Advertisement

SPECIFICATIONS
Part Numbers: 114464
Set Up Size: (L 113" x W 74" x H 82")
Packed Size: (L 74" x W 42-1/2" x H 22-1/4")
W e i g h t: 130 lbs.
Instructions Document No: 106172
Please contact customer service directly at the E-mail or phone number listed below for any
quality issues. ONCE USED THIS PRODUCT CANNOT BE RETURNED TO STORE.
** Warranty cannot be honored without an original, dated receipt **
** REGISTER YOUR PURCHASE ONLINE AT CLAMOUTDOORS.COM **
IMPORTANT-PLEASE READ:
This product is warranted to the original retail purchaser (from an authorized dealer) and is non-transferable.
Clam Outdoors has a three year manufacturer's defect warranty from the date of original purchase. Warranty
does not cover cracked or worn bases (if runner kits have not been installed as recommended), cracked windows,
tent tears or cuts, or broken or bent hoops due to high wind weather conditions or unattended use. Defective parts
will be replaced or repaired (at the manufacturer's option) if found to be defective within three year from the date
of original purchase. Warranty will be void if product has been subject to neglect, misuse, improper installation,
misapplication, alteration, accident including but not limited to improper maintenance, or use of unauthorized parts or
attachments. Please read the entire owner's manual to ensure proper installation, use, storage and care of your Clam
Shelter.
To submit a warranty claim request, please use one of the following methods:
Customer Service Hrs: 9am to 4pm, Monday – Friday Central Standard Time
Clam Outdoors, Inc.
Attn: Customer Service – Warranty Department
12135 Brockton Lane
Rogers, MN 55369
Phone: 763-231-4120
Fax: 763-231-4121
Email:
customerservice@clamcorp.com
Website:
Clamoutdoors.com
In your request, please include your full name, address, phone number, a copy of your receipt, a brief description of
the problem, and pictures to clearly show the area(s) of concern. Our Warranty Department will review your request,
and a Clam representative will contact you regarding your claim status. All returns must be shipped to us postage
pre-prepaid.
It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of warranty,
negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is not liable for any
injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of use, income, profit,
or damage to material arising in connection with the sale, installation, use of, inability to use, or the repair or
replacement of Clam products. Clam reserves the right to make alterations or modifications in its products at
any time, which in its opinion, may improve the performance and efficiency of the product. Clam shall not be
obligated to make such alterations or modifications to products already in service.
STEP 6
WARRANTY INFORMATION
LIMITATION OF LIABILITY
MODELS 14464

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the X200 THERMAL 14464 and is the answer not in the manual?

Questions and answers

Summary of Contents for Clam X200 THERMAL 14464

  • Page 1 It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is not liable for any...
  • Page 2: Parts List

    STEP 6 PARTS LIST includes extra washers, nuts, screws and bolts. QTY. PART NO. DESCRIPTION 104898 BASE, X200 104892 TUBE, HOOP, X200/X400 106163 TENT, X200 THERMAL 104916 KIT, SPRDR POLES, X200 (INCLUDES THE FOLLOWING) 104913 ASSY, SPREADER, ROOF, .88 X 40.) 101840 ASSY, XTR REAR SPRDR 104915...
  • Page 3 STEP 6 HARDWARE FASTENERS REFERENCE...
  • Page 4: Required Tools

