Table of Contents
Advertisement
Care and Cleaning
(continued)
Cleaning The housing / Cup
Warming Tray
•
The outer housing can be wiped with a soft,
damp cloth (do not use abrasive agents or
cloths which can scratch the surfaces).
WARNING: DO NOT IMMERSE CORD, PlUG
OR APPlIANCE IN WATER OR ANY OThER
lIQUID.
Cleaning The Drip Tray
•
The drip tray should be removed, emptied
and cleaned at regular intervals, particularly
when the drip tray full indicator is showing
'Empty Me!'
•
Remove the stainless steel grid and pull
the 'Empty Me!' full indicator upwards to
dislodge from the drip tray. Wash with warm
soapy water, using a non-abrasive washing
liquid, rinse and dry thoroughly.
To re-insert the 'Empty Me!' full indicator back
into the drip tray, simply push back into aligning
slots.
WARNING: ThE WATER TANK ShOUlD
NEVER BE REMOVED OR COMPlETElY EMPTIED
DURING DECAlCIFYING.
Decalcifying The Machine
•
After regular use, hard water can cause
mineral build up in and on many of the
inner functioning components, reducing the
brewing flow, power of the machine, and
affecting the quality of coffee.
•
We advise decalcifying the machine on a
regular basis (every 2-3 months) using a
mixture of white vinegar and water.
•
Follow the instructions provided or use the
following as a guide:
Do not clean any of the parts or accessories in
the dishwasher.
16
Diluted solution
•
1 part white vinegar
(for softer water)
•
2 parts cold tap water
Concentrated
•
1 part white vinegar
solution
•
1 part cold tap water
(for harder water)
•
Ensure the 'SELECTOR CONTROL' is in the
'STANDBY' position, the 'POWER' button
is in the 'Off' position and the machine
is switched off at the power outlet and
unplugged.
•
Remove the filter holder and frothing
attachment. Pour the mixture of white
vinegar and water into the water tank.
•
Plug the machine into the power outlet and
switch on.
•
Press the 'POWER' button to the 'On' position
and turn the 'SELECTOR CONTROL' to the
'STANDBY' position.
•
Place a large container under the group
head, and steam wand.
•
When the brewing temperature has been
reached the red 'HEATING' light will switch
off. Turn the 'SELECTOR CONTROL' to the
'ESPRESSO' position to commence pour.
•
Once half the mixture of white vinegar and
water has run through the group head turn
the 'SELECTOR CONTROL' to the 'STANDBY'
position.
•
Set the 'SELECTOR CONTROL' to the 'STEAM'
position and allow the remaining solution
to run through the steam wand. When the
solution has run through, set the 'SELECTOR
CONTROL' back to 'STANDBY' position.
•
After decalcifying, remove the water tank
and rinse thoroughly then re-fill with fresh
cold water. To rinse the machine, repeat
previous steps.
Do not use any other decalcifying agents,
other than vinegar.
Trouble Shooting Guide
PROBlEM
POSSIBlE CAUSES
Coffee does not run through
•
Machine is not turned on or plugged in
•
Water tank is empty
•
Selector control not in 'Espresso' position
•
Coffee grind is too fine
•
Too much coffee in the filter
•
The filter is blocked (see Care and Cleaning)
•
Excessive tamping
Coffee runs out too quickly
•
Coffee grind is too coarse
•
Incorrect quantity of coffee in the filter basket
•
Not firmly tamped
Coffee runs too slowly
•
The water tank is empty or low
•
Coffee grind is too fine
•
Machine is blocked by scale build up (see Care and
Cleaning)
•
Too much coffee in the filter basket.
•
Excessive tamping
Coffee runs out around the edge
•
Filter holder is not inserted in the brew head properly
of the filter holder
•
There are coffee grounds affecting the sealing around the
filter rim
Coffee is too weak or watery
•
Coffee grind is not fine enough (use coffee ground for
espresso machines)
•
Not enough coffee in the filter
•
Incorrect quantity of coffee in the filter basket
•
Not firmly tamped
Coffee is too cold
•
Machine not preheated
•
Cups not preheated
•
Milk not heated enough (if making a cappuccino or latte)
refer to Milk guide
17
Hide quick links:
Advertisement
Table of Contents
