Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for LTS LTN07 R8 Series
Summary of Contents for LTS LTN07 R8 Series
- Page 1 Network Video Recorder Quick Start Guide...
-
Page 2: Table Of Contents
Quick Start Guide of Network Video Recorder TABLE OF CONTENTS NVR Pre-Installation ........................... 3 NVR Installation ............................3 Hard Disk Installation ..........................3 Front Panel ..............................6 Rear Panel7 Peripheral Connections ..........................8 Wiring of Alarm Input ..........................8 Wiring of Alarm Output ..........................8 Using of Alarm Connectors ......................... - Page 3 Quick Start Guide of Network Video Recorder Regulatory information FCC information This equipment has been tested and found to comply with the limits for a digital device, pursuant compliance: to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
-
Page 4: Nvr Pre-Installation
Quick Start Guide of Network Video Recorder VGA is the trademark of IBM. UPnP is a certification mark of the UPnP Implementers Corporation. Other names of companies and product contained in this manual may be trademarks or registered trademarks of their respective owners. - Page 5 Quick Start Guide of Network Video Recorder 2. Insert the key and turn in clockwise direction to open the panel lock. 3. Press the buttons on the panel of two sides and open the front panel. 4. Insert the hard disk along the slot until it is placed into position. 5.
- Page 6 Quick Start Guide of Network Video Recorder...
-
Page 7: Front Panel
Quick Start Guide of Network Video Recorder Front Panel POWER ALARM Tx/Rx HDD READY ARCHIVE Name Description Turning red indicates power is connected but the system isn’t Power running; turning blue indicates power is connected and the system is running. Alarm Alarm LED turns red when a sensor alarm is detected. -
Page 8: Rear Panel7
Quick Start Guide of Network Video Recorder Rear Panel Item Description USB interface Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). AUDIO IN RCA connector for audio input. AUDIO OUT RCA connector for audio output. -
Page 9: Peripheral Connections
Quick Start Guide of Network Video Recorder Peripheral Connections Wiring of Alarm Input The alarm input is an open/closed relay. To connect the alarm input to the device, use the following diagram. If the alarm input is not an open/close relay, please connect an external relay between the alarm input and the device. -
Page 10: Controller Connection
Quick Start Guide of Network Video Recorder 3. Connect pluggable block back into terminal block. Controller Connection To connect a controller to the NVR: 1. Disconnect pluggable block from the KB terminal block. 2. Unfasten stop screws from the KB D+, D- pluggable block, insert signal cables into slots and fasten stop screws. -
Page 11: Specifications
Quick Start Guide of Network Video Recorder Specifications Model LTN0732-R8 LTN0764-R8 IP video input 32-ch 64-ch Video/Audio input 1-ch, RCA (2.0 Vp-p, 1kΩ) Two-way audio Incoming bandwidth 384Mbps 768Mbps 768Mbps Outgoing bandwidth Remote connection PRIVATE, ACTi, ARECONT, AXIS, BOSCH, BRICKCOM, CANON, HUNT, ONVIF(Version 2.4), PANASONIC, PELCO, PSIA, SAMSUNG, SANYO, SONY, Network Protocol VIVOTEK, ZAVIO... -
Page 12: Hdd Storage Calculation Chart
Quick Start Guide of Network Video Recorder HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. Bit Rate Storage Used 128K 160K 192K 224K... -
Page 13: Accessing By Web Browser
Quick Start Guide of Network Video Recorder Accessing by Web Browser Logging In You can get access to the device via web browser. Open web browser, input the IP address of the device and then press Enter. The login interface appears. Input the user name and password, and click the Login button. -
Page 14: Recording
Quick Start Guide of Network Video Recorder Interface Introduction Name Description Displays the list of channels and the playing and recording status of each channel. Channel List The stream type can be switched by clicking the icon before the channel name: stands for main stream and for sub-stream. - Page 15 Quick Start Guide of Network Video Recorder 3. Check the checkbox of Enable Schedule to enable recording schedule. 4. Choose the day in a week to configure scheduled recording. 5. Click Edit to edit record schedule. 1) Configure All Day or Customize Record: ...
-
Page 16: Playback
Quick Start Guide of Network Video Recorder 7. Click Save to validate the above settings. 8. (Optional) You can click the Copy to… button to copy the same setting to other cameras. Playback Interface Introduction Name Description Channel List Displays the list of channels and the playing status of each channel. Playback Window Displays the image of channel. -
Page 17: Log
Quick Start Guide of Network Video Recorder Playback Control Buttons Description Area Description Area Description Play/Pause Stop Slow down Speed up Play by single frame Capture Stop all playback Download Video clip Open/Close audio Reverse playback Window division You can drag the progress bar with the mouse to locate the exact playback point. You can also input the time in the textbox and click button to locate the playback point. -
Page 18: Menu Operation
Quick Start Guide of Network Video Recorder Menu Operation Menu Structure The menu structure LTN07XX-R8 series NVR is shown below: Startup and Shutdown Proper startup and shutdown procedures are crucial to expanding the life of the NVR. To start your NVR: 1. -
Page 19: Adding Ip Cameras
Quick Start Guide of Network Video Recorder In the live view mode, there are icons at the upper-right corner of the screen for each channel, showing the status of the record and alarm in the channel, so that you can find problems as soon as possible. Alarm (video loss, tampering, motion detection or sensor alarm) Record (manual record, continuous record, motion detection or alarm triggered record) Alarm &... -
Page 20: One-Touch Raid Configuration
Quick Start Guide of Network Video Recorder Click the Custom Adding button to pop up the Add IP Camera (Custom) interface. You can edit the IP address, protocol, management port, and other information of the IP camera to be added. Click Add to add the camera. -
Page 21: Recording
Quick Start Guide of Network Video Recorder 3. Click One-touch Configuration to enter the One-touch Array Configuration interface. 4. Edit the array name in the Array Name text filed and click OK button to start configuring array. If you install 4 HDDs or above for one-touch configuration, a hot spare disk will be set by default. It is recommended to set hot spare disk for automatically rebuilding the array when the array is abnormal. -
Page 22: All-Day Recording
Quick Start Guide of Network Video Recorder Click the icon to enable the record, and the icon turns to . And click icon to disable the record, then the icon turns to All-day Recording Steps: 1. On the live view window, right lick the window and move the cursor to the Start Recording option, and select Continuous Record or Motion Detection Record on your demand. -
Page 23: Backup
Quick Start Guide of Network Video Recorder 2. Playback management. The toolbar in the bottom part of Playback interface can be used to control playing process. Just check the channel or channels if you want to switch playback to another channel or execute simultaneous playback of multiple channels. - Page 24 Quick Start Guide of Network Video Recorder 3. Check backup result. Choose the record file in Export interface and click button to check it.
Need help?
Do you have a question about the LTN07 R8 Series and is the answer not in the manual?
Questions and answers