Hide thumbs Also See for 116609:

Advertisement

SPECIFICATIONS
Part Number: 116609
Set Up Size:109L" x 42"W x 80"H
Packed Size:56"L x 42"W x 27"H
W e i g h t: 82 lbs.
Fishable Area: 14 sq.ft
Instructions: 106984
Please contact customer service directly at the E-mail or phone number listed below for any
quality issues. ONCE USED THIS PRODUCT CANNOT BE RETURNED TO STORE.
** Warranty cannot be honored without an original, dated receipt **
IMPORTANT-PLEASE READ:
This product is warranted to the original retail purchaser (from an authorized dealer) and is non-transferable.
Clam Outdoors has a three-year manufacturer's defect warranty from the date of original purchase. Warranty
does not cover cracked or worn bases (if runner kits have not been installed as recommended), cracked
windows, tent tears or cuts, or broken or bent hoops due to high wind weather conditions or unattended use.
Defective parts will be replaced or repaired (at the manufacturer's option) if found to be defective within three
years from the date of original purchase. Warranty will be void if product has been subject to neglect, misuse,
improper installation, misapplication, alteration, accident including but not limited to improper maintenance, or
use of unauthorized parts or attachments. Please read the entire owner's manual to ensure proper installation,
use, storage and care of your Clam Shelter.
To submit a warranty claim request, please use one of the following methods:
https://clamoutdoors.com/pages/warranty-form
▪ Email:
customerservice@clamcorp.com
In your request, please include your full name, address, phone number, a copy of your receipt, a brief description
of the problem, and pictures to clearly show the area(s) of concern. Our Warranty Department will review your
request, and a Clam representative will contact you regarding your claim status. All returns must be shipped to
us postage pre-prepaid.
It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of
warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is
not liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss
of use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to
use, or the repair or replacement of Clam products. Clam reserves the right to make alterations or
modifications in its products at any time, which in its opinion, may improve the performance and efficiency of
the product. Clam shall not be obligated to make such alterations or modifications to products already in service
Clam contact information
Customer Service Hrs: 9am to 4pm, Monday – Friday Central Standard Time
Clam Outdoors
Attn: Customer Service
12135 Brockton Lane
Rogers, MN 55369
Phone: 763-231-4120
FISH TRAP BUILD VIDEO
CLAMOUTDOORS.COM
WARRANTY INFORMATION
** REGISTER YOUR PURCHASE ONLINE AT CLAMOUTDOORS.COM **
LIMITATION OF LIABILITY
MODEL 16609

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 116609 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Clam 116609

  • Page 1 It is expressly understood that Clam Outdoors Inc., liability for its products, whether due to breach of warranty, negligence, strict liability, or otherwise, is limited to the repair of the product as stated above. Clam is not liable for any injury, loss, damage, or expense, whether direct or consequential, including but not limited to loss of use, income, profit, or damage to material arising in connection with the sale, installation, use of, inability to use, or the repair or replacement of Clam products.
  • Page 2: Parts List

    PARTS LIST QTY. PART NO. DESCRIPTION 105039 BASE, X100 106919 HOOP POLE, X100 XT 106920 EXTENSION HOOP POLE, X100 XT (GREEN ZIP TIE) 106797 TENT, X100 THERMAL XT 105449 U-CHANNEL 101840 REAR ADJUSTABLE SPREADER POLE 106509 SEAT RAIL 102759 DELUXE SEAT 107352 SEAT COVER, BOTTOM 107351...
  • Page 3 HARDWARE FASTENERS REFERENCE...
  • Page 4: Step 1 - Seat Assembly

    STEP 1 – SEAT ASSEMBLY Parts Needed for Step 1 Part Number Description Quantity 101652 SEAT TUBE 101429 SEAT TUBE PLUG 101048 BLOCK, SLIDE (CIRCLE) 104674 BLOCK, SLIDE (OVAL) 101146 EXTRUSION CHANNEL 105478 SWIVEL, SEAT 102759 DELUXE SEAT 101420 FRONT RETAINER BRACKET 102430 REAR RETAINER...
  • Page 5 D. Rotate Seat Swivel #105478 45 degrees so its star shaped and all slotted holes are accessible. E. Use #106286 bolts and #106284 nuts to secure Extrusion Channels to Swivel. F. Attach swivel assembly to bottom of Deluxe Seat #102759 with #101470 screws and tighten. G.
  • Page 6 H. Installing the Front Retainer #101420 and Rear Retainer #102430 brackets – Line up holes of Retainer Brackets to Seat Rail Tubes and insert #106456 bolts. NOTE: REAR RETAINER BRACKET CONTAINS THE SEAT LATCH CLIP. I. Locate Hammock #101466, which is a fabric accessory included inside the tent bag. J.
  • Page 7 STEP 2 – EXTENSION HOOP POLE DO NOT CUT ANY OF YOUR POLES NOTE: The Extension Hoop Pole #106920 is identified with a green zip tie. This pole is also shorter in length than the other hoop poles included with the shelter. Parts Needed for Step 2 Part Number Description...
  • Page 8 C. Attach Extension Support Poles #106922 with the notch of the pole facing inward. Use hardware provided with the Extension Clamps to secure. NOTE: Do not overtighten as this pole needs to move freely. Hardware included with Extension Clamp D. Clip green zip tie and install RPSX Collar #103605 onto Extension Hoop Pole #106920 (see figures below and on next page).
  • Page 9 TIP: Twist the lever on the RPSX Collars 90 degrees to allow for easier installation onto Hoop Pole. E. Install Extension Hoop Pole onto Extension Support Poles (shown below). Extension Hoop Pole #106920 Hoop Pole #106919...
  • Page 10 STEP 3 – HOOP POLE ASSEMBLY Parts Needed for Step 3 Part Number Description Quantity 106919 HOOP POLE EXTENSION HOOP POLE ASSEMBLY (from Step 2) 106508 CAP TUBE SPACER 106506 SWIVEL PLATE 106507 PLASTIC HOOP SPACER 106331 SCREW, 1/4-20 X 2.50 106510 SCREW, 1/4-20 x 1.812 101082...
  • Page 11 B. Lay one Hoop Pole down and place the Extension Hoop Pole Assembly from Step 3 on top. Using the Plastic Hoop Spacers #106507 and hardware shown in the figure below, install poles onto the Swivel Plate #106506. C. Repeat process for other side. DO NOT OVERTIGHTEN - POLES MUST MOVE FREELY ONCE INSTALLED Leave this bolt open...
  • Page 12: Step 4 - Seat Rail

