Advertisement
Quick Links
Fokker E.III Slow Flyer
Specifications:
Wingspan: 450 mm / 17.71 INCH
-
Wing Area: 3 sq dm / 0.32 sq ft
-
Flying Weight: 40 g / 1.41 oz.
-
Fuselage Length: 300 mm / 11.81 INCH
-
Scale: 1:20
-
Required Electronics
RC - Transmitter with at least 4 Channels
-
1 x Mini Receiver MXL-RX42
-
2 x Servo (ca. 2 g)
-
1 x 8520 Coreless Motor
-
1 x 138 mm Propeller
-
1 x Battery (ca. 150 mAh)
-
©Sebastian Hansen
1
Advertisement
Related Manuals for Tony Ray's AeroModel Fokker E.III Slow Flyer
Summary of Contents for Tony Ray's AeroModel Fokker E.III Slow Flyer
- Page 1 Fokker E.III Slow Flyer Specifications: Wingspan: 450 mm / 17.71 INCH Wing Area: 3 sq dm / 0.32 sq ft Flying Weight: 40 g / 1.41 oz. Fuselage Length: 300 mm / 11.81 INCH Scale: 1:20 Required Electronics RC - Transmitter with at least 4 Channels 1 x Mini Receiver MXL-RX42 2 x Servo (ca.
- Page 2 BEFORE YOU BEGIN Tips and Tricks 1. Read through the manual before you begin, thus you will have an overall idea of what to 2. Check all parts in the scope of delivery list. If you find any serious defects or missing parts, please contact Tony and Sebastian directly.
- Page 3 Kit Inventory Wood Sheets: 4 x Balsa Wood Sheet, 1 x Plywood Sheet Hardware Parts: 2 x Carbon Rod, 8 x Magnets, 1 x Fleece-Hinges, 4 x Screws, 2 x Rubber Part for Wheels, 1 x Heat Shrink Tube, 1 x Wings Drawing, Covering Tissue ©Sebastian Hansen...
- Page 4 Part 1: Fuselage Step 1: 3 x Magnet. ©Sebastian Hansen...
- Page 5 Step 4: Wet this side using water. ©Sebastian Hansen...
- Page 6 Step 6: Sand the edge carefully. ©Sebastian Hansen...
- Page 7 ©Sebastian Hansen...
- Page 8 ©Sebastian Hansen...
- Page 9 Step 11: 3 x Magnet. Step 12: Please pay attention to the polarity of the magnets! ©Sebastian Hansen...
- Page 10 ©Sebastian Hansen...
- Page 11 Step 16: Wet this side using water. ©Sebastian Hansen...
- Page 12 Step 17: Wet this side using water. Step 18: Sand the edges carefully. ©Sebastian Hansen...
- Page 13 Step 19: Sand these edges carefully. ©Sebastian Hansen...
- Page 14 Step 21: Magnet Holder. ©Sebastian Hansen...
- Page 15 ©Sebastian Hansen...
- Page 16 ©Sebastian Hansen...
- Page 17 ©Sebastian Hansen...
- Page 18 Step 30: Cut them off. ©Sebastian Hansen...
- Page 19 ©Sebastian Hansen...
- Page 20 ©Sebastian Hansen...
- Page 21 Step 36: Carbon Rod, Hot Shrink Tube. ©Sebastian Hansen...
- Page 22 Step 37: Do not bond the carbon rod and hot shrink tube using glue! ©Sebastian Hansen...
- Page 23 ©Sebastian Hansen...
- Page 24 ©Sebastian Hansen...
- Page 25 ©Sebastian Hansen...
- Page 26 ©Sebastian Hansen...
- Page 27 Step 47: Carbon Rod. ©Sebastian Hansen...
-
Page 28: Part 2: Landing Gear
Part 2: Landing Gear Step 49: Carbon Rod. ©Sebastian Hansen... - Page 29 ©Sebastian Hansen...
- Page 30 Step 53: You can use carbon rod to strengthen here. Step 54: Rubber wheel. ©Sebastian Hansen...
- Page 31 Step 55: Make sure the texture is vertical. ©Sebastian Hansen...
- Page 32 Step 57: Hot Shrink Tube. ©Sebastian Hansen...
-
Page 33: Part 3: The Wings
Part 3: The Wings ©Sebastian Hansen... - Page 34 ©Sebastian Hansen...
- Page 35 Step 62: Sand this rib carefully. ©Sebastian Hansen...
- Page 36 ©Sebastian Hansen...
- Page 37 Step 66: Do not bond the wings and fuselage using glue. ©Sebastian Hansen...
- Page 38 Part 4: The Machine Gun ©Sebastian Hansen...
- Page 39 ©Sebastian Hansen...
- Page 40 Part 5: Electronics Holder Step 71: Two pieces have been overlapped. ©Sebastian Hansen...
- Page 41 ©Sebastian Hansen...
- Page 42 ©Sebastian Hansen...
- Page 43 Step 78: Botom view. ©Sebastian Hansen...
-
Page 44: Part 6: Wire Holder
Part 6: Wire Holder Step 79: 16 pcs Wire holder. Step 80: The way to use the wire holder. ©Sebastian Hansen... - Page 45 Thank you! ©Sebastian Hansen...
Need help?
Do you have a question about the Fokker E.III Slow Flyer and is the answer not in the manual?
Questions and answers