Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for BluStream HEX31WP-TX
Summary of Contents for BluStream HEX31WP-TX
- Page 1 HEX31WP-TX User Manual RevA5 HEX31WP-TX User Manual...
-
Page 2: Table Of Contents
Output On/Off Function Auto Switching USB Type C Surge protection device recommended Mounting the HEX31WP-TX This product contains sensitive electrical components that may be EDID Control damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use... -
Page 3: Introduction
4K input switcher solution delivering HDMI and USB-C inputs up to 70m at 1080p (40m at 4K 60Hz 4:2:0). The HEX31WP-TX features both manual or automated source selection and includes display on / off control via CEC, RS-232 and IR (via compatible HDBaseT™... -
Page 4: Front Panel Description
RS-232 - 3-pin phoenix connector for RS-232 pass through to / from compatible HDBaseT™ Receiver / Matrix products 12V DC Input - 2-pin phoenix connector to connect to Blustream 12V power supply (supplied) IR Receiver Input - 3-pin phoenix connector to connect to Blustream IR Receiver (phoenix block supplied, IR Receiver not supplied) HDBaseT™... -
Page 5: Output On/Off Function
A slow flashing LED for the Output On/Off button indicates that Output Off mode is selected 3) Within 30 seconds, point the IR remote control that you wish to learn at the IR sensor on the HEX31WP-TX and press the respective button on the IR remote control. -
Page 6: Auto Switching
When the HEX31WP-TX is powered via HDBT from a product such as the SW41HDBT switcher, the signal trigger mode must be set to PoC. This must be done via sending the command TRGPOCPWR via RS-232 to the HEX31WP-TX, using the supplied DB9 to phoenix cable and serial software such as Putty, Hercules or SSCOM. -
Page 7: Edid Control
A custom EDID file can be loaded into the HEX31WP-TX. Some custom EDID’s can be found on Blustream’s website, or use a 3rd party EDID tool to create a custom EDID. To load an EDID onto the HEX31WP-TX complete the following steps: 1) Rename the EDID file to be “EDID.bin”... -
Page 8: Rs-232 Configuration
Some other examples that other control systems deploy include \r or 0D (in hex) • Spaces – Blustream commands do not require space between commands unless specified. There may be some programs that require spacing in order to work. - Page 9 HEX31WP-TX USER MANUAL RS-232 Commands Continued... EDID xx DF zz EDID xx DF zz Set Input xx EDID To Default EDID zz xx=[00]: All Input Port, [01...03]: Input Port zz=00: HDMI 1080p@60Hz, Audio 2ch PCM zz=01: HDMI 1080p@60Hz, Audio 5.1ch PCM/DTS/DOLBY zz=02: HDMI 1080p@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD...
- Page 10 HEX31WP-TX USER MANUAL www.blustream.com.au www.blustream.co.uk...
-
Page 11: Specification
NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate. Package Contents HEX31WP-TX • 1 x HEX31WP-TX • 1 x 12V/1A DC Power Supply • 1 x Magnetic Faceplate • 1 x RS-232 to Phoenix Control Cable •... -
Page 12: Fcc Notice
HEX31WP-TX USER MANUAL Certifications FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. - Page 13 www.blustream.com.au...
Need help?
Do you have a question about the HEX31WP-TX and is the answer not in the manual?
Questions and answers