Subscribe to Our Youtube Channel
Related Manuals for BCM EPX-ASLP
Summary of Contents for BCM EPX-ASLP
- Page 1 EPX-ASLP Intel® Processor N-series & Atom® Processor X Series BGA Processor Pico ITX Motherboard User’s Manual Ed – 26 November 2024 Copyright Notice Copyright © 2024 ALL RIGHTS RESERVED. Part No: E2047EPAS00R...
-
Page 2: Document Amendment History
EPX-ASLP User’s Manual Document Amendment History Revision Date Comment November 2024 Initial Release 2 EPX-ASLP User’s Manual... -
Page 3: Declaration Of Conformity
Microsoft Windows is registered trademark of Microsoft Corp. All other product names or trademarks are properties of their respective owners. Disclaimer This manual is intended to be used as a practical and informative guide only and is subject EPX-ASLP User’s Manual... - Page 4 ㆍProduct name and serial number ㆍDescription of your peripheral attachments ㆍDescription of your software (operating system, version, application software, etc.) ㆍA complete description of the problem ㆍThe exact wording of any error messages 4 EPX-ASLP User’s Manual...
- Page 5 On the other hand, if the new product defect is resulting from incorrect configuration or erroneous use by the user instead of any problem of the hardware itself, the customer will also be requested to pay for relevant handling fees. EPX-ASLP User’s Manual...
- Page 6 Lacking detailed statement of fault steps also makes the problem hard to be identified, sometimes resulting in second-time repairs. 6 EPX-ASLP User’s Manual...
- Page 7 • Product has been altered or its label of the serial number has been torn off. • Product functionality issues resulting from improper use by the user, unauthorized dismantle or alteration, unfit operation environment, improper maintenance, accident EPX-ASLP User’s Manual...
- Page 8 If the customer demands an additional maintenance analysis report, a service fee of various level will be charged depending on the warranty status. In case the analysis result shows that the defect attributes to our faulty design or process, the analysis fee will be exempted. 8 EPX-ASLP User’s Manual...
- Page 9 9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to EPX-ASLP User’s Manual...
- Page 10 The equipment has obvious signs of breakage. 14. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. 15. Equipment intended only for use in a RESTRICTED ACCESS AREA. 10 EPX-ASLP User’s Manual...
- Page 11 A NOTE provides additional information intended to avoid Note inconveniences during operation. Direct current. Alternating current Stand-by, Power on FCC Certification CE Certification Follow the national requirements for disposal of equipment. Stacking layer limit This side up EPX-ASLP User’s Manual 11...
- Page 12 EPX-ASLP User’s Manual Fragile Packaging Beware of water damage, moisture-proof Carton recyclable Handle with care Follow operating instructions of consult instructions for use. 12 EPX-ASLP User’s Manual...
- Page 13 EXPLOSION ou une fuite de liquide ou de gaz inflammable. - UNE BATTERIE soumise à une pression d'air extrêmement basse pouvant entraî ner une EXPLOSION ou une fuite de liquide ou de gaz inflammable. EPX-ASLP User’s Manual 13...
-
Page 14: Table Of Contents
Install Serial IO Driver ..................... 42 4.BIOS Setup ........................43 Introduction ......................44 Starting Setup ......................44 Using Setup ......................45 Getting Help ......................46 In Case of Problems ....................46 BIOS setup ......................47 4.6.1 Main Menu ............................47 14 EPX-ASLP User’s Manual... - Page 15 4.6.3.2.1.4 PCI Express Root Port 12 (M.2 KeyB) .................. 68 4.6.3.2.2 SATA Configuration ....................... 69 4.6.3.2.3 HD Audio Configuration ......................69 4.6.3.3 Board & Panel Configuration ..................... 70 4.6.4 Security............................72 4.6.4.1 Secure Boot ..........................72 EPX-ASLP User’s Manual 15...
- Page 16 EPX-ASLP User’s Manual 4.6.5 Boot ..............................73 4.6.6 Save and Exit ..........................74 5. Mechanical Drawing ....................75 6. Maintenance & Troubleshooting ................77 16 EPX-ASLP User’s Manual...
