Advertisement
Table of Contents
Technical Support and E-Warranty Certificate www.vevor.com/support
PLATE EXCHANGER
Model: EATB28-30/EATB28-50/EATB28-80/EATB28-100
EATB12-30/EATB12-40/EATB12-60
We continue to be committed to provide you tools with competitive price.
"Save Half", "Half Price" or any other similar expressions used by us only represents an
estimate of savings you might benefit from buying certain tools with us compared to the major
top brands and does not necessarily mean to cover all categories of tools offered by us. You
are kindly reminded to verify carefully when you are placing an order with us if you are
actually saving half in comparison with the top major brands.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VEVOR EATB28-30
Summary of Contents for VEVOR EATB28-30
- Page 1 Technical Support and E-Warranty Certificate www.vevor.com/support PLATE EXCHANGER Model: EATB28-30/EATB28-50/EATB28-80/EATB28-100 EATB12-30/EATB12-40/EATB12-60 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
- Page 3 This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
-
Page 4: Parameter List
Parameter List Side Maximum Dimension Panel Connector Volumen Working Model (mm) Quantity (Q1Q2Q3 Weight (Q1-Q2/ Pressure (L1*A1*H) (pcs) (kg) Q3-Q4) (Mpa) EATB 301*126*8 4*1-1/4"N 0.84L/0.7 5.85 28-30 EATB 301*126*1 4*1-1/4"N 1.4L/1.28 8.52 28-50 EATB 301*126*2 4*1-1/4"N 2.24L/2.1 12.51 28-80 EATB 301*126*2 4*1-1/4"N 2.8L/2.68... -
Page 5: Part List
EATB 190*76*15 0.48L/0.4 4*1/2"G 12-60 Part List Model Picture EATB28-30/50/80/100 EATB12-30/40/60 Plate Exchanger Installing Support Security & Warnings 1.This product should be used for welding spigots when using refrigerant to avoid refrigerant leakage. 2.If undissolved solids like sand, weeds, leaves, and other fibers are in the water, the channels are easily blocked;... -
Page 6: Operation
BPHE and the piece; you need to use a screw cap and airproof circle to airproof. Use the ergometer to refer to the data in the table to do the screw thread link. Model Torque EATB12-30/40/60 《170 Nm EATB28-30/50/80/100 《400 Nm - 4 -... - Page 7 2. Copper brazing link Clean the weld surface and brush on the flux, using 40-50 silver-based rods for welding; the maximum temperature does not exceed 650 ℃ （ 1202F ） ; cooling water into the water-side and in the vicinity of the welding department to impose an appropriate cooling...
- Page 8 If the pipeline has vibration, longer pipe and higher thermal expansion, which will affect brazed plate heat exchanger. You'd better consider adopting the following devices: install rubber pad between brazed plate heat exchanger and bracket; compressor with shock absorber, and use corrugated pipe or other damping devices when straight pipe is longer.
- Page 9 5. Woring Schematic Diagram ⇋ ⇋ Please connection as below(Q1 Q2, Q3 Q4): Note: When the PHE use to the evaporator, the refrigerant must Q2→Q1 or Q3→Q4. When the PHE use to the condenser, the refrigerant must Q1→Q2 or Q4→Q3. - 7 -...
- Page 10 If you do not take over as shown in the figure above, there will be two media mixed together or no media outflow. 6. Exchanger Selection Note: The data in ( ) is the default value, you may fill in this form with appropriate data.
- Page 11 - 9 -...
- Page 13 Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the EATB28-30 and is the answer not in the manual?
Questions and answers