Advertisement
Quick Links
Advertisement
Related Manuals for Hilti DX 76-MX
Summary of Contents for Hilti DX 76-MX
- Page 1 DX 76-MX DX 76-PTR Quick Start Guide – Supplement...
- Page 2 KNOWING HOW TO CLEAN 9 – 10 THE TOOL POSSIBLE CAUSES CARTRIDGES KNOWING ESSENTIAL FIELD TROUBLE SHOOTING POSSIBLE CAUSES NAILS Additional resources available are: ̵ Tool Operating Instructions ̵ How to video (use the resources in Hilti online or Hilti channel in YouTube)
-
Page 3: Personal Protective Equipment (Ppe)
The tool is intended for professional use. The tool may be operated, serviced and maintained only by trained, authorized personnel who have received special instruction regarding the hazards that may be encountered. Use the tool for the first time only after you have been trained by a Hilti specialist on how to use it safely. Personal Protective Equipment (PPE) Operator and bystanders must wear helmet, eye and ear protection. - Page 4 TOOL ANATOMY DX 76-MX INDEX Contact Fastener Cycling Power Stop Grip Regulation Wheel Spall Cartridge Strip Power Padded Guard Guideway Regulation End Cap Indicator Sliding Piston Guide Trigger Grip Pad Sleeve Release Lever Piston Nail Magazine Piston Stopper Piston Fastener...
- Page 5 TOOL ANATOMY DX 76-PTR INDEX Contact Fastener Cycling Power Stop Grip Regulation Wheel Spall Cartridge Strip Power Padded Guard Guideway Regulation End Cap Indicator Sliding Piston Guide Trigger Grip Pad Sleeve Release Lever Piston Nail Magazine Piston Brake Piston Fastener X-76-P-ENP-PTR assembly X-ENP-19 X-76-P-ENP2K-PTR assembly...
- Page 6 (6 mm). Select the right tool & Select the right tool & piston piston DX 76-PTR tool can be DX 76-MX tool is used used when punching though for most applications and the deck is a concern, use markets. X-76-P-ENP2K-PTR piston.
- Page 7 Piston fastening the deck. Brake/Stop and subsequent damage to the Nail Detec- tion Mechanism Tip: For DX 76-MX/PTR load 1 nail strip first and then always load nails when cartridge strip runs out. Load the cartridge...
- Page 8 FASTENING METAL DECK TO THE STEEL STRUCTURE INSTALLING THE DECKING NAIL INDEX Check nail stand-off and adjust power level if required Initially, then periodically while fastening, and any time you change base mate- rial, use the Power Adjust- ment Gauge to check the nail stand-off and adjust the tool power level.
- Page 9 INDEX Disassamble the tool Remove the cartridge strip and nails before disassembling the tool. While cleaning the tool, the Hilti spray should be applied Clean the tool ONLY on the Nail Magazine and NOT inside the tool. Check the Piston and Change if either the Piston or Piston Stopper is worn.
- Page 10 KNOWING HOW TO CLEAN THE TOOL INDEX Check the Piston and Change if either the Piston or Piston Brake is worn. Piston Brake Change only as a set both Piston and Piston Brake. Assemble the tool Check the Piston Brake/Stop and Piston is always assembled back in.
-
Page 11: Recommended Action
Cartridges are not transported The tool is damaged Send DX 76 Tool to Hilti Tool Service Center Allow tool to cool, then carefully try to remove the The tool is damaged or has over- cartridge strip. Remove the piston guide from the Cartridge Strip can’t... - Page 12 KNOWING ESSENTIAL FIELD TROUBLE SHOOTING POSSIBLE CAUSES NAILS INDEX X-ENP-19 Issue Visual Criteria Trouble Possible cause Action No piston mark visible, Deck is not fas- Power setting too Dial up power Nail stand-off nail head stays off, tened properly to low or cartridge setting or increase too high...