Hilti 2142666 Original Operating Instructions
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Nail Gun
  5. 2142666
  6. Original operating instructions
Hilti 2142666 Original Operating Instructions

Hilti 2142666 Original Operating Instructions

Hide thumbs

Advertisement

Table of Contents

DX 5 SM
English
Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 2142666 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hilti 2142666

Summary of Contents for Hilti 2142666

  • Page 1 DX 5 SM English Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...
  • Page 2 Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...

  • Page 3: Information About The Documentation

    Information about the documentation About this documentation • Read this documentation before initial operation or use. This is a prerequisite for safe, trouble-free handling and use of the product. • Observe the safety instructions and warnings in this documentation and on the product. •...
  • Page 4 This symbol indicates when servicing is due. It appears after 5 years, when 30,000 fasteners have been driven, or when the battery is empty. Our recommendation: Please contact Hilti Service. Product information products are designed for professional users and only trained, authorized personnel are permitted to operate, service and maintain the products.
  • Page 5 ▶ Use only Hilti cartridges or cartridges of equivalent quality. ◁ Use of cartridges of inferior quality in Hilti tools may lead to a build-up of unburned powder, which may suddenly explode and cause severe injuries to operators and bystanders. The cartridges must be either verifiably tested by the manufacturer in accordance with EU standard EN 16264 or they must bear the CE conformity marking.
  • Page 6 ▶ Do not use the tool in places where there is a risk of fire or explosion unless the tool is specially approved for this type of use. ▶ Never drive fasteners into existing holes unless this is recommended by Hilti (e.g. DX-Kwik). Workstation ▶...
  • Page 7 English Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...
  • Page 8 English Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...
  • Page 9 Description Overview of the product English Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...

  • Page 10: Technical Data

    Cartridges All Hilti cartridges for powder-actuated tools have been tested successfully in accordance with EN 16264. These tests are carried out by the certification bodies using specific combinations of cartridges and tools.

  • Page 11: Operation

    DX 5 SM 5 ℉ …122 ℉ Application temperature (ambient temperature) (−15 ℃ …50 ℃) 1.3 in Compression stroke (32 mm) Operation Safety devices Before commencing work, check that all safety devices are fitted and that they are functioning correctly. All parts must be fitted correctly and fulfill all conditions necessary for the correct operation of the tool.
  • Page 12 1. Press the power regulator release button. 2. Turn the power regulating wheel to set the power level you require. 3. Check the quality of the fastening in accordance with Hilti standards. Select a cartridge power level and power setting to suit the application.
  • Page 13 Unloading the magazine tool 1. Pull the cartridges out of the tool. 2. To remove unused fasteners from the magazine, turn the loading / unloading button to a right angle relative to the magazine. ◁ The collated fasteners can be removed. 3.

  • Page 14: Care And Maintenance

    This can only be reduced by having the tool taken to Hilti Service for maintenance. ▶ Clean the exterior of the tool with a slightly damp cloth at regular intervals.
  • Page 15 ◁ If the required contact pressure increases noticeably. ◁ If the trigger resistance increases. ◁ If the power regulation wheel is stiff. ◁ If the cartridge strip is difficult to remove. ◁ If the maintenance indicator shows that a tool service is necessary. Dismantling the magazine tool 1.
  • Page 16 1. Check the fastener guide for wear and replace it if part of it is damaged (e.g. broken, bent, widened or cracked). 2. Contact Hilti Service if necessary. Cleaning and lubricating the magazine tool 1. Spray the piston rings lightly with oil and then use the flat brush to clean them using the flat brush until the rings are free to move.

  • Page 17: Troubleshooting

    5. Clean the exhaust gas piston return unit. 6. Spray the cleaned parts with the supplied Hilti lubricant spray. Use only Hilti lubricant spray or a product of comparable quality. Use of other lubricants may damage the tool. 7. Spray the power regulation wheel with the Hilti spray supplied with the tool.
  • Page 18 Trouble or fault Possible cause Action to be taken Build-up of combustion residues. ▶ Service the tool. The exhaust gas piston return unit jams. The tool was not pressed fully ▶ Press the tool fully against the against the working surface. working surface.
  • Page 19 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.

  • Page 20: Manufacturer's Warranty

    Confirmation of C.I.P. testing The following applies to C.I.P. member states outside the EU and EFTA judicial area: The Hilti DX 5 has been system and type tested. As a result, the tool bears the rectangular PTB approval mark showing approval number S 995.
  • Page 21 Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...
  • Page 22 Hilti = registered trademark of Hilti Corp., Schaan 20180726 Printed: 02.08.2018 | Doc-Nr: PUB / 5292662 / 000 / 02...

This manual is also suitable for:

Dx 5 sm

Table of Contents