Subscribe to Our Youtube Channel
Related Manuals for U.S. Solid JF-8000
Summary of Contents for U.S. Solid JF-8000
- Page 1 CAROUSEL TAPE DISPENSER JF-8000 INSTRUCTION MANUAL For questions or concerns, e-mail service@ussolid.com, visit www.ussolid.com, or call 1-800-243-5428...
- Page 2 SPECIFICATION FIGURE REMARK PARTS NAME 4.5X8.7L Coil Spring � M3X14.0L Cross Round Head Screw 2 � Cam Shaft Tape Divide Cam Inward Arm/Tape Bite Cam Inward Lever Cam 42:T Blade cam Reverse Lever Cam Cam Shaft Bushing Small ACETAL Housing Coil Spring 8.5X21.4L Plan Washer 5X10X0.5t...
-
Page 3: Precaution
Precaution Rotator Switch Coil Spring Thank you for buying Auto Tape Dispenser model JF-8000. Please read this Instruction Manual carefully. For your safety, keep this Instruction Manual for reference and troubleshooting. II. Warning 1) Make sure the POWER SWITCH is "OFF" when you set the tape. -
Page 4: Table Of Contents
PARTS NAME SPECIFICATION FIGURE REMARK 2X13.0L Tape Bite Rod Pin Tape Bite Pin 3.0X38.0L Inward Arm Coil Spring 7 0X23 0L Contents , ______ ------ Lower Blade Loading Unit Blade Changing Lever 1. Precaution------------------------------------------------4-6 2. Description of Parts and Functions------------------7 Blade Guide SPC 1.01 3. -
Page 5: Specification
FIGURE PARTS NAME SPECIFICATION REMARK Middle Gear(High Speed) 232-1 Power Switch Inlet Do not expose the machine in Dropping the machine can the sun for a long time. lead to failure of the machine or injury to the operator. Tapping Screw 2 M3X5L 23:l �... - Page 6 7. Do not use this machine for anything other that its PARTS NAME SPECIFICATION FIGURE REMARK specified applications. Frame Cover Use of the machine for any unintended applications can cause injury to the operator or failure of the machine. Frame Cover Latch �...
-
Page 7: How To Operate The Tape Dispenser
How to Operate the Tape Dispenser SPECIFICATION PARTS NAME FIGURE REMARK Reverse Lever ----- Reverse Lever Steel Plate 1.0t Truss Head Tapping Screw M4X8.0L 1. Turn the POWER SWITCH off. � Micro Switch Lever 2. Open the(129)safety cover. Washer Head Tapping M3X8.0L Screw 2 Caution - For your safety, make sure that SAFETY COVER is... -
Page 8: Description Of Parts And Functions
Description of Parts and Functions Linward Gear PARTS NAME SPECIFICATION FIGURE REMARK Disk Switch Disk Safety Cover 1111 M4X10L Truss Head Screw lliJ Upper Blade Gear Cover Manual Lever Tape Guide Plate Manual Lever Latch Washer Head Tapping M3X6L Screw 2 Motor Connect Gear Middle Gear IBDII Tape Distance Control Knob... -
Page 9: Loading The Tape
Loading the Tape PARTS NMAE SPECIFICATION FIGURE REMARK Tape Divide Adjust Cam (� Tape Divide Adjust Cam Stopper Tape Length Adjust Cam � Tape Length Adjust Cam Stopper 1. Make sure the POWER SWITCH is off. � Cam Stopper Cover 2. - Page 10 7. Press the (316)Disk Switch once, the machine will start cutting immediately. The cut pieces will be distributed to half the disk. Then the machine will stop cutting, and you need to push the (316)Disk Switch again to re-operate the machine. You can adjust the tape length with (120)Tape Length Control Knob, and adjust the cut-piece spacing with (120-1)Tape Distance Control Knob.
-
Page 11: Replacing The Upper And Lower Blades
Replacing the Upper and Lower Blades The blades are consumable, and they will eventually worn out. If it happens, please replace a new one. The staying power of blades are based on the tape's quality, material, thickness which you are using. he blades are very sharp. - Page 12 P arts list & Oder No PARTS NAME Cover LH SPECIFICATION FIGURE REMARK c�� Upper Break Roller � 1a:! �.d) Upper Roller Shaft Pin 4.0X42.2L Coil Spring 4.5X7.0L 5. Passing the tape between the UPPER and LOWER BLADE, � ( Jf' J m and affix the tape on the disk.
-
Page 13: Maintenance & Specifications
Maintenance & Specifications Warning: The BLADES are very sharp. Do not touch the BLADES by hand. When performing any maintenance, make sure the POWER SWITCH is "OFF". ■If you have been using the tape dispenser for a long time, tape residue starts to stick on the blades, and it becomes harder to cut. - Page 14 2. Lift the axis of (419)Lower Blade Torsion Spring. Then you can remove the lower blade from the machine. 3. After replacing the blade unit, move (244)Manual Lever Handle from one side to the other side. It will lock the blades with"click”sound.
-
Page 15: Exploded Views/ Parts Breakdown
Exploded Views/ Parts Breakdown '· ..·,.., ..·, - 17 - - 1 6 -... -
Page 16: Specifications
Specifications '· ....·,., '·, ..� ....'·,.i_ '•,., • ..·-· ,· Recommended Tapes This carousel tape dispenser can be used with most adhesive tapes, including high temperature tape, goldfinger tape, scotch tape, acetate cloth, glass cloth, aluminum foil, cellophane tape, masking tape, polyethylene, vinyl tape, teflon tape, mylar tape and etc.
Need help?
Do you have a question about the JF-8000 and is the answer not in the manual?
Questions and answers