-
Page 17: Getting Started
1.2 Packing List Before installation, please ensure all the items listed in the following table are included in the package. Item Description Q’ty EPX-ASLP mainboard Desiccant (5g) SATA cable (35cm) SATA power cable (20cm) M.2 Screw M.2 Stand-Off EPX-ASLP User’s Manual 17... -
Page 18: Manual Objectives
We strongly recommend that you study this manual carefully before attempting to set up EPX-ASLP or change the standard configurations. Whilst all the necessary information is available in this manual we would recommend that unless you are confident, you contact your supplier for guidance. -
Page 19: System Specifications
Intel® Alder Lake N: Intel® Processor N97 Intel® Amston Lake (Alder Lake N Extension) Intel Atom® x7000RE series processors *Design for core count 2 & 4 CPU only. CPU By BOM optional Bottom Layer Soldered Processor EPX-ASLP User’s Manual 19... - Page 20 1 x 2 x 5 pin, pitch 1.27mm connector for RS-232 (via ASIX_AX3243) 1 x 2 x 6 pin, pitch 1.27mm connector for 4 USB 2.0, +5VSB/0.5A (JUSB1) GPIO 1 x 1 x 6 pin, pitch 1.25mm connector for GPIO: 4bits (JDIO1) 20 EPX-ASLP User’s Manual...
- Page 21 10/100/1000 Base-Tx GbE compatible LAN Spec. 2.5 Gigabit Ethernet Max. 2.5G LAN Port ACT/LINK SPEED Definition Definition LED Indicator Light Off No Link Solid Orange 2.5G Solid Yellow Connection Solid Green 1G/100M Yellow Flashing Activity Light Off EPX-ASLP User’s Manual 21...
- Page 22 Test Fh : Vibration broadband random Test 1. PSD: 0.00454G²/Hz, 1.5 Grms 2. Operation mode 3. Test Frequency : 5-500Hz 4. Test Axis : X,Y and Z axis 5. 30 minutes per each axis 6. IEC 60068-2-64 Test:Fh 22 EPX-ASLP User’s Manual...
- Page 23 Reference ISTA 2A, Method : IEC-60068-2-32 Test: Ed Drop Test Drop Test 1 One corner , three edges, six faces 2 ISTA 2A, IEC-60068-2-32 Test:Ed OS Information Win11 64bit, Linux Note: Specifications are subject to change without notice. EPX-ASLP User’s Manual 23...
-
Page 24: Architecture Overview-Block Diagram
EPX-ASLP User’s Manual 1.5 Architecture Overview—Block Diagram The following block diagram shows the architecture and main components of EPX-ASLP. 24 EPX-ASLP User’s Manual... -
Page 25: Hardware Configuration
User’s Manual 2. Hardware Configuration EPX-ASLP User’s Manual 25... -
Page 26: Product Overview
EPX-ASLP User’s Manual 2.1 Product Overview 26 EPX-ASLP User’s Manual... -
Page 27: Jumper And Connector List
Serial port 1 connector 5 x 2 header, pitch 1.27mm JCOM2 Serial port 2 connector 5 x 2 header, pitch 1.27mm JDIO1 General purpose I/O connector 6 x 1 header, pitch 1.25mm M2E1 M.2 KEY-E 2230 connector EPX-ASLP User’s Manual 27... - Page 28 JSPI_EC connector 10 x 1 wafer, pitch 1.00 mm JLVDS1 LVDS connector 15 x 2 wafer, pitch 1.00mm SATAPW1 SATA Power connector 2 x 1 wafer, pitch 2.00mm SODIMM1 DDR5 SODIMM socket DCIN1 DC Power-in connector 28 EPX-ASLP User’s Manual...
