Pioneer FH-P4200MP Installation Manual

FH-P4200MP
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit
est conforme à CEMA.
Printed in China
Imprimé en Chine
<YRD5034-A/U> UC <KMINX> <04J00001>
Connecting the Units
Note:
• When an external power amp is being used with
• This unit is for vehicles with a 12-volt battery and
this system, be sure not to connect the blue/white
negative grounding. Before installing it in a recre-
lead to the amp's power terminal. Likewise, do
ational vehicle, truck or bus, check the battery
voltage. not connect the blue/white lead to the power ter-
• To avoid shorts in the electrical system, be sure to minal of the auto-antenna. Such connection could
disconnect the ≠ battery cable before beginning cause excessive current drain and malfunction.
installation. • To avoid a short-circuit, cover the disconnected
• Refer to the owner's manual for details on lead with insulating tape. Insulate the unused
connecting the power amp and other units, then speaker leads without fail. There is a possibility of
a short-circuit if the leads are not insulated.
make connections correctly.
• To prevent incorrect connection, the input side of
• Secure the wiring with cable clamps or adhesive
the IP-BUS connector is blue, and the output side
tape. To protect the wiring, wrap adhesive tape
is black. Connect the connectors of the same
around them where they lie against metal parts.
colors correctly.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake, • This unit can not be installed in a vehicle that
and seat rails. Do not route wiring in places that does not have an ACC (accessory) position on
get hot, such as near the heater outlet. If the insu- the ignition switch. (Fig. 1)
lation of the wiring melts or gets torn, there is a
danger of the wiring short-circuiting to the vehicle
body.
• Don't pass the yellow lead through a hole into the
engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
ACC position No ACC position
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing the fuse, be sure to only use a
• The black lead is ground. Please ground this lead
fuse of the rating prescribed on this unit.
separately from the ground of high-current prod-
• Since a unique BPTL circuit is employed, never
ucts such as power amps.
wire so the speaker leads are directly grounded or
If you ground the products together and the
the left and right ≠ speaker leads are common.
ground becomes detached, there is a risk of dam-
• If the RCA pin jack on the unit will not be used,
age to the products or fire.
do not remove the caps attached to the end of the
connector.
• Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers catching
• Cords for this product and those for other prod-
fire, emitting smoke or becoming damaged.
ucts may be different colors even if they have the
• When this product's source is switched ON, a
same function. When connecting this product to
control signal is output through the blue/white
another product, refer to the supplied manuals of
lead. Connect to an external power amp's system
both products and connect cords that have the
remote control or the car's Auto-antenna relay
same function.
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
15 cm (5-7/8 in.)
Front output
(FRONT OUTPUT)
Subwoofer output or nonfading output
Antenna jack This Product
IP-BUS input (Blue)
Yellow/black
If you use an equipment with Mute function, wire this lead
to the Audio Mute lead on that equipment. If not, keep the
Audio Mute lead free of any connections.
Fig. 1
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
Orange/white
To lighting switch terminal.
Black (ground)
With a 2 speaker system, do not connect
To vehicle (metal) body.
anything to the speaker leads that are not
This terminal may or connected to speakers.
may not be included.
Perform these connections when using
the optional amplifier.
Connecting cords
with RCA pin plugs
(sold separately)
Fuse IP-BUS cable
Multi-CD player
(sold separately)
System remote control
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
+
Front speaker
≠
White Gray
+
Front speaker
≠
White/black Gray/black
Left
Green Violet
+
Rear speaker
≠
Green/black Violet/black
+
Subwoofer or
Rear speaker
≠
<ENGLISH>
Power am p
(sold separately)
Power amp
(sold separately)
+
Front speaker
≠
+
Front speaker
≠
Right
+
Rear speaker
≠
+
Subwoofer or
Rear speaker
≠
Fig. 2