Table of Contents
Advertisement
Pin
Terminal
Input/
No.
name
Output
-
153 GND
154 NRAMCS2
Output
155 GPIO_44
Input
-
156 VSSUSB
157 GPIO_47
Output
158 GPIO_20
Output
159 CLKON
Output
160 VCC
Input
161 GPO_18
Output
162 GPO_21
Output
163 DATA[12]
Input/
Output
164 DATA[11]
Input/
Output
165 NWE
Output
166 VEXT
Input
167 GPO_11
Output
168 GPO_20
Output
169 DATA[15]
Input/
Output
170 VMEM
Input
171 NADV
Output
172 NGPCS1
Output
173 VMEM
Input
174 GPIO_45
Output
175 GPIO_46
Output
176 DPLUS
Input
177 SIMCLK
Output
178 JTAGEN
Input
179 VEXT
Input
180 GPO_3
Output
181 GPO_4
Output
182 GPO_7
Output
183 GPO_16
Output
184 GPO_17
Output
185 NHWR/NUSB
Output
186 GPO_19
Output
187 NLWR/NLSB
Output
188 NWAIT
Input
189 NRESET
Input
*
190
BURSTCLK
Output
191 NRAMCS1
Output
192 NAUXCS1
Output
193 GPIO_43
Output
CONFIDENTIAL
Description of terminal
Ground
Chip select for SRAM 2
Wakeup mode select
USB ground
Camera module reset
JTAG TDI
13 MHz oscillator power control
signal (VCXOEN)
Core power supply 1.7-1.9V
(VCORE)
SYNTH enable for RF (SYNTHEN)
SYNTH clock output for RF
(SYNTHCLK)
Processor data bus 12
Processor data bus 11
Processor write strobe
SIM power supply 2.4 - 3.3 V
(VINT)
Band select 4 for RF (BS4)
SYNTH data output for RF
(SYNTHDATA)
Processor data bus 15
Memory power supply 2.7 - 3.3 V
(VMEM)
Address latch enable for
flash memory 2
Chip select for flash memory 2
Memory power supply 2.7 - 3.3 V
(VMEM)
Chip select for 4M SRAM
Chip select for sound generator IC
USB D+
System interface clock output
JTAG enable
SIM power supply 2.4 - 3.3 V
(VINT)
Incoming LED OFF control
Mode select 1 for interface IC
Bluetooth module power ON/OFF control
Band select 1 for RF (BS1)
Band select 2 for RF (BS2)
Processor high write strobe
Mode select 3 for interface IC
Processor low write strobe
Processor wait input
System reset input
Not used
Chip select for SRAM 1
Command latch enable for
flash memory 2
Chip select for Camera module
TM200 OTHERS
Pin
Terminal
No.
name
194 VDDUSB
195 GPIO_23
196 SIMDATAIO
197 GPIO_24
198 GPIO_19
199 GPIO_21
200 GPO_2
201 GND
202 GPO_8
203 GPO_9
204 GPO_10
In this unit, the terminal with asterisk mark ( * ) is (open) terminal which
is not connected to the outside.
IC107 VHIEW6671++-1R (EW6671): HALL
Pin
Terminal
Input/Output
No.
name
1
VDD
2
GND
3
OUT
VDD
1
Pulse Regulator
Reg.
Amplifier
Hall cell
IC108 VHIR3112Q26-1L (R3112Q261A): VOLTAGE DETECTOR
Pin
Terminal
Input/
No.
name
Output
1
VDD
-
-
2
GND
3
CD
Input
4
OUT
Output
VDD
1
+
-
VREF
6 - 7
Input/
Description of terminal
Output
Input
USB power supply 2.8 - 3.3 V (VUSB)
Output
SIM interface reset
Input/
SIM interface data input/output
Output
Output
Sound generator IC reset
Output
JTAG TMS
Output
JTAG TDO
Output
Write protect control for flash memory 1
-
Ground
Output
IrDA power ON/OFF control
Output
Band select 3 for RF (BS3)
Output
BUF OFF for main LCD controller
Description of terminal
Input
Input
-
Ground
Output
Output
Output
3
stage
OUTPUT
Schmitt trigger
& Latch
2
GND
Description of terminal
Power supply
Ground
External condenser
connection terminal for delay
Output terminal (L: when output is
detected, H: when output is canceled)
RD
3
CD
3
1
2
4
OUT
2
GND
Advertisement
Table of Contents
