Welcome to Electrolux! Thank you for choosing our appliance. Get usage advice, brochures, trouble shooter, service and repair information: www.electrolux.com/support Subject to change without notice. CONTENTS 1. SAFETY INFORMATION................2 2. SAFETY INSTRUCTIONS................4 3. INSTALLATION....................6 4. PRODUCT DESCRIPTION................7 5.
• Children between 3 and 8 years of age and persons with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. • Children of less than 3 years of age should be kept away from the appliance unless continuously supervised.
• Do not use high pressure water sprays and/or steam to clean the appliance. • If the appliance has ventilation openings in the base, they must not be covered e.g. by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets.
• Please note that self-repair or non- professional repair can have safety consequences and might void the guarantee. • The following spare parts are available for at least 7 years after the model has been discontinued: motor, circulation and drain pump, heaters and heating elements, including heat pumps, piping and related equipment including hoses, valves, filters...
Authorized Service Centre to replace it with appliance. the new one. 3.1 Building in www.youtube.com/electrolux www.youtube.com/aeg How to install your AEG/Electrolux 60 cm Sliding Door Dishwasher min. 560 1240 3.2 Safety caps If the furniture panel is not installed, open the appliance door carefully to avoid the risk of injury.
4. PRODUCT DESCRIPTION 4.2 Beam-on-Floor Ceiling spray arm Upper spray arm The Beam-on-Floor is a light that is displayed Lower spray arm on the floor below the appliance door. Filters • A red light comes on when a programme starts. It remains on for the duration of the Rating plate programme.
5. CONTROL PANEL On/Off button / Reset button A. ECOMETER B. Indicators Delay start button / Remote start button C. Time indicator Display 5.2 ECOMETER MY TIME program selection bar Option buttons (EXTRAS) AUTO Sense program button 5.1 Display The ECOMETER indicates how the programme selection impacts energy and water consumption.
6. PROGRAMME SELECTION 6.1 MY TIME The appliance senses the degree of soil and the amount of dishes in the baskets. It adjusts MY TIME selection bar allows to select a the temperature and quantity of water as well suitable dishwashing cycle based on as the wash duration.
Page 10
6.5 Programmes overview Programme Dishwasher Degree of Programme phases EXTRAS load soil Quick Crockery, cutlery Fresh • Dishwashing 50 °C • ExtraPower • Intermediate rinse • GlassCare • Final rinse 45 °C • ExtraHygiene • AirDry Not applicable • Prewash Pre-rinse Crockery, cutlery Fresh, lightly •...
Consumption values Water (l) Energy (kWh) Duration (min) Programme 1)2) Quick 11.0 0.620 Pre-rinse 0.010 11.8 0.970 1h 30min 11.9 1.110 2h 40min 11.9 1.210 0.644 AUTO Sense 12.1 1.220 Machine Care 10.6 0.710 The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of dishes and the degree of soil can change the values.
The order of the basic settings presented in How to change a setting the table is also the order of the settings on the ECOMETER: Make sure the appliance is in setting mode. 1. Use Previous or Next to select the bar of the ECOMETER dedicated to the desired setting.
Each performed softener rinse (possible more than one in the same cycle) may prolong the programme duration by another 5 minutes when it occurs at any point at the beginning or in the middle of a programme. All the consumption values mentioned in this section are determined in line with the currently applicable standard in laboratory conditions with water hardness...
8. WIRELESS CONNECTION You can connect your dishwasher to the The appliance returns to the programme home wireless network and then link it to your selection. Refer to "Daily use" chapter to mobile devices in the app. This functionality activate the remote start. allows you to remotely control and monitor your dishwasher.
Connect the dishwasher to the network and Refer to the instructions provided earlier in to the app to enter new network credentials. this chapter. 9. BEFORE FIRST USE 1. Adjust the level of the water softener 4. Carefully shake the funnel by its handle to according to the hardness of the water get the last granules inside.