-
Page 29: Setting Jumpers & Connectors
AT/ATX/Clear CMOS mode selector (AT_CMOS1) SW DIP1 AT/ATX mode AT mode* ATX mode * Default SW DIP2 Clear CMOS mode Normal* Clear CMOS Note: Switching back SW DIP2 as On for Normal after CMOS clear process is done. EPX-ASLP User’s Manual 29... -
Page 30: Sim Card Slot (Jsim1)
EPX-ASLP User’s Manual 2.3.2 SIM card slot (JSIM1) Signal SIM_DET UIM_DATA UIM_CLK UIM_RESET +VCC_SIM 2.3.3 ESPI connector (JESPI1) Signal PIN PIN Signal ESPI_IO0_CN +V3.3_ESPI ESPI_IO1_CN PLT_BUF_RST# ESPI_IO2_CN ESPI_CS#0 ESPI_IO3_CN ESPI_CLK_CN ESPI_CS#1 ESPI_RST# ESPI_ALERT#1 30 EPX-ASLP User’s Manual... -
Page 31: Serial Port 1 Connector (Jcom1)
2.3.4 Serial port 1 connector (JCOM1) Signal PIN PIN Signal COM_RI#_1 COM_CTS#_1 COM_RTS#_1 COM_DSR#_1 COM_DTR#_RXN_1 COM_TXD_RXP_1 COM_RXD#_TXP_1 COM_DCD#_TXN_1 2.3.5 Serial port 2 connector (JCOM2) Signal PIN PIN Signal COM_RI#_2 COM_CTS#_2 COM_RTS#_2 COM_DSR#_2 COM_DTR#_2 COM_TXD_2 COM_RXD#_2 COM_DCD#_2 EPX-ASLP User’s Manual 31... -
Page 32: General Purpose I/O Connector (Jdio1)
EPX-ASLP User’s Manual 2.3.6 General purpose I/O connector (JDIO1) Signal EC_DI1 EC_DI0 EC_DO1 EC_DO0 +3.3V 2.3.7 USB connector (JUSB1) Signal PIN PIN Signal +V5A_USB5~8 USB_R_DP8 USB_R_DP7 USB_R_DN8 USB_R_DN7 USB_R_DP6 USB_R_DP5 USB_R_DN6 USB_R_DN5 +V5A_USB5~8 32 EPX-ASLP User’s Manual... -
Page 33: Sata Power Connector (Satapw1)
User’s Manual 2.3.8 SATA Power connector (SATAPW1) Signal +V5S_SATA- 2.3.9 Front Panel connector 1 (JFP1) Signal PIN PIN Signal EXT_SYSRST# EXT_PWRBTN# HDD_LED- PWR_LED- HDD_LED+ PWR_LED+ EPX-ASLP User’s Manual 33... -
Page 34: Cpu Fan Connector (Jcpu_Fan1)
EPX-ASLP User’s Manual 2.3.10 CPU fan connector (JCPU_FAN1) Signal CPU_FANOUT CPUFAN_TH +12V +12V 2.3.11 Battery connector (JBT1) Signal +V3.3A_RTC 34 EPX-ASLP User’s Manual... -
Page 35: Lvds Connector (Jlvds1)
User’s Manual 2.3.12 LVDS connector (JLVDS1) Signal PIN PIN Signal +V3.3_LVDS +V5_LVDS + V3.3_LVDS +V5_LVDS LVDS_DATA1_P LVDS_DATA0_P LVDS_DATA1_N LVDS_DATA0_N LVDS_DATA3_P LVDS_DATA2_P LVDS_DATA3_N LVDS_DATA2_N LVDS_BKLTEN LVDS_CLK1_P VBRIGHT LVDS_CLK1_N +12V +12V EPX-ASLP User’s Manual 35... -
Page 36: Jspi_Ec Connector (Jspi_Ec1)
EPX-ASLP User’s Manual 2.3.13 JSPI_EC connector (JSPI_EC1) Signal EC_SMDAT_DBG EC_SMCLK_DBG SPI_HOLD# SPI_ROM_MOSI SPI_ ROM_MISO SPI_ ROM_CLK SPI_ ROM_CS# +V3.3A_SPI 36 EPX-ASLP User’s Manual... -
Page 37: Drivers Installation
Enter to find all the relevant software, utilities, and documentation. Note: Installation procedures and screen shots in this section are for your reference and may not be exactly the same as shown on your screen. EPX-ASLP User’s Manual 37... -
Page 38: Install Chipset Driver
Windows 10 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Install. Step1. Click Next. Step 4. Click Finish to complete setup. Step 2. Click Accept. 38 EPX-ASLP User’s Manual... -
Page 39: Install Vga Driver
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Start. Step 1. Click Begin installation. Step 4. Click Finish to complete setup. Step 2. Click I agree. EPX-ASLP User’s Manual 39... -
Page 40: Install Ethernet Driver
All drivers can be found on the Website. Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 1. Click OK to continue installation. Step 2. Setup completed. 40 EPX-ASLP User’s Manual... -
Page 41: Install Csme Driver
Note: The installation procedures and screen shots in this section are based on Windows 10 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Finish to complete setup. Step 2. Click Next. EPX-ASLP User’s Manual 41... -
