Subscribe to Our Youtube Channel
Related Manuals for Rockwell Automation Allen-Bradley GuardPLC
Summary of Contents for Rockwell Automation Allen-Bradley GuardPLC
-
Page 1: Table Of Contents
Installation Instructions GuardPLC Digital Input Module Catalog Number 1753-IB16 Topic Page Important User Information About the Module General Safety Install the Module Mount the Module Ground the Module Wire the Module Make Connections for Safety-related Communication Reset Push Button Status Indicators Specifications Additional Resources... -
Page 2: Important User Information
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. -
Page 3: About The Module
Do not touch connectors or pins on component boards. • Do not touch circuit components inside the equipment. • Use a static-safe workstation, if available. • Store the equipment in appropriate static-safe packaging when not in use. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... -
Page 4: Environment And Enclosure
Follow these steps to install the module. 1. Mount the module to a DIN rail. 2. Ground the module. 3. Wire the module. 4. Make connections for safety-related communication. This publication describes these steps in detail. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... -
Page 5: Mount The Module
DIN rail materials (for example, aluminum or plastic) that can corrode, oxidize, or are poor conductors, can result in improper or intermittent grounding. Secure DIN rail to mounting surface approximately every 200 mm (7.8 in.) and use end-anchors appropriately. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... -
Page 6: Wire The Module
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 L+ L+ 2 3 4 6 7 8 10 11 12 24V DC Connection of Voltage Supply to Input Device Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... - Page 7 (0). Although the external line is not monitored, a wire break is interpreted as a safe (0) signal. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010...
- Page 8 Digital input 16 Reference pole LS+, not L+, should be used for short-circuit protection. Each LS+ features individual short-circuit and EMC protection that make it important to use LS+ for only its four related inputs. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010...
-
Page 9: Line Control
(that is, when one of the E-stop off switches is pressed in the example above). For information on how to configure inputs and pulse test sources for line IMPORTANT control, see the GuardPLC Controller Systems User Manual, publication 1753-UM001. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... -
Page 10: Make Connections For Safety-Related Communication
The next time you cycle power, these settings will be restored to the last values stored into nonvolatile memory. This means that either the settings prior to the reset will be restored, or if any settings were changed after the reset, those new settings will still be in effect. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... -
Page 11: Status Indicators
Boot Loader unable to load operating system or unable to start COMM operating system loader. Module status can be interrogated through the programming software. For more information, refer to the GuardPLC System User Manual, publication 1753-UM001. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... -
Page 12: Specifications
Switching time Sensor supply 4 x 19.2V / 40 mA @ 24V short-circuit proof Use this Conductor Category information for planning conductor routing. Refer to Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... - Page 13 10V rms with 1 kHz sine-wave 80% AM from • 150 kHz…80 MHz IEC 61000-4-6 • Damped Oscillatory Wave Immunity ±1 kV line-earth (CM) on signal ports • • IEC 61000-4-12 ±1 kV line-earth (CM) on power ports Rockwell Automation Publication 1753-IN004C-EN-P - June 2010...
-
Page 14: Additional Resources
General guidelines for installing a Rockwell Automation industrial system Guidelines, publication 1770-4.1 You can view or download publications at http://www.rockwellautomation.com/literature. To order paper copies of technical documentation, contact your local Rockwell Automation distributor or sales representative. Rockwell Automation Publication 1753-IN004C-EN-P - June 2010... - Page 15 GuardPLC Digital Input Module Rockwell Automation Publication 1753-IN004C-EN-P - June 2010...
-
Page 16: Rockwell Automation Support
Rockwell Automation representative. New Product Satisfaction Return Rockwell Automation tests all of its products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned, follow these procedures.
Need help?
Do you have a question about the Allen-Bradley GuardPLC and is the answer not in the manual?
Questions and answers