Vimar SMART HOME VIEW WIRELESS 30810 Series Manual

SMART HOME VIEW WIRELESS
30810.x - 02973 Connected dial thermostat
THREE OPERATING MODES (ALTERNATIVE)
Stand alone •
Download the View Wireless App from the stores onto the tablet/smartphone you
will be using for configuration.
When the device is powered for the first configuration, we recommend you search for any
new firmware and perform the update.
Depending on the mode you select, you will need:
Stand alone
Gateway
art. 30807.x-20597-19597-16497-14597
View App
Nothing else
for management via smartphone/tablet
Amazon Alexa, Google Assistant, Siri (Homekit)
voice assistants for possible voice operation
Create your Installer account on MyVimar (on-line).
STAND ALONE CONFIGURATION
1. Wire all the thermostats.
2. Start the View Wireless App and log in with the credentials you just created.
3. Create the system and the environments.
4. Associate all the thermostats with the environments.
To associate the thermostat:
• Select "Add" ( ), choose the environment to place it and give it a name
• Select ; activate the Bluetooth connection on your tablet/smartphone and approach the
thermostat
• Press for 5 s; the ring flashes blue and association is complete.
5. For each thermostat, set the functions and parameters.
6. Go to the "Temperature control" menu and for each thermostat set the time schedules, the
setpoints for the operating modes and the current time.
Note: In the event of a mains power outage and subsequent restoration, the product will return to
operating in manual mode with the last set point set. You will therefore need to set the date/time
(see paragraph entitled "Thermostat date/time setting") to restore operation in automatic mode.
CONFIGURATION IN
1. Wire all the devices in the system (2-way switches, relays, thermostats, gateway, etc.).
2. Start the View Wireless App and log in with the credentials you just created.
3. Create the system and the environments.
4. Associate all the devices with the environments, except for the gateway (which should be
associated last).
To associate the thermostat:
• Select "Add" ( ), choose the environment to place it and give it a name
• Select ; activate the Bluetooth connection on your tablet/smartphone and approach
the thermostat
• Press for 5 s; the ring flashes blue and association is complete.
5. For every device, set the function, the parameters and any accessory devices (wired or radio
control and related function).
6. Transfer the configuration of the devices to the gateway and connect it to the Wi-Fi network.
7. Transfer the system to the Administrator user (who must have created his/her profile on
MyVimar).
For full details, see the View Wireless App manual that can be downloaded from the www.
vimar.com website.
CONFIGURATION IN
Follow the procedure above from points 1 to 2.
Associate the device directly to a ZigBee Hub (e.g. Amazon Echo Plus, SmartThings Hub)
1) Download the Zigbee software using the View Wireless App (see the View Wireless App
manual). Press the key on the device until the display shows "bt" and the ring blinks in
blue. To update the software on the device, the procedure is the same.
2) After conversion to Zigbee technology (or the software update), the device automatically goes
into pairing mode for 5 minutes, during this period the Lightable ring blinks white. If the device
is not in pairing mode, cut off the power supply and restore it after a few seconds.
3) Associate the device according to the procedure envisaged by the ZigBee Hub.
4) Associate the module according to the procedure envisaged by the ZigBee Hub (see the Hub's
manufacturer documentation).
Set the thermostat parameters.
Within the first 10 minutes after the device has been powered (already associated with ZigBee
Hub) or after restart at the conclusion of Zigbee association, press the key related to the
parameter to be changed as stated below.
30810.x-02973 06 2411
•
Smart Home Hub
Samsung SmartThings
Hub
A
B
1
• Short press = degrees Celsius/Fahrenheit selection
• Long press (5 s) = the thermostat enters the configuration phase (bt)
• Prolonged press (30 s) within the first 5 min of powering = device reset (rst)
Display brightness and RGB LED in standby setting
• 1st press = current brightness display
• Subsequent presses = cyclic display of available brightness values L-3 (high), L-2
(medium), L-1 (low) and L-0 (off).
• bt = devices in Bluetooth configuration
• off = thermostat off; on = thermostat on
• °C = degrees Celsius; °F = degrees Fahrenheit
A
• L-0, L-1, L-2, L-3 = brightness in standby (from the lowest to the highest)
• H = heating; C = air conditioning
• opn = open window (associated with the thermostat via magnetic contact art.
03980)
B
Dial
C Lightable ring
• Power on and off.
Upon power on or off, the thermostat starts in the last operating mode associated
with it set via the View* App or View Wireless* App.
• Heating or air conditioning mode selection.
* Only for Bluetooth technology
Ring signalling
All flashing blue = thermostat in configuration mode
All lit amber* = thermostat in heating mode and relay active
All lit blue** = thermostat in air conditioning mode and relay active
• Lit amber * = thermostat in heating mode and relay not active
• Lit blue ** = thermostat air conditioning mode and relay not active
1
In standby, the brightness is set during configuration; otherwise, the value is the
maximum one.
• Flashing red = the thermostat, in automatic mode, has lost the hourly value and
has therefore switched to manual mode.
2
When it receives the hourly value from the gateway again, the thermostat returns
to automatic mode and the flashing ends.
* Amber with automatic colour or of the selected colour.
** Blue with automatic colour or of the selected colour.
1. Set the winter/summer calibration
- Press key for 5 s this starts the configuration for choosing the "heating offset temperature"
within 2 minutes timeout. The Lightable ring will flash amber and "H" apperas on the display
to indicate the "heating offset temperature" adjustment; by turning the Dial it is possible to set
a temperature offset. The Lightable ring flashes amber and the offset appears on the display.
- Press key for 5 s to confirm the "heating offset temperature". The "C" now appears on
the display and the crown flashes cyan at maximum brightness and 2 minutes timer starts
for setting the "Press " key for 5 s to confirm the "cooling offset temperature"; by turning
the dial it is possible to set a temperature offset. The Lightable ring flashes cyan and the
offset appears on the display.
C
2
Display
Viale Vicenza 14
36063 Marostica VI - Italy
www.vimar.com