Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LTS LTWB-5AC-360
Summary of Contents for LTS LTWB-5AC-360
- Page 1 Wireless Bridge (Web) User Manual...
-
Page 2: Legal Information
Wireless Bridge (Web) • User Manual Legal Information About this Manual The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. -
Page 3: Symbol Conventions
Wireless Bridge (Web) • User Manual Preface Symbol Conventions The symbols that may be found in this document are defined as follows. Symbol Description Indicates a hazardous situation which, if not avoided, will or could Danger result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in equipment damage, data loss, performance degradation, or Caution... -
Page 4: Table Of Contents
Wireless Bridge (Web) • User Manual Contents Introduction ........................1 Activation and Login ...................... 2 Activate the Device ......................2 Log in to the Device ......................2 Overview ........................3 Network Settings ......................5 WAN Settings ........................5 LAN Settings ........................6 Data Forwarding Settings .................... - Page 5 Wireless Bridge (Web) • User Manual Why the signal intensity is too low? ................23 Why the throughput is inadequate even with high signal quality? ......... 23 Why there are excessive packet loss and time delay when PC pings the device IP address? ..............................
-
Page 6: Introduction
Wireless Bridge (Web) • User Manual Introduction You can manage and configure the wireless bridge (hereinafter referred to as the device) through the web browser, including network settings, wireless network settings, and system management. Note Functions vary with device models. Pictures used for illustration here are for example purposes. The actual interface prevails. -
Page 7: Activation And Login
Wireless Bridge (Web) • User Manual Activation and Login Activate the Device For the security of your privacy and system data, you are required to set a password for your first use. After the password is set, you can log in to the web for further configuration. Before You Start Ensure that your PC and the device are on the same network segment. -
Page 8: Overview
Wireless Bridge (Web) • User Manual Overview You can view the basic information, connection status, network status, and wireless status for routine check or device maintenance. Overview Overview Description Information&Operation Description Device Information Check device name, device model, serial No., program version, MAC address, CPU usage, memory usage, running time, and background noise condition of the device, etc. - Page 9 Wireless Bridge (Web) • User Manual 7days. See Chapter 7 PoE Management for details. Check clound platform connection status. This function varies with Cloud Platform models. The actual interface prevails. Quick Set Time Click Set Now to set system time. See 9.7 Set Time for details. Quick Modify Device Click to modify device name.
-
Page 10: Network Settings
Wireless Bridge (Web) • User Manual Network Settings WAN Settings Go to Network Settings → LAN Settings to set relevant parameters, such as Network Access Method and WAN IPv4. Note The function varies with models, and it is only supported when some devices are set as AP site. The actual interface prevails. -
Page 11: Lan Settings
Wireless Bridge (Web) • User Manual LAN Settings Go to Network Settings → LAN Settings to configure detailed network parameters. If you enable Auto-obtain Dynamic IP, other parameters will be set automatically. LAN Settings Note The function varies with models. Devices with WAN port is supported to configure DHCP server. - Page 12 Wireless Bridge (Web) • User Manual Enable Self-Adaptive Packet Filtering Disable Self-Adaptive Packet Filtering Parameter Description Parameter Description Self-Adaptive Enabled by default. Filter packets according to present rules, in order to Packet Filtering reduce the impact of excessive message on the device in the LAN. Filter SADP multicast packets to minimize the negative influence brought by massive SADP multicast packets in the LAN.
-
Page 13: Wireless Settings
Wireless Bridge (Web) • User Manual Wireless Settings Click Wireless Settings to set basic and advanced parameters of wireless network. Basic Wireless Settings Go to Wireless Settings → Basic Settings to set wireless network basic parameters. Wireless Network Basic Settings Note The picture used above is an example of a device with DIP switch function. - Page 14 Wireless Bridge (Web) • User Manual Parameter Description Parameter Description Enable/disable the pairing code and scene switching function through the DIP switch. This function is enabled by default. Note Enable DIP Switch ● If the DIP group numbers are not enough for use, you can disable this function and set SSID accordingly.
