1. Manuals
  2. Brands
  3. Amphenol Manuals
  4. Enclosure
  5. Charles CUBE-PM63915JN3
  6. General description and installation

Amphenol Charles CUBE-PM63915JN3 General Description And Installation

Universal broadband enclosure
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CUBE-PM63915JN3, CUBE-PM63915JN4,
CUBE-PM63915JN6, CUBE-PM63915JN7,
CUBE-PM63915JN8, and CUBE-PM63915JN9
1.
GENERAL INTRODUCTION ...................................................... 1
1.1. Document Purpose ................................................................... 1
1.2. Product Purpose ....................................................................... 1
1.3. Product Mounting and Location ............................................... 1
2.
PRODUCT DESCRIPTION ........................................................... 2
3.
INSTALLATION ............................................................................ 4
3.1. Inspecting the Product .............................................................. 4
3.2. Following and Using Safety Precautions.................................. 4
3.3. Obtaining Tools and Equipment ............................................... 4
3.4. Preparing the Installation Site .................................................. 4
3.5. Lifting the CUBE ...................................................................... 5
3.6. Mounting the CUBE ................................................................. 5
3.7. CUBE Wiring and Equipment .................................................. 6
3.8. Conduit Seals.......................................................................... 14
3.9. Verifying the Installation ........................................................ 14
4.
PERIODIC MAINTENANCE ...................................................... 15
5.
6.
WARRANTY & CUSTOMER SERVICE ................................... 15
7.
SPECIFICATIONS ....................................................................... 15
7.1. Regulatory Specifications ....................................................... 15
7.2. Product Specifications ............................................................ 16
7.3. Alarm Panel Settings .............................................................. 17

1. GENERAL INTRODUCTION

1.1. Document Purpose

This document provides general information for the CUBE-PM63915JN3/JN4/JN6/JN7/JN9 of the Charles Industries' Universal
Broadband Enclosure (CUBE) product line. Figure 1 shows a closed front view of the enclosure.
Hereafter, the Charles Universal Broadband Enclosure CUBE-PM63915JNx will be referred to as the "CUBE."

1.2. Product Purpose

This CUBE consists of a protective enclosure for an integrated system of electronic components and equipment that can serve fiber and
copper interfaces.

1.3. Product Mounting and Location

This enclosure is suitable for outside plant-type (OSP) locations and those that may require NEC compliance. The outdoor, weather-
resistant CUBE is to be mounted on a pad. The installer connects the power, fiber and copper connections. Detailed mounting and
installation information is covered in Section 3.
©Copyright 2024 Charles Industries LLC. All rights reserved.
Availability of features and technical specifications herein are subject to change without notice.
Charles is a registered trademark of Charles Industries.
Charles Universal Broadband Enclosure
General Description and Installation
Figure 1
-NOTE-
LT-PM63915JNX
6
Printing, November 18, 2024
th
Front View of the CUBE
Page 1 of 17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Charles CUBE-PM63915JN3 and is the answer not in the manual?

Questions and answers

Related Manuals for Amphenol Charles CUBE-PM63915JN3

Summary of Contents for Amphenol Charles CUBE-PM63915JN3

  • Page 1: Table Of Contents

    LT-PM63915JNX Printing, November 18, 2024 Charles Universal Broadband Enclosure CUBE-PM63915JN3, CUBE-PM63915JN4, CUBE-PM63915JN6, CUBE-PM63915JN7, CUBE-PM63915JN8, and CUBE-PM63915JN9 General Description and Installation GENERAL INTRODUCTION ............1 1.1. Document Purpose ..............1 1.2. Product Purpose ............... 1 1.3. Product Mounting and Location ..........1 PRODUCT DESCRIPTION ............

  • Page 2: Product Description

    LT-PM63915JNX 2. PRODUCT DESCRIPTION The CUBE is a single compartment with 39RU of rack space (12RU at 19”, 17RU at 23”) and a 4000BTU AC powered HVAC system with a 1000W AC powered heater (PM63915JN9 has two heaters). The PM63915JN3 and PM63915JN4 also have an Eltek power system. The PM63915JN3, PM63915JN7, and PM63915JN9 each have four battery trays, and each tray accommodates one string of customer supplied 12V 200Ah VRLA batteries.
  • Page 3 LT-PM63915JNX POWER SYSTEM LACING BAR (JN3 AND JN4 ONLY) ALARM PANEL GORE VENTS (BOTH SIDES) LOW TEMP THERMOSTAT JUNCTION BOX WITH GFCI AND HVAC POWER CABLE FITTING JUNCTION BOX WITH POWER CABLE FITTINGS FOR RECTIFIER 1 (TOP) AND RECTIFIERS PLINTH 2 AND 3 (REAR) DOOR ALARM AND WIND LATCH...

  • Page 4: Installation

    LT-PM63915JNX 3. INSTALLATION 3.1. Inspecting the Product The CUBE is shipped mounted upright on a skid. Remove the bolts, unpack the unit, and dispose of the packaging material. -INSPECTION NOTE- Visually inspect the unit for damages prior to installation. If the equipment was damaged in transit, immediately report the extent of the damage to the transportation company.

  • Page 5: Lifting The Cube

    LT-PM63915JNX 3.5. Lifting the CUBE See Table 1 for CUBE weight. Charles recommends the following procedure for lifting the CUBE. Prior to lifting, remove the lifting brackets that hold the mounting WARNING gasket in place. Set aside the gasket, and then replace the brackets. SPREADER BARS Failure to do so can result in a failure of the lifting bracket assembly.

