Sealey SUPERMIG275.V3 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear a
instruction welding
manual mask
Breathing welding Electromagnetic
fumes can be fields can cause
hazardous to your pacemaker
health malfunction
1. SAFETY
1.1. ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and all electrical
9
connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical products.
Electrical safety information. It is important that the following information is read and understood:
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
9
Important: Ensure that the voltage rating on the appliance suits the pow er supply to be used and that the plug is fitted with the correct fuse.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or is replaced immediately by a
8
qualified electrician.
If the cable or plug is damaged during use, switch off the electricity supply and remove from use.
Ensure that repairs are carried out by a qualified electrician.
DO NOT use with medical implants. Ensure the unit is correctly earthed via a three-pin plug.
8
Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD fitted
9
is recommended since any product which is plugged into the cable reel will be protected. The section of the cable on the cable reel is
important and should be at least 1.5mm², but to be absolutely sure that the capacity of the cable is suitable for this product and for others
that may be used in the other output sockets, we recommend the use of 2.5mm² section cable.
WARNING! Be very cautious if using a generator to power the welder. The generator must be self-regulating and stable with regard to
‰
voltage, wave form and frequency. The output must be greater than the power consumption of the welder. If any of these requirements is
not met the electronics within the welder may be affected.
NOTE: The use of an unregulated generator may be dangerous and will invalidate the warranty on the welder.
WARNING! The welder may produce voltage surges in the mains supply which can damage other sensitive equipment (e.g. computers).
‰
To prevent this happening, it is recommended that the welder is connected to a power supply that does not feed any sensitive equipment.
IMPORTANT: If using welder to full capacity, we recommend a 16amp supply. We recommend you discuss the installation of a 16amp
industrial round pin plug and socket with your electrician.
1.2. GENERAL SAFETY
▲ DANGER! Unplug the welder from the mains power supply before performing maintenance or service.
Welding power sources are not suitable for use in rain or snow.
8
The output is rated at an ambient temperature of 20°C and the welding time may be reduced at higher temperatures
8
The unit must be placed on a flat, level surface to reduce risk of toppling over.
9
WARNING! Risk of electric shock: Electric shock from welding electrode can kill. DO NOT weld in the rain or snow. Wear dry insulating
‰
gloves. DO NOT touch electrode with bare hands. DO NOT wear wet or damaged gloves. Protect yourself from electric shock by
insulating yourself from workpiece. DO NOT open the equipment enclosure.
WARNING! Risk induced by welding fumes: Breathing welding fumes can be hazardous to your health. Keep your head out of the fumes.
‰
Use equipment in an open area. Use ventilating fan to remove fumes.
WARNING! Risk induced by welding sparks: Welding sparks can cause explosion or fire. Keep flammables away from welding. DO NOT
‰
weld near flammables. Welding sparks can cause fires. Have a fire extinguisher nearby and have a watchperson ready to use it. DO NOT
weld on drums or any closed containers.
WARNING! Risk induced by the arc: Arc rays can burn eyes and injure skin. Wear hat and safety glasses. Use ear protection and button
‰
shirt collar. Use welding helmet with correct shade of filter. Wear complete body protection.
© Jack Sealey Limited
270A PROFESSIONAL GAS/GASLESS MIG
WELDER WITH BINZEL® EURO TORCH
MODEL NO'S:
Wear protective Warning!
gloves Electricity
Shock hazard
NOTE:
Diagrams of internal components are for reference only.
There may be detail differences in the components of your
welder but these will not affect its operation.
Original Language Version
SUPERMIG275.V3
Warning! Caution
Keep away required burn eyes and
from rain
Arc rays can Electric shock
from welding
injure skin electrodes can
kill
SUPERMIG275.V3
Welding sparks
can cause
explosions or
fire
Issue 1 07/05/24