-
Page 15: Advanced Wireless Settings
Wireless Bridge (Web) • User Manual Parameter Description The power transmitted in the direction of peak radiation to that of an Antenna Gain isotropic source. Click Scan and select an optimum channel to check the signal intensity of Signal Scanning available channels nearby. -
Page 16: Admin Ssid
Wireless Bridge (Web) • User Manual Admin SSID Support mobile phones and PCs to manage AP/CPE device by connecting to the device wireless network, for configuration such as setup and maintenance. Note The function is only available for some models. The actual interface prevails. ... -
Page 17: Vlan Management
Wireless Bridge (Web) • User Manual VLAN Management VLAN (Virtual Local Area Network) is a technology that logically (rather than physically) divides devices within a local area network into individual network segments, thereby achieving the isolation of broadcast domains within a local area network. Note The function is only available for some models. -
Page 18: Poe Management
Wireless Bridge (Web) • User Manual PoE Management Click PoE Management to manage PoE port as desired. Note The function is only available for some models. The actual interface prevails. PoE Management Enabling PoE watchdog can automatically detect the connection status of devices connected to the PoE port. -
Page 19: Terminal Security
Wireless Bridge (Web) • User Manual Terminal Security Go to Terminal Security and select the appropriate mode. The device can identify the brand of terminals and match security policies to achieve terminal classification management. Note The function is only available for some models. The actual interface prevails. Terminal Security ... -
Page 20: System Configuration
Wireless Bridge (Web) • User Manual System Configuration System Diagnosis Export desired logs to your local storage. Steps 1. Go to Diagnosis → Log Management. 2. Click Export to save the log files. Through Ping Tool, you can get network status information, which would be useful for the technical support. -
Page 21: Wireless Bandwidth Test
Wireless Bridge (Web) • User Manual Technicians can determine whether the wireless network is smooth through wireless bandwidth testing. Note The function is only available for some models. The actual interface prevails. Steps 1. Go to Diagnosis → Network Tool → Wireless Bandwidth Test. 2. -
Page 22: Http(S)
Wireless Bridge (Web) • User Manual 2. Enable SSH. Note The user name of SSH Client is root, and the password is the same as that of web login. The HTTP protocol (Hypertext Transfer Protocol) is an application layer transport protocol based on the TCP protocol, while the HTTPS protocol (Secure Hypertext Transfer Protocol) is a network protocol built on SSL+HTTP protocol that can perform encrypted transmission and identity authentication. -
Page 23: Sadp Service
Wireless Bridge (Web) • User Manual If SADP service is enabled, you can activate the device, change password, and modify IP address through the software. SADP service is enabled by default. Steps 1. Go to System → Security Management → SADP. 2. -
Page 24: Upgrade The Device
Wireless Bridge (Web) • User Manual Upgrade the Device Use the newest firmware for available upgrades, and upgrade the device through web page remotely. Before You Start Copy the upgrade package to the local directory of the PC used for remote access. Steps 1. -
Page 25: Manual Setting
Wireless Bridge (Web) • User Manual 4. Set the desired time or check Sync. With Computer Time. Manual Setting 5. Click Save. NTP time synchronization is used to synchronize the time with that of a specific NTP server. Steps 1. Go to System → System Configuration → Time Configuration. 2. -
Page 26: Change Password
Wireless Bridge (Web) • User Manual The IP address of the NTP server. NTP Port Monitoring port of the NTP server. Default value: 123. Value range: 1 to 65535. Sync. Interval The frequency for the device to synchronize with the NTP server. Value range: 1 to 10080 minutes. -
Page 27: Faqs
Wireless Bridge (Web) • User Manual FAQs Why the device cannot start up? Reason 1. The network cable length connecting the wireless bridge to the PoE module exceeds 60 m. 2. The network cable cannot meet the standard of Category 5e. 3. - Page 28 Wireless Bridge (Web) • User Manual Why the signal intensity is too low? Reason 1. There is a large-sized obstruction between the CPE and the AP. 2. The CPE is not directly faced to the AP. Solution 1. Remove the obstruction or bypass it. Adjust the angle of the CPE and the AP.
Need help?
Do you have a question about the LTWB-5AC-360 and is the answer not in the manual?
Questions and answers