FH-P4400
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Japan
Imprimé au Japon
<CRD3248-A> UC
<00B00F0W01>
Connecting the Units
Note:
• When an external power amp is being used with
• This unit is for vehicles with a 12-volt battery and
this system, be sure not to connect the blue/white
negative grounding. Before installing it in a recre-
lead to the amp's power terminal. Likewise, do
ational vehicle, truck or bus, check the battery
voltage.
not connect the blue/white lead to the power ter-
• To avoid shorts in the electrical system, be sure to
minal of the auto-antenna. Such connection could
disconnect the ≠ battery cable before beginning
cause excessive current drain and malfunction.
installation.
• To avoid short-circuiting, cover the disconnected
• Refer to the owner's manual for details on
lead with insulating tape. Especially, insulate the
connecting the power amp and other units, then
unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not insu-
make connections correctly.
lated.
• Secure the wiring with cable clamps or adhesive
• To prevent incorrect connection, the input side of
tape. To protect the wiring, wrap adhesive tape
the IP-BUS connector is blue, and the output side
around them where they lie against metal parts.
is black. Connect the connectors of the same
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake
colors correctly.
and seat rails. Do not route wiring in places that
• If this unit is installed in a vehicle that does not
get hot, such as near the heater outlet. If the insu-
have an ACC (accessory) position on the ignition
lation of the wiring melts or gets torn, there is a
switch, the red lead of the unit should be connect-
danger of the wiring short-circuiting to the vehicle
ed to a terminal coupled with ignition switch
body.
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
• Don't pass the yellow lead through a hole into the
from the vehicle for several hours. (Fig. 1)
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing fuse, be sure to use only fuse of
ACC position
No ACC position
the rating prescribed on the fuse holder.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right ≠ speaker leads are common.
• Speakers connected to this unit must be high-
• The black lead is ground. Please ground this lead
power types with minimum rating of 40 W and
separately from the ground of high-current prod-
impedance of 4 to 8 ohms. Connecting speakers
ucts such as power amps.
with output and/or impedance values other than
If you ground the products together and the
those noted here may result in the speakers catch-
ground becomes detached, there is a risk of dam-
ing fire, emitting smoke, or becoming damaged.
age to the products or fire.
• When this product's source is switched ON, a
• Cords for this product and those for other prod-
control signal is output through the blue/white
ucts may be different colors even if they have the
lead. Connect to an external power amp's system
same function. When connecting this product to
remote control or the car's Auto-antenna relay
another product, refer to the supplied Installation
control terminal (max. 300 mA 12 V DC). If the
manuals of both products and connect cords that
car features a glass antenna, connect to the anten-
have the same function.
na booster power supply terminal.
Antenna jack
This Product
Subwoofer output
Multi-CD player
(sold separately)
IP-BUS input (Blue)
Yellow
Fuse holder
To terminal always supplied with power
regardless of ignition switch position.
Red
Fuse resistor
To electric terminal controlled by
Fig. 1
ignition switch (12 V DC) ON/OFF.
Orange
Fuse resistor
To lighting switch terminal.
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Perform these connections when using a
different amp (sold separately).
Front output
Rear output
Connecting cords
with RCA pin plugs
(sold separately)
Blue/white
To system control terminal of the power
amp or Auto-antenna relay control
terminal (max. 300 mA 12 V DC).
System remote control
+
+
Front speaker
≠
≠
White
Gray
+
+
Front speaker
≠
≠
White/black
Gray/black
Left
Green
Violet
+
+
Rear speaker
≠
≠
Green/black
Violet/black
+
+
Rear speaker
≠
≠
+
+
Subwoofer
≠
≠
<ENGLISH>
Power amp
(sold separately)
Power amp
(sold separately)
Power amp
(sold separately)
Front speaker
Front speaker
Right
Rear speaker
Rear speaker
Subwoofer
Fig. 2