Rtty (Radio Teletype) Operation; Setting Up For Rtty Operation; Basic Setup - Yaesu FT-2000 Operating Manual

RTTY ( R
Most RTTY operation today is accomplished using a TNC or other computer-based system that utilizes AFSK tones. As
such, the previous discussion on LSB-mode "Packet" operation will apply for Baudot operation, as well. For RTTY opera-
tion using a Terminal Unit (TU) or the "FSK" output from a TNC, please see the discussion below. See also the illustration
for details regarding connection to your TU.
RTTY
Before commencing RTTY operation, please direct your
attention to the setup steps shown in the chart to the right.
1. Press the [ RTTY ] button to enter the RTTY mode.
One press of the [ RTTY ] button will engage RTTY
operation using "LSB" injection, which is generally
used in the Amateur service. In this mode, both the
"RTTY" and "LSB" LEDs will light up.
To switch to USB-side injection in RTTY, press the
[ RTTY ] button once more. Both the "RTTY" and
"USB" LEDs will now be illuminated. Repeatedly
pressing the [ RTTY ] button will toggle between LSB
and USB injection on RTTY.
2. When you begin typing on your TU or computer key-
board, the command to transmit should automatically
be sent to the transceiver, causing it to enter the trans-
mit mode.
N :
If you anticipate making data transmissions of longer than
a few minutes, we recommend that you use the [ RF PWR ]
knob to reduce the transmitter power to 1/2 ~ 1/3 of its
normal maximum.
A :
There is no adjustment of the DATA input level (Pin 1
("DATA IN") of the RTTY jack) on the rear panel;
please make any needed level adjustments at the TU
side.
FT-2000D O
ADIO
② ③
① ④ RTTY JACK
Pin 1 ( SHIFT )
Pin 2 ( RX OUT )
( PTT )
Pin 3
Pin 4 ( GND )
S U
ETTING P FOR
B
ASIC
M
T
ELETYPE
RTTY Machine
FSK OUT
AF IN
PTT
GND
RTTY O
PERATION
M I
076 rtty R PLRTY
077 rtty T PLRTY
078 rtty RTY OUT
079 rtty OUT LEL
080 rtty SHIFT
081 rtty TONE
S
ETUP
The Mark/Space Shift utilized in most Amateur RTTY
operation is 170 Hz. Other shifts may be configured,
however, using Menu item "080 rtty SHIFT."
The FT-2000D is set up for "high tone" operation (cen-
tered on 2125 Hz) by default, but you may configure it
for low tone (1275 Hz) operation using Menu item
"081 rtty TONE."
You may find that you are unable to decode some RTTY
stations, even if they are of sufficient signal strength.
If this is observed, there may be a Mark/Space polarity
problem between your station and the other station. If
so, try setting Menu item "076 rtty R PLRTY" to "rEU"
("Reverse") to see if that permits copy. A separate Menu
item permits reversal of your transmitter's Mark/Space
polarity: "077 rtty T PLRTY."
Q P :
In the FT-2000D, "RTTY" is a mode defined as being an
"FSK" mode, whereby the closing and opening of a key-
ing line (to ground) causes the Mark/Space tones to alter-
nate. The RTTY mode is not an AFSK based mode in this
transceiver, and the AFSK output tones from a TNC will
not cause Mark/Space shifting to occur. Use the "Packet"
mode for AFSK-based Baudot and other data modes.
) O
PERATION
FSK FSK
PTT OUT
A V
nor (normal) / rEU (reverse)
nor (normal) / rEU (reverse)
nAin (Main) / Sub (Sub)
0 ~ 100
170/200/425/850 Hz
1275/2125 Hz
Page 109
IN