1. Manuals
  2. Brands
  3. zika Manuals
  4. Welding System
  5. FM-200
  6. User manual

zika FM-200 User Manual

Inverter dc mig welding machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
User's Manual
Inverter DC MIG Welding
Machine Series
FM-200
Model:
FM-200

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FM-200 and is the answer not in the manual?

Questions and answers

Related Manuals for zika FM-200

Summary of Contents for zika FM-200

  • Page 1 User’s Manual Inverter DC MIG Welding Machine Series FM-200 Model: FM-200...

  • Page 2: Part 1: Machine Introduction

    Operation Manual FM-200 welding machines adopts the latest pulse width modulation (PWM) technology and insulated gate bipolar transistor (IGBT) power module, which can change work frequency to medium frequency so as to replace the traditional Transistor transformer with the medium frequency transformer. its characterized with portable, small size, light weight, low consumption and etc.
  • Page 3 Version Number: FM-200-20211231A1 Part 2: Introduction to the product and configuration list Picture Name Remark Please check outside of the whole machine no FM-200 scratch and break , it can power on normally. MB15 3M, MB 15 MIG welding torch, European central welding plug.
  • Page 4 Part 3: Simple test for powering on the machine FM-200 Welding machines will be subjected to strict various tests when they leave the factory to ensure that each welding machine that reaches the user is of high quality, because our machine has to go through tens of thousands of kilometers of long-distance transportation from the factory to the delivery to you.

  • Page 5: Part 4: Technical Specifications

    5. Use approved ear plugs or ear muffs if noise level is high; 6. Never wear contact lenses while welding. 5.1 STICK mode If you want to repair some broken fences or fix brackets, you like to use traditional welding rods for operation, you can use FM-200 MMA mode for welding.
  • Page 6 3 To adjust the current, Knob “STICK/LIFT TIG” only the current can be adjusted. Note: 1) The welding rod specification supported by FM-200 is below 4.0(5/32in), usually 2.5(3/32in) and 3.2(1/8in). European style generally uses E6013, American style generally uses E7018, and stainless steel generally uses ER308.

  • Page 7: Mig Mode

    MIG mode FM-200 provides two welding modes: gas shielded welding and self-shielded welding with fluxed wire. If you are working at home or in a studio, in order to ensure a better welding effect, it is recommended that you use the gas welding mode;...

  • Page 8: Install Wire Spool

    Version Number: FM-200-20211231A1 1.1.2 Self-protection mode of flux-cored welding wire（without gas） 1.1.3 SPOOL GUN mode Remarks: 1、SPOOL GUN needs to be purchased separately；2、For welding solid wire, the polarity plug is connected to the positive pole; for welding flux-cored wire, the polarity plug is connected to the negative pole.
  • Page 9 Version Number: FM-200-20211231A1 Set drive roll Face the side marked 0.030” away from the machine. Remarks: 1. There are two grooves on one wire feed wheel, one side is 0.030” (0.8mm) and the other side is 0.040” (1.0mm) to match the corresponding wire diameter.
  • Page 10 Please refer to the digital sign on the rear panel of the machine for the input voltage, the wrong voltage will damage the machine. FM-200 only has 230V voltage input, FM-200D supports 110V or 220V voltage input. 1.6 Installation of welding torch.
  • Page 11 Version Number: FM-200-20211231A1 1.9 With contact tip 1/4” from metal, depress trigger completely to initiate arc. 1.10 To replace the welding wire. Use the cutting pliers to cut off the front section of the contact tip that is more than the welding wire,...
  • Page 12 Version Number: FM-200-20211231A1 Remarks: For gas welding Solid carbon steel wires, please use copper nozzles. Remarks: For gasless welding flux-cored wires, please use porcelain nozzles. Note: 1) Please strictly follow the picture instructions to connect, otherwise it will not be possible to solder.

  • Page 13: Lift-Tig Mode

    6） If you have any questions, please contact us . 5.3 LIFT-TIG mode FM-200 for thin plates with higher welding process requirements or welding with higher process requirements, especially for stainless steel welding, you can use the LIFT TIG mode, which requires the use of pure argon.
  • Page 14 Version Number: FM-200-20211231A1 3. Adjust the current, only the current (STICK/LIFT TIG)can be adjusted. 4. WP17V Structure of welding torch Note: Standard accessories package kit not included this tig torch. Remark: 1. ceramic nozzle, 2 .tungsten collect, 3. tungsten collect body, 4 .short back cap, 5. long back cap.

  • Page 15: Part 6:Troubleshooting

    Version Number: FM-200-20211231A1 Part 6:Troubleshooting Observe all Safety Guidelines detailed throughout this manual PROBLEMS POSSIBLE (SYMPTOMS) CAUSE OUTPUT PROBLEMS “Do not Plug in machine or turn it on”. Major physical or electrical damage is evident. Contact your local Authorized Field Service Facility.
  • Page 16 Version Number: FM-200-20211231A1 Part 7: Welding parameter settings MIG machine welding parameters Shielding Material Thickness-110V Material Thickness-220V Polarity Wire Material Wire Type Settings 24 Ga. 20 Ga. 18 Ga. 16 Ga. 14 Ga. 20-30 Setting Size 24 Ga. 20 Ga.

  • Page 17: Warranty Card

    Version Number: FM-200-20211231A1 Warranty Card Warranty period from the purchase date : 1、One year warranty for welding and cutting machine. 2、3 months warranty for welding accessories. 3、The warranty does not cover faults resulting from operation careless handing or not following instructions.

Table of Contents