Page 42: Install Serial Io Driver
Windows 10 operation system. Step 3. Click Next. Step 1. Click Next to continue installation. Step 4. Click Next. Step 2. Click Next. Step 5. Click Finish to complete setup. 42 EPX-ASLP User’s Manual... -
Page 43: Bios Setup
User’s Manual 4.BIOS Setup EPX-ASLP User’s Manual 43... -
Page 44: Introduction
If the message disappears before you respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the "RESET" button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys. 44 EPX-ASLP User’s Manual... -
Page 45: Using Setup
Note: Some of the navigation keys differ from one screen to another. • To Display a Sub Menu Use the arrow keys to move the cursor to the sub menu you want. Then press <Enter>. A “➢” pointer marks all sub menus. EPX-ASLP User’s Manual 45... -
Page 46: Getting Help
BIOS Vendor and your systems manufacturer to provide the absolute maximum performance and reliability. Even a seemingly small change to the chipset setup has the potential for causing you to use the override. 46 EPX-ASLP User’s Manual... -
Page 47: Bios Setup
However, if the M/B CPU is Alder Lake-N programmed with Amston Lake BIOS(ASL), it can boot up, but there is no guarantee that all functions will work. 4.6.1 Main Menu This section allows you to record some basic hardware configurations in your computer and set the system clock. EPX-ASLP User’s Manual 47... -
Page 48: System Language
Note: The BIOS setup screens shown in this chapter are for reference purposes only, and may not exactly match what you see on your screen. 4.6.2 Advanced Menu This section allows you to configure your CPU and other system devices for basic operation through the following sub-menus. 48 EPX-ASLP User’s Manual... -
Page 49: Cpu Configuration
Vanderpool Technology Enabled[Default] Technology. All[Default] Number of E-cores to enable in each processor package. Note: Number of Cores and E-cores are Active Efficient-cores looked at together. When both are {0,0}, Pcode will enable all cores. EPX-ASLP User’s Manual 49... -
Page 50: Efficient-Core Information
EPX-ASLP User’s Manual 4.6.2.1.1 Efficient-core Information 4.6.2.2 Power & Performance 50 EPX-ASLP User’s Manual... -
Page 51: Cpu - Power Management Control
P-states. Disabled Enable/Disable processor Turbo Mode (requires Turbo Mode Enabled[Default], EMTTM enabled too). AUTO means enabled. Disabled Enable/Disable CPU Power Management. Allows CPU C States Enabled[Default], to go to C States when it’s not 100% utilized. EPX-ASLP User’s Manual 51... -
Page 52: View/Configure Turbo Options
EPX-ASLP User’s Manual 4.6.2.2.1.1 View/Configure Turbo Options 4.6.2.3 PCH-FW Configuration Item Option Description Disabled When Disabled ME will be put into ME Temporarily ME State Enabled[Default], Disabled Mode. 52 EPX-ASLP User’s Manual... -
Page 53: Firmware Update Configuration
Description Selects TPM device: PTT or dTPM. PTT-Enables PTT in dTPM SkuMgr dTPM1.2 – Disables PTT in SkuMgr Warning! TPM Device Selection PTT[Default], PTT/dTPM will be disabled and all data saved on it will be lost. EPX-ASLP User’s Manual 53... -
Page 54: Trusted Computing
O.S. will not show Security Device. TCG EFI protocol Enable[Default] and INT1A interface will not be available. 4.6.2.5 ACPI Settings Item Options Description Disabled Enables or Disables System ability to Hibernate Enable Hibernation Enabled[Default], (OS/S4 Sleep State). This option may not be 54 EPX-ASLP User’s Manual... -
Page 55: It5782 Super Io Configuration