    STEP 6 REQUIRED TOOLS #2 AND #3 PHILLIPS HAND SCREW 3/8 AND 7/16 COMBINATION WRENCH OR SOCKETS #2 PHILLIPS SCREW BIT 3/16 AND 3/8 DRILL BIT POWER DRILL...
  • Page 5 STEP 6 *USING A DROP OF OIL ON ALL NUTS WILL EASE THE ASSEMBLY PROCESS. *IT IS BEST TO USE THE AID OF ANOTHER PERSON DURING ASSEMBLY. STEP 1 INSTALL ANY RUNNER KIT OPTIONS BEFORE ASSEMBLING SHELTER. REFER TO RUNNER KIT INSTRUCTIONS 1.
  • Page 6 STEP 6 STEP 3 1. INSTALL POLES TO BOTH SIDES AS SHOWN. POLES SHOULD MOVE EASILY, DO NOT OVERTIGHTEN POLE SLOTS MUST FACE INWARD TOWARD BASE ASSEMBLY AT THIS POINT...
  • Page 7 STEP 4 STEP 6 1. SLIDE COLLAR (103605) ONTO HOOP POLE (104892) UNTIL SNAPS IN PLACE 104892 104892 STEP 5 1. INSTALL HOOP POLES OVER POLES AND SUPPORTING SPREADER POLES AS SHOWN 2. INSERT(101249) ROPE ENDS THRU HOLES IN FRONT OF BASE AND KNOT EACH END. DO NOT INSTALL FRONT HOOP POLE AT THIS TIME...
  • Page 8 STEP 6 STEP 6 ROTATE THE SWIVEL 45 DEGREES TO AID IN THE INSTALLATON PROCESS AS SHOWN. 1. ASSEMBLY AS SHOWN AND SECURELY TIGHTEN. SAME BLOCK STYLES MUST BE ALIGNED TO EACH OTHER 105478 STEP 7 1. INSTALL THE ASSEMBLY FROM STEP 7 TO SEAT AS SHOWN AND SECURELY TIGHTEN...
  • Page 9 STEP 8 STEP 6 106166 1. INSTALL SEAT COVERS OVER SEAT AS SHOWN USING VELCRO STRAPS TO FASTEN IN PLACE 106167 STEP 9 1. ASSEMBLE THIS END OF THE SEAT ASSEMBLY AS SHOWN AND SECURELY TIGHTEN.. 101466 HAMMOCK (THIS FABRIC ACCESSORY HOLDER IS PACKAGED IN WITH THE TENT) ASSEMBLED VIEW...
  • Page 10 STEP 10 STEP 6 1. SLIDE THE ASSEMBLY FROM PREVIOUS STEP THRU SEAT BLOCKS AS SHOWN. MUST LIFT HAMMOCK OVER BLOCKS AND SECURE TO TUBE AS SHOWN IN NEXT STEP. STEP 7 STEP 11 1. ASSEMBLE THIS END OF THE SEAT ASSEMBLY AS SHOWN AND SECURELY TIGHTEN 103788 ASSEMBLED VIEW COMPLETED SEAT ASSEMBLY...
  • Page 11 STEP 12 STEP 6 1. SLIDE FRONT OF SEAT ASSEMBLY INTO OUTER FLANGE OF BASE AND DROP BACK SIDE INTO PLACE. THEN SNAP (102512) LATCH INTO POSITION TO SECURE SEAT ASSEMBLY AS SHOWN STEP 13 1. DRAPE THE TENT, OVER THE HOOP POLES. ATTACH THE TENT TO THE POLES ON THE INSIDE WITH THE VELCRO STRAPS.
  • Page 12 STEP 14 HEAT THE MOLDING (102814) WITH A BLOW DRYER, HEAT GUN OR SOAK IN HOT WATER MAKING IT PLIABLE. DETAIL-B 106163 THE FRONT HOOP POLE SHOULD TOUCH THE FLOOR WHEN THE TENT IS SET CORRECTLY DETAIL-A To “set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the front fishing area of the tent lifting accordingly as you pull.
  • Page 13: Tips For Use

    (NOTE: Pulling behind an ATV or snowmobile may result in premature wear of the base). ▪ In windy conditions it is advised to secure your shelter to the ice using Clam’s Ice Anchor Kit (PN 108064) and Ice Anchor Installation Tool (PN 108348).
  • Page 14: Frequently Asked Questions

    Q: What will help keep mice or rodents from eating the tent of my Clam or Fish Trap? A: We recommend that you keep your tent in a sealed plastic tote with laundry dryer sheets or moth balls. If the shelter is stored in a barn or shed take the tent off the house and store it in a rodent-free environment such as in your home.
  • Page 15 We are only set up to ship warranty or replacement parts required to MAINTAIN a Clam shelter (tents, poles, parts, patch kits, etc.). No accessories – see a local dealer or an online dealer of Clam products. If the replacement parts are not under warranty you will be charged for the product plus actual shipping charges.

Table of Contents