Download
Share
Print this page
  1. Manuals
  2. Brands
  3. zika Manuals
  4. Welding System
  5. I-PLAS 25
  6. Owner's manual

zika I-PLAS 25 Owner's Manual

Hide thumbs

Advertisement

Quick Links

ZIKA
OWNER'S MANUAL
I-PLAS 25/40

Advertisement

loading

Related Manuals for zika I-PLAS 25

Summary of Contents for zika I-PLAS 25

  • Page 1 ZIKA OWNER'S MANUAL I-PLAS 25/40...

  • Page 2: Table Of Contents

    CONTENTS 1. Contents ..............................1 2. Safety warning ............................2 3. Machine description ........................... 3 4. Technical parameters table........................4 5. Installation instruction ..........................5 6. Operation instruction ..........................7 7. Panel instruction ............................8 8. Notes or preventive measures ........................ 10 9.

  • Page 3: Safety Warning

    SAFETY WARNING On the process of welding or cutting, there will be possibility of injury, so please take protection into consideration during operation. For more details please review the Operator Safety Guide, which complies with the preventive requirements of the manufacturer. Electric shock——May lead to death ！...

  • Page 4: Machine Description

    MACHINE DESCRIPTION The welding machines are rectifiers adopting the most advanced inverter technology, which can apply in plasma cutting system of using pressing air. The development of inverter welding equipment benefits from the development of the inverter power supply theory and components.

  • Page 5: Technical Parameters Table

    TECHNICAL PARAMETERS TABLE Model I-PLAS25 I-PLAS40 Parameters Input voltage（V） AC380V15% AC380V15% Rate input current（A） 23.1 No-load voltage（V） Current Range（A） 20-80 20-100 Rate output voltage（V） Duty cycle（%） Efficiency（%） Power factor 0.93 0.93 Insulation Class Housing Protection Class IP21 IP21 Arcing Way Untouched Untouched Pressure of air compressor...
  • Page 6 Front Panel Instruction of I-PLAS25: Current meter Abnormal indicator Current selection knob Positive output terminal Negative output terminal Torch switch socket Pilot arc OWNER’S MANUAL - 5 - I-PLAS25/40...
  • Page 7 PANEL FUNCTION INSTRUCTION Front Panel Instruction of I-PLAS40: Power switch Current selection knob Abnormal indicator Current meter Negative output terminal Torch switch socket Pilot arc Positive output terminal OWNER’S MANUAL - 6 - I-PLAS25/40...

  • Page 8: Installation Instruction

    INSTALLATION INSTRUCTION The machine is equipped with power voltage compensation device. When the power voltage fluctuates between±15% of rated voltage, it still can work normally. When the machine is used with long cables, in order to prevent voltage form going down, bigger section cable is suggested.
  • Page 9 INSTALLATION INSTRUCTION Air regulator installation and operation Firmly tight and seal the copper air hole at IN and OUT terminal. By high pressure rubber tube firmly. Tight and seal the meter with meter face rubber tube. Fix the connecting shelf with screw as the regulator position. Get down the plastic screw and fix the regulator on the shelf.

  • Page 10: Notes Or Preventive Measures

    NOTES OR PREVENTIVE MEASURES 1. Environment 1） The machine can perform in environment where conditions are dry with a dampness level of max 90%. 2） Ambient temperature is between -10 to 40 degrees centigrade. 3） Avoid welding in sunshine or drippings. Do not let water enter the gas. 4）...
  • Page 11 QUESTIONS TO BE RUN INTO DURING CUTTING Fittings, welding materials, environment factor, supply powers maybe have something to do with welding. User must try to improve welding environment. A、 Cutting surface is rough, poor cutting result: The machine may be not well operated. You can check it as follow: ）, and its range Make sure the compressed air supply has enough pressure which is not less than 0.3MPa（3Kg/cm is±0.05Mpa.

  • Page 12: Maintenance

    MAINTENANCE WARNING： Power must be turned off for all checking and maintenance, before opening the housing, make sure the power plug is disconnected. Remove dust by dry and clean compressed air regularly, if welding machine is operating in environment where is polluted with smokes and pollution air, the machine need removing dust everyday.

  • Page 13: Troubleshooting And Fault Finding

    TROUBLESHOOTING AND FAULT FINDING Notes: The following operations must be performed by qualified electricians with valid certifications. Before maintenance,please contact with us for professional suggestion. Fault symptom and solutions of CUT 70: Fault symptom Remedy Switch indicator is on, fan is not working and 1.
  • Page 14 TROUBLESHOOTING AND FAULT FINDING Notes: The following operations must be performed by qualified electricians with valid certifications. Before maintenance,please contact with us for professional suggestion. Fault symptom and solutions of I-PLAS25/40: Faults Solutions 1. Make sure air switch is on. Meter can not display, fan can not 2.

This manual is also suitable for:

I-plas 40