Fender SUPER CHAMP XD Service Manual
  1. Manuals
  2. Brands
  3. Fender Manuals
  4. Amplifier
  5. Super Champ-XD
  6. Service manual

Fender SUPER CHAMP XD Service Manual

Hide thumbs Also See for SUPER CHAMP XD:

Advertisement

Table of Contents

See also: Owner's Manual , Service Diagram
®
SUPER CHAMP
XD
(This is the model name for warranty claims)
p/n 2331100000 (120V)

SERVICE MANUAL

ATTENTION:
WARRANTY SERVICE PROCEDURES
Warranty field service except for tube replacement is not allowed on the Super Champ
XD® Amplifier (See Service Bulletin #SB07-1). Any Dealer or Service Center in
possession of a defective Super Champ® XD with a warrantable defect other than failed
tubes, should contact the Fender Customer Service Support Center to arrange for a re-
placement amplifier. The Support Center can be reached at (800) 345-3642 or by email at
service@fender.com.
THIS TECHNICAL DATA PROVIDED FOR NON-WARRANTY REPAIRS ONLY
Fender Musical Instruments Corporation, 8860 East Chaparral Road Suite 100 Scottsdale, AZ 85250
Issued: October, 2006

Advertisement

Table of Contents
loading

Related Manuals for Fender SUPER CHAMP XD

Summary of Contents for Fender SUPER CHAMP XD

  • Page 1: Service Manual

    Super Champ® XD with a warrantable defect other than failed tubes, should contact the Fender Customer Service Support Center to arrange for a re- placement amplifier. The Support Center can be reached at (800) 345-3642 or by email at service@fender.com.

  • Page 2: Parts List Codes

    Fender® Musical Instruments Corporation. It is Corporation. not to be sold or assigned to another party and is disclosed solely for use by Fender Authorized • Parts marked with two asterisks ( Service Centers for purposes of product service ) indicate the and maintenance.

  • Page 3: Specifications

    50mV for 20 W into 8 ohms @ 5 %THD Impedances Input (Pre-Amp): >1M Ohms Line Out: 1 kOhm Speaker Complement: Fender Special Design, 8 ohm, 10” (P/N 0073858000) Dimensions Height: 15.0 in ( 38 cm) Width: 17.5 in ( 45 cm) Depth: 9.0 in ( 22.9 cm)

  • Page 4: Service Notes

    ® SUPER CHAMP (This is the model name for warranty claims) SERVICE NOTES PCB. Remove all screws holding the main PCB CHASSIS REMOVAL is accomplished by first to the stand offs on the chassis. Then remove removing the cabinet’s upper back panel. Then the front panel knobs and the nuts holding the remove the four (4) screws from the top of the controls to the front panel.

  • Page 5: Circuit Description

    EFFECT SELECT are read via the port ex- Information is focused for its effective use while pander U4 and the data sent to the uDSP system via maintaining the security of Fender® proprietary in- the I C interface lines SCL and SDA.

  • Page 6: Power Supply

    ® SUPER CHAMP (This is the model name for warranty claims) POWER SUPPLY T1 has four secondary windings for the +5V regula- tor, the +/-12V supplies, the tube filaments and the high voltage supply. The violet winding is rectified by a full wave bridge, filtered by C41 and fed to a three terminal regulator to produce 5VDC for the digital circuitry on the main PCB and fed to the uDSP PCB where it is regulated to +3.3.VDC and...

  • Page 7: Parts List

    + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
  • Page 8 + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
  • Page 9 + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
  • Page 10 + * Access to this part or assembly is controlled. Please contact the FMIC Customer Service Department. ** Safety Requirement part. Replacement must match Safety Agency…–Value, if specified –Type, if specified –Approval Mark(s) if on part. shaded + ** Both a unique Fender® part and a Safety Requirement part as defined above.
  • Page 11 ® SUPER CHAMP (This is the model name for warranty claims) Service Diagram List Service Diagram (Schematic) ....SUPER CHAMP XD Service Diagram (PCB Assembly) ....SUPER CHAMP XD...

Table of Contents