Table of Contents
Advertisement
.
.
.
.
.
.
.
.
.
.
.
.
.
.
Description
Adjustable parameters
Description
Adjustable parameters
To use MIDI continuous
controller messages to instantly
change the delay time, set Delay
Time Change to the Step setting.
I N S T R U C T I O N
M A N U A L
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3 K D V H U
Twelve-stage, stereo phaser effect.
Phaser Out Level. Adjusts the wet/dry signal ratio. Select between 1.0
/
for 0% wet (no effect) and 10.0 for 100% wet (all effect).
Phaser Rate (Hz). Range: from 0.08 Hz to 10 Hz. Adjusts the rate of
the Phaser effect. The increment of change gradually increases from
0.01 Hz for the slowest rate to 0.08 Hz for the fastest rate. Remember
that the TAP button can always be used to key in the Phaser rate by
feel– two TAPs set the time it takes for the Phaser LFOs (Low Fre-
quency Oscillators) to go through one cycle.
Phaser Depth. Adjusts the width of the Phaser sweep and how appar-
ent the effect sounds. Select between 1.0 for no apparent effect and
10.0 for maximum effect.
Phaser Feedback. Adjusts how much signal from the Phaser effect is
recycled back to the input. Select between 1.0 for minimum levels and
10.0 for maximum levels.
Phaser Stereo. Adjusts the amount of stereo spread in the effect.
Select between 1.0 for mono and 10.0 for maximum stereo spread.
~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~ ~~ ~ ~~ ~~ ~~ ~~ ~~
& R P E L Q D W L R Q ( I I H F W V 7 \ S H V
' H O D \ & K R U X V
Mono Delay plus stereo Triangle Chorus.
FX
Wet Out Level. Adjusts the wet/dry signal ratio. Select between 1.0
/
for 0% wet (no effect) and 10.0 for a 50% mix.
Delay Time (ms). Range: 30 to 1450 milliseconds. Adjusts the time
interval between the delayed repeats. The increment of change gradu-
ally increases from 1 millisecond at the shortest delay time to 10 milli-
seconds at the longest delay time. Remember that the TAP button can
always be used to key in delay times by feel.
Chorus Depth. Adjusts the amount of Doppler shift and how apparent
the Chorus effect sounds. Select between 1.0 for no apparent effect
and 10.0 for maximum effect.
Delay Feedback. Adjusts the number of delay repeats. Select
between 1.0 for a single delay repeat and 10.0 for many repeats.
Chorus Rate (Hz). Range: from 0.08 Hz to 10 Hz. Adjusts the rate of
the chorus effect. The increment of change gradually increases from
0.01 Hz for the slowest rate to 0.08 Hz for the fastest rate.
Delay Time Change. Select Ramp or Step to change the way the
effect responds to changes in the Delay Time parameter. With the
Ramp setting, the delay time change will be gradual with an analog
sounding pitch warble, (audible until the delay time stabilizes). With the
Step setting, the delay time change will be instant with a "digital zip"
sound audible for a moment.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. P r e s e t
39
E d i t
F X
M o d e
Hide quick links:
Advertisement
Table of Contents