You can use this item to set up or change the Super IO configuration for serial ports. Please refer to 4.6.2.7.1 ~ 4.6.2.7.2 for more information. Item Description Serial Port 1 Configuration Set Parameters of Serial Port 1 (COMA). Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB). EPX-ASLP User’s Manual 55... -
Page 56: Serial Port 1 Configuration
UART 232 422 485 UART 422 Change the Serial Port as RS232/422/485 UART 485 AUTO[Default] Non INT + EXT R INT_EXT R Mode INT R Change the INT_EXT as Auto/INT/EXT EXT R INT + EXT R 56 EPX-ASLP User’s Manual... -
Page 57: Serial Port 2 Configuration
4.6.2.6.2 Serial Port 2 Configuration Item Option Description Disabled Serial Port Enable or Disable Serial Port (COM). Enabled[Default], 4.6.2.7 EC 5782 HW Monitor Item Options Description Enabled, Smart Fan Function Enables or Disables Smart Fan. Disabled[Default] EPX-ASLP User’s Manual 57... -
Page 58: S5 Rtc Wake Settings
Fixed Time, system will wake on the hr::min::sec Wake system from S5 Fixed Time specified. Select Dynamic Time , System will wake on the Dynamic Time current time + Increase minute(s). 4.6.2.9 Serial Port Console Redirection 58 EPX-ASLP User’s Manual... -
Page 59: Usb Configuration
5 sec The time-out value for Control, Bulk, and USB transfer time-out 10 sec Interrupt transfers. 20 sec[Default] 10 sec 20 sec[Default] USB mass storage device Start Unit command Device reset time-out 30 sec time-out. 40 sec EPX-ASLP User’s Manual 59... -
Page 60: Network Stack Configuration
Optical drives are emulated as ‘CDROM’, drives with no media will be Hard Disk CD-ROM emulated according to a drive type. 4.6.2.11 Network Stack Configuration Item Options Description Enabled Network Stack Enable/Disable UEFI Network Stack. Disabled[Default] 60 EPX-ASLP User’s Manual... -
Page 61: Nvme Configuration
User’s Manual 4.6.2.12 NVMe Configuration 4.6.2.13 Inter(R) Ethernet Controller I226-V – 00:04:5F:96:D1:F3 EPX-ASLP User’s Manual 61... -
Page 62: Inter(R) Ethernet Controller I226-V - 00:04:5F:96:D1:F4
EPX-ASLP User’s Manual 4.6.2.14 Inter(R) Ethernet Controller I226-V – 00:04:5F:96:D1:F4 4.6.3 Chipset 62 EPX-ASLP User’s Manual... -
Page 63: System Agent (Sa) Configuration
User’s Manual 4.6.3.1 System Agent (SA) Configuration Item Option Description Enabled VT-d VT-d capability. Disabled[Default] 4.6.3.1.1 Memory Configuration Item Option Description Disabled[Default] Enable/Disable In-Band ECC. Will be enabled if In-Band ECC Support Enabled memory has symmetric configuration EPX-ASLP User’s Manual 63... -
Page 64: Graphics Configuration
128MB Select the Aperture Size Note : Above 4GB MMIO BIOS 256MB[Default] assignment is automatically enabled when selecting > Aperture Size 512MB 2048MB aperture. To use this feature, please disable 1024MB CSM Support. 4.6.3.2 PCH-IO Configuration 64 EPX-ASLP User’s Manual... -
Page 65: Pci Express Configuration
PCI Express Root Port 7 Disabled Control the PCI Express Root Port. (LAN1-I226) Enabled[Default], Set the ASPM Level: Force L0s – Force all links Disabled[Default], to L0s State AUTO – BIOS auto configure ASPM DISABLE – Disables ASPM. Auto EPX-ASLP User’s Manual 65... -
Page 66: Pci Express Root Port 9 (M.2 Keye)
L0s State AUTO – BIOS auto configure ASPM DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], Enable/Disable Precision Time Measurement Enabled Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 66 EPX-ASLP User’s Manual... -
Page 67: Pci Express Root Port 10 (Lan2-I226)
L0s State AUTO – BIOS auto configure ASPM DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], Enable/Disable Precision Time Measurement Enabled Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 EPX-ASLP User’s Manual 67... -