  • Page 6: Cube Wiring And Equipment

    LT-PM63915JNX 3.6.2. Mounting the CUBE on a Pad Four customer supplied, corrosion resistant, 1/2”-13 hex head bolts with anchors are required for mounting the CUBE to the concrete pad. Use the following steps to mount the CUBE to a pad. Layout, drill, and set the 1/2”...
  • Page 7 LT-PM63915JNX Low Temp Low Temp Front and Rear Doors Front and Rear Doors (HVAC-1 Failure) (HVAC-1 Failure) Thermostat Thermostat Front and Rear Door Front and Rear Door WT/OR WT/OR To Alarm Panel To Alarm Panel HVAC Cutoff (Lef t ) HVAC Cutoff (Lef t ) (Door Intrusion) (Door Intrusion)
  • Page 8 LT-PM63915JNX Low Temp Low Temp To Alarm Panel To Alarm Panel Front and Rear Doors Front and Rear Doors Thermostat Thermostat (HVAC-1 Failure) (HVAC-1 Failure) Front and Rear Door Front and Rear Door WT/OR WT/OR To Alarm Panel To Alarm Panel HVAC Cutoff (Lef t ) HVAC Cutoff (Lef t ) (Door Intrusion)
  • Page 9 LT-PM63915JNX Low Temp Low Temp To Alarm Panel To Alarm Panel Front and Rear Doors Front and Rear Doors Thermostat Thermostat (HVAC-1 Failure) (HVAC-1 Failure) Front and Rear Door Front and Rear Door WT/OR WT/OR To Alarm Panel To Alarm Panel HVAC Cutoff (Lef t ) HVAC Cutoff (Lef t ) (Door Intrusion)

  • Page 10: Battery Tray

    LT-PM63915JNX All alarms are normally closed Overheat Overheat Low Temp Low Temp To Alarm Panel To Alarm Panel Thermostat Thermostat Thermostat Thermostat (HVAC-1 Failure) (HVAC-1 Failure) Front and Rear Doors Front and Rear Doors Front and Rear Door Front and Rear Door WT/OR WT/OR HVAC Cutoff (Lef t )
  • Page 11 LT-PM63915JNX All alarms are normally closed To Alarm Panel To Alarm Panel (HVAC-1 Failure) (HVAC-1 Failure) Front and Rear Door Front and Rear Door HVAC Cutoff (Left) HVAC Cutoff (Left) Overheat Overheat Low Temp Low Temp Thermostat Thermostat Dig Input 2 Dig Input 2 Thermostat Thermostat...
  • Page 12 LT-PM63915JNX All alarms are normally closed Overheat Overheat Low Temp Low Temp To Alarm Panel To Alarm Panel Thermostat Thermostat Thermostat Thermostat (HVAC-1 Failure) (HVAC-1 Failure) Front and Rear Doors Front and Rear Doors Front and Rear Door Front and Rear Door WT/OR WT/OR HVAC Cutoff (Lef t )

  • Page 13: Hvac Operation

    LT-PM63915JNX 3.7.2. Ground Connection Use the two 2x8 position ground bars provided in the CUBE for all grounding of internal equipment. External ground lugs are available on the rear of the CUBE for connecting a site ground wire. 3.7.3. -48VDC Power System (PM63915JN3 and PM63915JN4 Only) The power shelf has space for five rectifiers.

  • Page 14: Conduit Seals

    LT-PM63915JNX 3.7.9. Heater The 1000W AC powered heater turns on at 5⁰C and turns off at 15⁰C. These set points are not adjustable. The JN8 and JN9 models have two heaters. 3.7.10. Macro Alarm Terminal Panel An integrated macro-site alarm panel is mounted on the left wall of the cabinet. This panel provides forty protected dry contact alarm inputs to screw down terminals or 66-block connections (Figure 13).

  • Page 15: Periodic Maintenance

    LT-PM63915JNX 4. PERIODIC MAINTENANCE In the event that the enclosure needs to be opened in freezing conditions, a narrow, pointed metallic object such as a screwdriver or chisel, along with a non-metallic device like a rubber mallet, may be used to remove excessive ice buildup around the door and locking mechanism.

  • Page 16: Product Specifications

    LT-PM63915JNX 7.2. Product Specifications Physical Dimensions 80X”Hx32”Wx32”D Weight PM63915JN3: Approx. 440 lbs. as shipped PM63915JN4: Approx. 410 lbs. as shipped PM63915JN6: Approx. 390 lbs. as shipped PM63915JN7: Approx. 420 lbs. as shipped PM63915JN8: Approx. 375 lbs. as shipped PM63915JN9: Approx. 510 lbs. as shipped Equipment Rack Space and Hole Spacing 19”: 21”...

  • Page 17: Alarm Panel Settings

    LT-PM63915JNX 7.3. Alarm Panel Settings Alarm Number Description Door Intrusion Commercial Power Failure Surge Suppressor/Lightening Arrestor Rectifier Failure Multiple Rectifier Failure Battery Discharge Low Voltage DC Power Failure Generator Running CC10 Generator Low Fuel CC11 Generator Failure CC12 HVAC Failure CC13 High Temp CC14...

This manual is also suitable for:

Charles cube-pm63915jn4Charles cube-pm63915jn6Charles cube-pm63915jn7Charles cube-pm63915jn8Charles cube-pm63915jn9

Table of Contents