Advertisement

SPECIFICATIONS
Part # 110816
Set Up Size: (L 113" x W 86" x H 83")
Packed Size: (L 86" x W 45" x H 28")
W e i g h t: 195 lbs.
Instructions Document No: 105843
Please contact customer service directly at the E-mail or phone number listed below for any
quality issues. ONCE USED THIS PRODUCT CANNOT BE RETURNED TO STORE.
** Warranty cannot be honored without an original, dated receipt **
** REGISTER YOUR PURCHASE ONLINE AT CLAMOUTDOORS.COM **
IMPORTANT-PLEASE READ:
This product is warranted to the original retail purchaser (from an authorized dealer) and is non-transferable.
Clam Outdoors has a three year manufacturer's defect warranty from the date of original purchase. Warranty
does not cover cracked or worn bases (if runner kits have not been installed as recommended), cracked
windows, tent tears or cuts, or broken or bent hoops due to high wind weather conditions or unattended use.
Defective parts will be replaced or repaired (at the manufacturer's option) if found to be defective within three
year from the date of original purchase. Warranty will be void if product has been subject to neglect, misuse,
improper installation, misapplication, alteration, accident including but not limited to improper maintenance, or use
of unauthorized parts or attachments. Please read the entire owner's manual to ensure proper installation, use,
storage and care of your Clam Shelter.
To submit a warranty claim request, please use one of the following methods:

Customer Service Hrs: 9am to 4pm, Monday – Friday Central Standard Time

Clam Outdoors, Inc.
Attn: Customer Service – Warranty Department
12135 Brockton Lane
Rogers, MN 55369

Phone: 763-231-4120

Fax: 763-231-4121

Email:
customerservice@clamcorp.com

Website:
Clamoutdoors.com
In your request, please include your full name, address, phone number, a copy of your receipt, a brief description
of the problem, and pictures to clearly show the area(s) of concern. Our Warranty Department will review your
request, and a Clam representative will contact you regarding your claim status. All returns must be shipped to us
postage pre-prepaid.
It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is not
liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of
use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to use,
or the repair or replacement of Clam products. Clam reserves the right to make alterations or modifications in
its products at any time, which in its opinion, may improve the performance and efficiency of the product. Clam
shall not be obligated to make such alterations or modifications to products already in service.
STEP 6
WARRANTY INFORMATION
LIMITATION OF LIABILITY
MODELS 10816

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the THERMAL X300 and is the answer not in the manual?

Questions and answers

Summary of Contents for Clam THERMAL X300

  • Page 1 It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is not liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to use, or the repair or replacement of Clam products.
  • Page 2: Parts List

    PARTS LIST PART NO. DESCRIPTION QTY. 104997 BASE, X300 STEP 6 104999 TUBE, HOOP, X300 105089 TUBE, HALF HOOP, X300 109560 LIGHT STICK LARGE 104998 TENT, X300 PRO THERMAL 105449 EXTRUSION, V-CHANNEL 104916 KIT, SPRDR POLES, X200 105090 TUBE, SEAT RAIL, X300 102759 ASSY, DELUXE SEAT 103638...
  • Page 3 HARDWARE FASTENERS REFERENCE STEP 6...
  • Page 4: Required Tools