Page 68: Pci Express Root Port 12 (M.2 Keyb)
L0s State AUTO – BIOS auto configure ASPM DISABLE – Disables ASPM. Auto Disabled[Default] L1 Substates L1.1 PCI Express L1 Substates settings. L1.1 & L1.2 Disabled[Default], Enable/Disable Precision Time Measurement Enabled Auto[Default] Gen1 PCIe Speed Configure PCIe Speed. Gen2 Gen3 68 EPX-ASLP User’s Manual... -
Page 69: Sata Configuration
User’s Manual 4.6.3.2.2 SATA Configuration Item Options Description Enabled[Default] SATA Controller(s) Enable/Disable SATA Device. Disabled, Enabled[Default] Port 0/1 Enable or Disable SATA Port. Disabled 4.6.3.2.3 HD Audio Configuration EPX-ASLP User’s Manual 69... -
Page 70: Board & Panel Configuration
CH7511 EDID Panel Option 1366x768 18/1 Option. 1024x600 18/1 1280x800 18/1 1366x768 24/1 Panel Brightness Control BIOS[Default] Panel Brightness Control Method. 1.BIOS Method OS Driver 2.OS Driver. Panel Brightness Select Panel back light PWM duty. 100%[Default] 70 EPX-ASLP User’s Manual... - Page 71 30 sec 40 sec 50 sec Watch Dog Select WatchDog. 1 min 2 min 10 min 30 min Disabled Enable/Disabled USB Standby Power USB Standby Power Enabled[Default] during S3/S4/S5. Disabled[Default] SHOW DMI INFO SHOW DMI INFO Enabled EPX-ASLP User’s Manual 71...
-
Page 72: Security
EPX-ASLP User’s Manual 4.6.4 Security ⚫ Administrator Password Set setup Administrator Password ⚫ User Password Set User Password 4.6.4.1 Secure Boot 72 EPX-ASLP User’s Manual... -
Page 73: Boot
Setup Prompt Timeout 1~ 65535 key. 65535(0xFFFF) means indefinite waiting. On[Default] Bootup NumLock State Select the keyboard NumLock state Disabled[Default] Quiet Boot Enables or disables Quiet Boot option Enabled Boot Option #1 Set the system boot order. EPX-ASLP User’s Manual 73... -
Page 74: Save And Exit
EPX-ASLP User’s Manual 4.6.6 Save and Exit 74 EPX-ASLP User’s Manual... -
Page 75: Mechanical Drawing
User’s Manual 5. Mechanical Drawing EPX-ASLP User’s Manual 75... - Page 76 EPX-ASLP User’s Manual Unit: mm 76 EPX-ASLP User’s Manual...
-
Page 77: Maintenance & Troubleshooting
System Maintenance Introduction If the components of the product fail they must be replaced. Please contact the system reseller or vendor to purchase the replacement parts. Please follow the safety precautions outlined in the sections that follow EPX-ASLP User’s Manual 77... - Page 78 This equipment is not suitable for use in locations where children are likely to be present. DO NOT: ⚫ Drop the device. ⚫ In a site where the ambient temperature exceeds the rated temperature. 78 EPX-ASLP User’s Manual...
- Page 79 This reduces the possibility of ESD damage. ⚫ Only handle the edges of the electrical component. When handling the electrical component, hold the electrical component by its edges. Please ensure the following safety precautions are adhered to at all times. EPX-ASLP User’s Manual 79...
- Page 80 Never drop any objects or liquids through the openings of the device. ⚫ Be cautious of any possible allergic reactions to solvents or chemicals used when cleaning the device. ⚫ Avoid eating, drinking and smoking within vicinity of the device. 80 EPX-ASLP User’s Manual...
- Page 81 No Console Input Devices are found Flash update is failed Typically for development use. The beep code is generated when platform cannot be reset because reset protocol is not available. Platform PCI resource requirements cannot be met EPX-ASLP User’s Manual 81...
Need help?
Do you have a question about the EPX-ASLP and is the answer not in the manual?
Questions and answers