4. Close the lid. Make sure that the lid locks CAUTION! into position. Only use rinse aid designed specifically for dishwashers. Fill the rinse aid dispenser when the 1. Open the lid (C). indicator (A) is clear. 2. Fill the dispenser (B) until the rinse aid reaches the marking ''MAX''.
• ECOMETER indicates the updated level of energy and water consumption. Opening the door deactivates the remote start. Refer to the information provided further in this chapter. By default, options must be activated every time before you start a programme. How to deactivate the remote start Press until the display shows 0h.
During the countdown, you cannot change If you open the door during the delay start the programme selection. You can change countdown, the countdown is paused. The the delay time in the app. display shows the current countdown status. After closing the door, the countdown When the countdown is complete, the resumes.
• Load the dishwasher to its full capacity to that you use tablets with long save water and energy. For best cleaning programmes. results, arrange items in the baskets as • Always use the correct quantity of instructed in the user manual and do not detergent.
• The correct quantity of detergent is used. • Put cutlery and small items in the cutlery drawer. 11.5 Loading the baskets • Move the upper basket upwards to accommodate large items in the lower • Always use the whole space of the basket.
• Do not use abrasive products, abrasive cleaning pads, sharp tools, strong chemicals, scourer or solvents. • Wipe clean the door, including the rubber gasket, once a week. • To maintain the performance of your appliance, use a cleaning product designed specifically for dishwashers at least once every two months.
CAUTION! An incorrect position of the filters can cause bad washing results and damage to the appliance. 12.6 Cleaning the lower spray arm We recommend to clean the lower spray arm regularly to prevent soil from clogging the holes. Clogged holes can cause unsatisfactory washing results.
4. To install the spray arm back, press the spray arm upwards and simultaneously turn it counterclockwise until it locks into place. 12.7 Cleaning the upper spray arm We recommend to clean the upper spray arm regularly to prevent soil from clogging the holes.
2. Move the upper basket to the lowest level 5. To install the spray arm (C) back, insert to reach the spray arm more easily. the mounting element (B) in the spray 3. To detach the spray arm (C) from the arm and fix it in the delivery tube (A) by delivery tube (A), turn the mounting turning it clockwise.
Page 26
Problem and alarm code Possible cause and solution The appliance does not fill with wa‐ • Make sure that the water tap is open. ter. • Make sure that the pressure of the water supply is not too low. For this The display shows i10 or i11.
Page 27
Problem and alarm code Possible cause and solution Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). • The appliance door is not centred on the tub. Adjust the rear foot (if ap‐ plicable).
Page 28
The display shows the PNC of your The appliance returns to the programme appliance. selection. 2. To exit the PNC presentation, press and hold simultaneously about 3 seconds. 13.2 The dishwashing and drying results are not satisfactory Problem Possible cause and solution Poor washing results.
Page 29
Problem Possible cause and solution There are residues of detergent in the • The detergent tablet was stuck in the dispenser and was not washed dispenser at the end of the pro‐ away by water. gramme. • Water cannot wash away the detergent from the dispenser. Make sure that the spray arms are not blocked or clogged.
13.3 Problems with wireless connection Problem Possible cause and solution Activating wireless connection is not • Wrong wireless network ID or password. Cancel the setup and start successful. it again to enter the correct credentials. Refer to "Wireless connec‐ tion" chapter. •...
14.1 Link to the EU EPREL database database using the link https:// eprel.ec.europa.eu and the model name and The QR code on the energy label supplied product number that you can find on the with the appliance provides a web link to the rating plate of the appliance.
Page 32
The software in this product contains components that are based on free and open source software. Electrolux gratefully acknowledges the contributions of the open software and robotics communities to the development project. To access the source code of these free and open source software components whose license conditions require publishing, and to see their full copyright information and applicable license terms, please visit: http://electrolux.opensoftwarerepository.com (folder NIUS)
Need help?
Do you have a question about the EEG68500WK and is the answer not in the manual?
Questions and answers