Wep Key Settings; Security Settings; Wpa Security Settings; Eap - Nokia 002B370 User Manual

S e t t i n g s
Select WLAN security settings
WEP key in use — Select the desired WEP key.
•
Authentication type — Select
•

WEP key settings

— Edit the settings for the WEP key.
•
WEP key settings
In the access point settings, select
Select WLAN security settings
WEP encryption — Select the desired WEP encryption key length.
•
WEP key format — Select whether you want to enter the WEP key data in
•
WEP key — Enter the WEP key data.
•
802.1x security settings
In the access point settings, select
802.1x authenticates and authorizes devices to access a wireless network, and prevents access if the authorization process fails.
Select WLAN security settings
WPA/WPA2 — Select

EAP

•
EAP plug-in settings — If you selected
•
access point.
Pre-shared key — If you selected
•
the WLAN to which you connect.
The settings available for editing may vary.

WPA security settings

In the access point settings, select
Select WLAN security settings
WPA/WPA2 — Select EAP
•
EAP plug-in settings — If you select
•
point.
Pre-shared key — If you select
•
WLAN to which you connect.
WPA2 only mode — To enable TKIP encryption, based on transient keys changed often enough to prevent misuse, select
•
Off. All devices in the WLAN must either allow or prevent the use of TKIP encryption.
The settings available for editing may vary.
EAP
Select Tools Settings
> >
The EAP (extensible authentication protocol) plug-ins are used in wireless networks to authenticate wireless devices and
authentication servers, and the different EAP plug-ins make possible the use of various EAP methods (network service).
You can view the EAP plug-ins currently installed in your device (network service).
1. To define the EAP plug-in settings, select
bearer.
2. Select 802.1x or WPA/WPA2
3. Select WLAN security settings
To use an EAP plug-in when you connect to a WLAN using the access point, select the desired plug-in and
The EAP plug-ins enabled for use with this access point have a check mark next to them. To not use a plug-in, select
Disable.
To edit the EAP plug-in settings, select
To change the priority of the EAP plug-in settings, select
plug-ins when connecting to the network with the access point, or
authentication after attempting to use other plug-ins.
See the device help for more information on EAP plugins.

Data call settings

Select Tools Settings
> >
© 2007 Nokia. All rights reserved.
and from the following:
Open or Shared.
WLAN security mode
WEP key settings and from the following:
>
WLAN security mode
and from the following:
(Extensible Authentication Protocol) or
WPA/WPA2
WPA/WPA2 Pre-shared
>
WLAN security mode
and from the following:
(Extensible Authentication Protocol) or
WPA/WPA2 > EAP, select which EAP plug-ins defined in your device to use with the access
WPA/WPA2 Pre-shared
>
Connection Access
> >
Options
as the security mode.
WPA/WPA2 EAP
> >
Options > Edit.
Connection Data call.
> >
> WEP.
ASCII
> 802.1x.
Pre-shared key
> EAP, select which EAP plug-ins defined in your device to use with the
key, enter the shared private key that identifies your device to
> WPA/WPA2.
Pre-shared key
key, enter the shared private key that identifies your device to the
points.
New access point and define an access point that uses WLAN as a data
>
EAP plug-in settings.
>
Options Raise priority
>
Options
>
69
or Hexadecimal format.
(a secret key used for device identification).
(a secret key used for device identification).
to attempt to use the plug-in before other
Lower priority to use this plug-in for network
Options > Enable.
Options
>