased Locally
KEY PART
QTY. NO. NUMBER
0891400008 * SCREW
109
0891400007 * SCREW
110
0891400007
111
08914000074
11
089140000
11
0891400000 * ROLL PIN (D.5 X 16 mm) ..1
114
TDP08001
115
08914000076
116
08914000077
117
1001
118
TDP000
119
08914000901
10
08914000078 * SCREW
11
140600A
1
0891400090
1
08914000905
14
0891400090
15
08914000904
16
08914000905
17
08914000908
18
08914000909
19
08914000907
10
08914000911
11
98440600
1
0891400009
1
0891400010
14
0891400091
15
08914000081 * HEX NUT (M10 mm) ............1
16
0891400008
17
08914000084
18
08914000085
19
08914000086
140
08914000087
141
9800064
06-06-08
(REV:06)
4
DESCRIPTION
(M4 X 1 mm PAN HD.) .......
(M8 X 16 mm HEX SOC.) ....1
WASHER (M8) .....................1
SPRING ...............................1
LASER LIGHT .....................
EXT. TOOTH LOCK WASHER
(M5) .....................................
LED ASSEMBLY ..................1
BAFFLE ...............................1
SPECIAL SET SCREW ........1
* HEX SCREW (M8 X 8 mm) ..1
SCALE LABEL
(FOR BRACKET) .................1
(M5 X 8 mm PAN HD.) .........
TABLE INDICATOR ..............1
DEPTH (STROKE) INDICATOR .1
LASER WARNING LABEL-1 ..1
WARNING LABEL ...............1
DATA LABEL .......................1
SPEED ADJUST LABEL ......1
LOGO LABEL ......................1
LAMP WATT LABEL ...........1
DEPTH SCALE LABEL ........1
LASER WARING LABEL- ..1
SWITCH KEY ......................1
VISE (.5 in.) ........................1
WASHER .............................
LASER LABEL .....................1
CAPACITOR
(MOTOR) DP11L ...............1
CABLE CLAMP ...................1
INSULATING TAPE ..............1
WASHER .............................1
MOTOR CUSHION..............1
OPERATOR'S MANUAL
QTY.