    REQUIRED TOOLS STEP 6 #2 AND #3 PHILLIPS HAND SCREW 3/8 AND 7/16 COMBINATION WRENCH OR SOCKETS #6 PHILLIPS SCREW BIT 3/16 AND 3/8 DRILL POWER DRILL...
  • Page 5 *USING A DROP OF OIL ON ALL NUTS WILL EASE THE ASSEMBLY PROCESS. STEP 6 *IT IS BEST TO USE THE AID OF ANOTHER PERSON DURING ASSEMBLY. STEP 1 RUNNER KIT INSTALLATION 1. Position the strips on the base. Using a 3/16” Drill bit, drill a hole through the base using existing holes in the runner strip starting at the curved end of the base.
  • Page 6 STEP 2 STEP 6 1. INSERT CAP TUBES (101430) INTO EACH SIDE OF RAIL SUPPORT. 2. INSTALL (104901) AND (102083) TO RAIL SUPPORT. (SEE DIAGRAM) 3. INSTALL RAIL SUPPORT TO BASE USING THE PRE DRILLED HOLES. 4. SECURELY TIGHTEN ALL FASTENERS. 105090 STEP 3 1.
  • Page 7 STEP 4 STEP 6 CHOOSE WHICH LOCATION YOU PREFER TO HAVE BATTERY LOCATED. LIGHT POLE WIRE WILL NEED TO BE ABLE TO REACH BATTERY. 1. INSTALL BATTERY BRACKET, ASSEMBLY (108829) AS SHOWN USING 3/8” DRILL BIT OR REFER TO INSTALLATION MANUAL THAT IS INCLUDED WITH KIT STEP 5 1.
  • Page 8 STEP 6 STEP 6 1. INSTALL POLES TO BOTH SIDES AS SHOWN. POLES SHOULD MOVE EASILY, DO NOT OVERTIGHTEN POLE SLOTS MUST FACE INWARD TOWARD BASE ASSEMBLY AT THIS POINT...
  • Page 9 STEP 7 STEP 6 DO NOT CUT ANY OF YOUR POLES! 1. ASSEMBLE LIGHT STICK (109560) TO HALF POLES (104897) AS SHOWN 105089 2. ASSEMBLE REMAINING POLES AS SHOWN 104999...
  • Page 10 STEP 6 STEP 8 1. INSTALL HOOP POLES OVER POLES AND SUPPORTING SPREADER POLES AS SHOWN 2. INSERT(101249) ROPE ENDS THRU HOLES IN FRONT OF BASE AND KNOT EACH END. LIGHT STICK (109560) WIRE TO BE POSITIONED TO SAME SIDE AS BATTERY HOLDER! DO NOT INSTALL FRONT HOOP POLE UNTIL STEP 14.
  • Page 11 STEP 9 STEP 6 ROTATE THE SWIVEL 45 DEGREES TO AID IN THE INSTALLATON PROCESS AS SHOWN. ASSEMBLY AS SHOWN AND SECURELY TIGHTEN. SAME BLOCK STYLES MUST BE ALIGNED TO EACH OTHER 105478 STEP 10 1. INSTALL THE ASSEMBLY FROM STEP 7 TO SEAT AS SHOWN AND SECURELY TIGHTEN...
  • Page 12 STEP 11 STEP 6 1. INSTALL SEAT COVERS OVER SEAT AS SHOWN USING VELCRO STRAPS TO FASTEN IN PLACE STEP 12 1. ASSEMBLE THIS END OF THE SEAT ASSEMBLY AS SHOWN AND SECURELY TIGHTEN.. 101466 HAMMOCK (THIS FABRIC ACCESSORY HOLDER IS PACKAGED IN WITH THE TENT) ASSEMBLED VIEW...
  • Page 13 STEP 13 STEP 6 1. SLIDE THE ASSEMBLY FROM PREVIOUS STEP THRU SEAT BLOCKS AS SHOWN. MUST LIFT HAMMOCK OVER BLOCKS AND SECURE TO TUBE AS SHOWN IN NEXT STEP. STEP 7 STEP 14 1. ASSEMBLE THIS END OF THE SEAT ASSEMBLY AS SHOWN AND SECURELY TIGHTEN ASSEMBLED VIEW COMPLETED SEAT ASSEMBLY...
  • Page 14 STEP 15 STEP 6 1. SLIDE FRONT OF SEAT ASSEMBLY INTO OUTER FLANGE OF BASE AND DROP BACK SIDE INTO PLACE. THEN SNAP (102512) LATCH INTO POSITION TO SECURE SEAT ASSEMBLY AS SHOWN STEP 16 1. DRAPE THE TENT, OVER THE HOOP POLES. ATTACH THE TENT TO THE POLES ON THE INSIDE WITH THE VELCRO STRAPS.
  • Page 15 STEP 17 HEAT THE MOLDING (102814) WITH A BLOW DRYER, HEAT GUN OR SOAK IN HOT WATER MAKING IT PLIABLE. DETAIL-B THE FRONT HOOP POLE SHOULD TOUCH THE FLOOR WHEN THE TENT IS SET CORRECTLY DETAIL-A To “set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the front fishing area of the tent lifting accordingly as you pull.
  • Page 16 STEP 18 THERE IS AN APRON ATTACHED TO THE X300 TENT TO HELP REDUCE WIND INTRUSION. 1. .SIMPLY SNAP THE CLIPS AND USE THE VELCRO STRIPS TO HOLD EACH SIDE TOGETHER. 2. USE GROMMET HOLES TO HANG APRON ONTO THE TWO BOLTS FOR SUPPORT...
  • Page 17: Tips For Use

    (NOTE: Pulling behind an ATV or snowmobile may result in premature wear of the base). ▪ In windy conditions it is advised to secure your shelter to the ice using Clam’s Ice Anchor Kit (PN 108064) and Ice Anchor Installation Tool (PN 108348).
  • Page 18: Frequently Asked Questions

    Q: What will help keep mice or rodents from eating the tent of my Clam or Fish Trap? A: We recommend that you keep your tent in a sealed plastic tote with laundry dryer sheets or moth balls. If the shelter is stored in a barn or shed take the tent off the house and store it in a rodent-free environment such as in your home.
  • Page 19 We are only set up to ship warranty or replacement parts required to MAINTAIN a Clam shelter (tents, poles, parts, patch kits, etc.). No accessories – see a local dealer or an online dealer of Clam products. If the replacement parts are not under warranty you will be charged for the product plus actual shipping charges.

This manual is also suitable for:

10816

Table of Contents