Advertisement
Quick Links
Advertisement
Related Manuals for Shark IW4000 Series
Summary of Contents for Shark IW4000 Series
- Page 1 Shark Cordless Detect Vacuum IW4000 Series OWNER’S GUIDE...
-
Page 2: Table Of Contents
RECORD THIS INFORMATION Cleaning The Sensors ......................17 Model Number: ������������������������������ Checking For Blockages In The Vacuum .................18 Checking For Blockages In The Auto Empty Dock (IW4000 Series Only) ..18 Serial Number: ������������������������������� Date Code: ���������������������������������� Troubleshooting .......................19 Date of Purchase (Keep Receipt): ����������������... -
Page 3: Important Safety Instructions
DO NOT expose any parts of the should, or has been dropped, damaged, left 43. For IW4000 Series use only Shark battery nozzle or hand tool. vacuum to water or other liquids. outdoors, or dropped into water. - Page 4 NOTES AUTO-EMPTY ASSEMBLY (IW4000 SERIES) 1. Slide the Wand onto the neck of the Floor 4. Place the dock on the floor near a wall Nozzle until it clicks into place. outlet. Plug the Power Cord into the outlet, then connect the cord to the port on the 2.
-
Page 5: Charging Your Li-Ion Battery
NOTE: When the unit is docked properly, the charging lights on the battery will blink, indicating that charging has begun. NOTE: The Shark battery, like all lithium-ion batteries, will naturally decrease in capacity over time from the 100% capacity of NOTE: The main unit comes with a partial charge. -
Page 6: Battery Removal
USING YOUR VACUUM BATTERY REMOVAL REMOVING THE BATTERY CONTROLS AND CLEANING MODES POWER UPRIGHT BATTERY When upright, the nozzle will lock to allow Press the button on the UI Screen to for freestanding storage when the hand vac turn on power. To turn off power, press To remove the battery from the hand vacuum, is detached. - Page 7 USING YOUR VACUUM USING YOUR VACUUM USING THE AUTO-EMPTY DOCK (IW4000 SERIES) ABOVE-FLOOR WITH WAND ABOVE-FLOOR WITH HAND VACUUM Detach the hand vacuum to clean above- To detach the floor nozzle from the wand, floor areas. Press the front latch release...
-
Page 8: Maintaining Your Vacuum Cleaner
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM EMPTYING THE DOCK DUST BIN (IW4000 SERIES) CLEANING THE DUST CUP AND FILTER The dock dust bin holds up to 45 days’ worth To empty the bin, hold it over the bin and With the dust cup open and the power off, To deep-clean the dust cup, slide the release of dust and debris (depending on model). -
Page 9: Cleaning The Auto Empty Dock Filter (Iw4000 Series Only)
MAINTAINING YOUR VACUUM MAINTAINING YOUR VACUUM CLEANING THE SENSORS CLEANING THE AUTO-EMPTY DOCK FILTER (IW4000 SERIES) Make sure to clean the Detect sensors Fig. 1 regularly, as hair and other debris may build up and obstruct them. If the sensors are partially obstructed, Clean Sense Detect mode will not function as expected. -
Page 10: Checking For Blockages In The Vacuum
3. Check wand, accessories, and inlet openings and remove any blockages. AUTO-EMPTY DOCK (IW4000 SERIES) and floor nozzle. 4. Allow unit and battery to cool for at least 45 minutes, until they return to room temperature. -
Page 11: Additional Accessories Available
If you further agree to receive communications from us, you can also receive tips and advice on how to get the best out of your Shark appliance and hear the latest news about new Shark technology and launches. - Page 12 NOTES NOTES s h a r kc l e a n . c o . u k s h a r kc l e a n . c o . u k...
- Page 13 Illustrations may differ from actual product. We are constantly striving to improve our products; therefore the specifications contained herein are subject to change without notice. @sharkcleanuk © 2024 SharkNinja Operating LLC. FLOOR DETECT and SHARK are registered trademarks of SharkNinja Operating LLC in the United Kingdom. @sharkcleanuk IW4000UK�18V�IB�MP�...
Need help?
Do you have a question about the IW4000 Series and is the answer not in the manual?
Questions and answers