    STEP 4 – SEAT RAIL Parts Needed for Step 4 Part Number Description Quantity 106509 SEAT RAIL 101430 CAP TUBE 102083 RAIL SUPPORT BRACKET 106456 SCREW, 1/ 4-20 X 1.75 106284 NUT, 1/4-20, NYLOCK 106286 SCREW, 1/4-20 X 0.75 A. Line up Rail Support Bracket #102083 with predrilled holes on wall of sled. B.
  • Page 13: Step 5 - Mounting Brackets

    STEP 5 – MOUNTING BRACKETS Parts Needed for Step 5 Part Number Description Quantity 106505 MOUNTING BRACKET 106286 SCREW, 1/4-20 X 0.75 106284 NUT, 1/4-20, NYLOCK A. Place Mounting Bracket #106505 with the ‘L’ facing outwards as shown below. B. Insert #106286 bolts and secure to base using #106284 nuts.
  • Page 14 STEP 6 – INSTALLING POLE ASSEMBLY Parts Needed for Step 6 Part Number Description Quantity HOOP POLE ASSEMBLY (from Step 3) 103835 LARGE PLASTIC WASHER 106284 NUT, 1/4-20, NYLOCK A. Place the Large Plastic Washer #103835 onto the longer Hoop Pole Assembly bolt (from Step 3).
  • Page 15 STEP 8 – TENT INSTALLATION **FOR AN ALTERNATIVE OPTION FOR INSTALLING THE TENT, PLEASE REFER TO THE SETUP VIDEO INSTRUCTIONS FOUND THROUGH THE QR CODE ON PAGE 1 OF THIS MANUAL** Parts Needed for Step 8 Part Number Description Quantity 106797 TENT, X100 THERMAL 106919...
  • Page 16 Soaking the U-Channel #102814 in hot water will make it much more pliable and easier to wrap around shelter DETAIL-B 8” Approx. BOTH SIDES DETAIL-A THE FRONT HOOP POLE SHOULD REMOVE REAR TOUCH THE FLOOR WHEN THE TENT IS SPREADER POLE SET CORRECTLY WITH SOME SLACK IN WHILE INSTALLING U- THE FRONT PART OF THE TENT...
  • Page 17: Tips For Use

    NOTE: Pulling behind an ATV or snowmobile may result in premature wear of the base. ▪ In windy conditions it is advised to secure your shelter to the ice using Clam’s Ice Anchor Kit (PN 108064) and Ice Anchor Installation Tool (PN 108348).
  • Page 18: Safety Instructions

    SAFETY INSTRUCTIONS Please fully understand and follow all safety instructions as outlined. Failure to do so could result in severe injury or death. ▪ DO NOT USE OPEN FLAME HEATERS IN YOUR ICE SHELTER. INJURY OR DEATH MAY RESULT FROM FIRE IF TENT FABRIC IS EXPOSED TO OPEN FLAME. THE TENT IS NOT FIREPROOF, BUT THE FABRIC IS TREATED WITH A FIRE RETARDANT THAT MEETS CPAI-84 SPECIFICATIONS.
  • Page 19: Frequently Ask Questions

    FREQUENTLY ASK QUESTIONS Fish Trap FAQ’s Q: Should I install a runner kit/hyfax to the base of my shelter? A: The warranty on our shelters does not cover cracked or worn bases if a runner kit has not been installed. Additionally, bases will wear much quicker without a runner kit installed. Q: The zipper on my shelter freezes up and/or sticks.
  • Page 20 coating has come off, you may wish to apply a new layer of rubberized coating. A thin layer of Loctite Color Guard (black), found online or at home improvement stores, works well. Q: Would it be best to completely dry out my shelter after every time it gets used? A: It is recommended your tent be dried out completely after each use.

This manual is also suitable for:

100xt pro thermal 16609X100 series

Table of Contents