Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita DHP490
Summary of Contents for Makita DHP490
- Page 1 INSTRUCTION MANUAL Cordless Hammer Driver Drill DHP490 Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: DHP490 Drilling capacities Masonry 13 mm Steel 13 mm Wood 38 mm Fastening capacities Wood screw 6 mm x 75 mm Machine screw No load speed High (2) 0 - 1,900 min Low (1) 0 - 500 min... -
Page 3: Safety Warnings
Intended use WARNING: The vibration emission during actual use of the power tool can differ from the The tool is intended for impact drilling in brick, brickwork declared value(s) depending on the ways in which and masonry. It is also suitable for screw driving and the tool is used especially what kind of workpiece drilling without impact in wood, metal, ceramic and is processed. - Page 4 increase the risk of electric shock. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
- Page 5 Battery tool use and care Do not touch the drill bit, the workpiece or chips immediately after operation; they may be Recharge only with the charger specified by extremely hot and could burn your skin. the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire Some material contains chemicals which may when used with another battery pack.
-
Page 6: Tips For Maintaining Maximum Battery Life
Makita warranty for the Makita tool and Do not store and use the tool and battery car- charger. tridge in locations where the temperature may reach or exceed 50 °C (122 °F). -
Page 7: Overload Protection
LXT BASIC 70% - 100% 25% - 70% 0% - 25% Fig.1 Fig.3 ► 1 . Red indicator 2. Button 3. Battery cartridge ► 1 . Indicator lamps 2. Check button CAUTION: Indicator lamps Always install the battery cartridge Error description fully until the red indicator cannot be seen. -
Page 8: Switch Action
This tool is equipped with an electric brake. If the tool lamp, or it may lower the illumination. consistently fails to quickly stop after the switch trigger is released, have the tool serviced at a Makita service Reversing switch action center. -
Page 9: Adjusting The Fastening Torque
To change the speed, switch off the tool first. Push Select the mode suitable for your work. Turn the adjust- the speed change lever to display "2" for high speed ing ring and align the mark that you select with the or "1" for low speed but high torque. Be sure that the arrow on the tool body. speed change lever is set to the correct position before operation. -
Page 10: Installing Hook
The hook is convenient for temporarily hanging the tool. ASSEMBLY This can be installed on either side of the tool. To install the hook, insert it into a groove in the tool housing on either side and then secure it with a screw. To remove, CAUTION: Always be sure that the tool is loosen the screw and then take it out. -
Page 11: Operation
Start the tool slowly and then tool, or abnormal noises are heard. Contact Makita increase the speed gradually. Release the switch trigger service center or your local dealer to have the tool as soon as the clutch cuts in. -
Page 12: Maintenance
Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. OPTIONAL Fig.16 ► 1 . Blow-out bulb... - Page 16 Makita Europe N.V. Jan-Baptist Vinkstraat 2, 3070 Kortenberg, Belgium Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502 Japan 885B11-222 20250108...
Need help?
Do you have a question about the DHP490 and is the answer not in the manual?
Questions and answers