Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Corghi SP 3000
Summary of Contents for Corghi SP 3000
- Page 1 CORGHI - Dis. 11 - Man. SP3000 - Vers. 2006 SP 3000 4-105474 del 11/06 Cod. fig. 6 Italiano Manuale d’uso + pezzi di ricambio English Operator’s manual + spare parts Français Manuel d’utilisation + rechange Deutsch Betriebsanleitung + Ersatzteillisten Español...
- Page 2 Español total o parcial con cualquier medio (incluidos microfilmes y fotocopias). Las informaciones contenidas en el presente manual pueden sufrir variaciones sin aviso previo. Elaborazione grafica e impaginazione fficio ubblicazioni ecniche SP 3000 - Manuale d’uso + pezzi di ricambio...
-
Page 3: Table Of Contents
BEAD LIFTER SHELF MOUNTING SCHEME ........... 30 MOUNTING/DEMOUNTING THE TYRE ............ 30 Narrow tyre demounting ............... 30 Wide tyre demounting................32 Tyre mounting..................32 PNEUMATIC SCHEME ................. 35 MAINTENANCE .................... 36 DEMOLITION....................36 RECOMMENDED FIRE-EXTINGUISHING DEVICES........ 36 SP 3000 - Operator’s manual + spare parts... -
Page 4: Introduction
WARNING Adhere to the contents of this manual: Corghi S.p.A. declines all liability in the case of uses of the equipment not specifically described in this manual. SP 3000 - Operator’s manual + spare parts... -
Page 5: Transport, Storage And Handling
Machine transport conditions and technical data WARNING The upright kit and the SP 3000 must be Only one operator may work on the equipment transported in their original packing and must at a time. be kept in the same position as indicated on the packing. - Page 6 WARNING When operating or servicing Corghi S.p.A. equi- pment do not wear ties, loose fitting clothes, necklaces, rings or wristwatches that could become entrapped by moving parts. SP 3000 - Operator’s manual + spare parts...
-
Page 7: Main Components And Controls
Working condition (button activated): • Horizontalarm2isblockedmechanically 6. Bead lifter disc by cylinder 7 and bead breaker disc 7. Blocking cylinders penetration is activated at the same 8. Power cylinder time. SP 3000 - Operator’s manual + spare parts... -
Page 8: Upright Kit
SP3000 - Vers. 2006 UPRIGHT KIT fig. 2 SP 3000 BEAD BREAKER UNIT 8. Cilindro di azionamento fig. 1 - UPRIGHT KIT COD. 8-11100122 - SP 3000 BEAD BREAKER UNIT COD. 8-11100123 SP 3000 - Operator’s manual + spare parts... -
Page 9: Installation On: A2005-A2015-A2020-A2025-A2030
• Disconnect regulator filter unit T air hoses and dismantle the unit located on the rear right side of the body (fig. 4); � � • dismantle the lateral hood (fig. 4a); SP 3000 - Operator’s manual + spare parts... - Page 10 •Take entire bead breaker unit P (fig. 6) and insert the nut and lock nut. it on upright F: � � � � � � � � � � � � � �� � � SP 3000 - Operator’s manual + spare parts...
- Page 11 • Reconnect the pipes to restore the pneumatic line by connecting the two previously positio- ned T and V air hoses to the two regulator filter screw lock nut � upright �� ���� SP 3000 - Operator’s manual + spare parts...
-
Page 12: Bead Lifter Shelf Mounting Scheme
For all tyre mounting/demounting procedures not specifically described, refer to the tyre changer operator’s manual. The SP 3000 kit has been designed to make light alloy rim and particularly rigid low profile tyre demounting and mounting operations easier. Follow the steps described below in order to make best use of the features of the accessories mentioned above. - Page 13 GGIO PNEUMATICI BASSI – create a wider clearance between the head and the tyre; • Penetration is automatically deactivated and the bead breaker disc is disengaged by using the ascent control (fig. 11). SP 3000 - Operator’s manual + spare parts...
-
Page 14: Wide Tyre Demounting
(fig. 12) and lift the tyre until the height necessary for releasing the 2nd bead (fig. 13) is reached. The SP 3000 can be conveniently used during � the 1st bead mounting stage in case of low �... - Page 15 If the well is on the upper side, the wheel is to be clamped on the opposite edge with external clamping so as to demount it (fig. 20); • after the bead has been inserted, release clamp A immediately (fig. 18); � SP 3000 - Operator’s manual + spare parts...
- Page 16 � � � SP 3000 - Operator’s manual + spare parts...
-
Page 17: Pneumatic Scheme
� PNEUMATIC SCHEME 4. 5/2 Blocking valve 5. 5/3 Ascent/descent control valve 7. Blocking cylinders 8. Drive cylinder 4-105441 SP 3000 - Operator’s manual + spare parts... -
Page 18: Maintenance
DEMOLITION If the machine is to be scrapped, remove all electrical, electronic, plastic and metal parts and dispose of them separately in accordance with current provisions as prescribed by law. SP 3000 - Operator’s manual + spare parts... - Page 19 �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� SP 3000 - Manual de uso + repuestos...
- Page 20 0068 9004-105314 PERNO ZAPFEN PIVOT 0071 900454832 DISCO STALL. DISK SCHEIBE DISQUE 0072 900261436 PISTONE PISTON KOLBEN PISTON Ø 6 900701684 TUBO PIPE ROHR TUYAU Ø 8 900701683 TUBO PIPE ROHR TUYAU SP 3000 - Manual de uso + repuestos...
- Page 21 CORGHI S.p.A. - Via per Carpi n.9 42015 CORREGGIO - R.E. - ITALY Tel. ++39 0522 639.111 - Fax ++39 0522 639.150 www.corghi.com - info@corghi.com...
Need help?
Do you have a question about the SP 3000 and is the answer not in the manual?
Questions and answers