Advertisement
1. It enables the setting value of fridge to be modified and super cool mode to be activated
if desired. Freezer may be set to -16,-18,-20,-22,-24 °C, SF.
2. It is the Super Freeze mode symbol.
3. It is the alarm symbol.
4. It is the freezer set value screen.
Super Freezing Mode :
When would it be used?
• To freeze huge quantities of food.
• To freeze fast food.
• To freeze food quickly.
• To store seasonal food for a long time.
How to use?
• Press temperature set button until super freezing light comes on.
• Super freezing led will light during this mode.
• Maximum amount of fresh food (in kilograms) to be frozen within 24 hours is shown on the appliance
label.
• For optimal appliance performance in maximum freezer capacity, set the appliance to active SF mode
24 hours before you put the fresh food into the freezer.
During this mode:
If you press temperature set button, the mode will be cancelled and the setting will be restored from -16.
Note: Super freeze mode will automatically cancel after 54 hours, depending on the environmental
temperature or when the freezer sensor reaches a sufficiently low temperature.
FREEZER – 241
DISPLAY and CONTROL PANEL
2
1
4
3
1
APRIL 2022
Advertisement
Table of Contents
Related Manuals for VESTEL GT/SN482EGIDCKSB
Summary of Contents for VESTEL GT/SN482EGIDCKSB
- Page 1 FREEZER – 241 DISPLAY and CONTROL PANEL 1. It enables the setting value of fridge to be modified and super cool mode to be activated if desired. Freezer may be set to -16,-18,-20,-22,-24 °C, SF. 2. It is the Super Freeze mode symbol. 3.
-
Page 2: Display And Control Panel
FREEZER – 241 DISPLAY and CONTROL PANEL Freezer Temperature Settings • The initial temperature of the Setting Display is -18°C. • Press freezer setting button once. • Every time you press the button, the setting temperature will decrease. (-16°C, -18°C, - 20°C,.. -
Page 3: Fault Codes
FREEZER – 241 FAULT CODES Sensor short open circuit defect on display USER MODE SERVICE MODE SENSOR TEMPERATURE REACTION REACTION >+50°C or <-50°C (1) Freezer -16 Set Symbol blinks (sensor is short or open) (2) Refrigerator (3) Defrost Short (< 100W) or <-50°C -18 Set Symbol blinks (4) AT sensor Breakdown of (1) and (2) -
Page 4: Service Mode
FREEZER – 241 SERVICE MODE Entering service mode: Push SET button continuously for 10 seconds when -24 set symbol active. Appliance will enter service mode 10 sec. later. Canceling service mode: Push SET button continuously for 10 seconds when -24 set symbol active. Appliance will enter service mode 10 sec. -
Page 5: Troubleshooting Chart
FREEZER – 241 Trouble – Shooting Chart - 16 Control the Freezer sens. Is freezer Sensor Ok.? wire connections and connectors ok ? Replace Replace Correct it. sensor Board Control the Defrost Sensor Is Def. Sensor Ok.? wire connections and connectors ok ? Replace Replace... - Page 6 FREEZER – 241 Trouble – Shooting Chart Door/Gasket Adjustment Product Is the ground should be on under the a firm and flat unit is flat? surface Are the Adjust the feet adjustable properly feet in correct according to position? ground surface Is there any As a service misalignment at...
- Page 7 FREEZER – 241 Air Flow Diagram Cutaway view: Air Flow Direction Blown : Cold Air Returned: Hot Air APRIL 2022...
-
Page 8: Refrigerant Cycle
FREEZER – 241 Refrigerant Cycle Condenser Hot Gas Pipe Fin Evaporator Capillary Tube Dryer Compressor This model is double controlled product without any valves. When both cooler & freezer sections are set by end user, mainboard controls both the cooler sensor &... - Page 9 FREEZER – 241 CHANGING THE DOORWAY DIRECTION APRIL 2022...
- Page 10 FREEZER – 241 CHANGING THE DOORWAY DIRECTION APRIL 2022...
- Page 11 FREEZER – 241 CHANGING THE DOORWAY DIRECTION APRIL 2022...
- Page 12 FREEZER – 241 ASSEMBLE & DISASSEMBLE OF AIR DUCT Warning: Make sure the unit is unplugged. 1. Remove the refrigerator glass shelves and the flap cover supports left and right. 2. Remove the plugs by pulling them under the base with a pointed device to remove the screw plugs and remove the screws.
- Page 13 FREEZER – 241 Removing- Assembling The Freezer Fan 1. After remove the fan motor connector, airduct can be displaced. 2. Unscrew the airduct fixing screws and Get rid of the nails carefully. APRIL 2022...
- Page 14 FREEZER – 241 Removing- Assembling The Freezer Fan (Radyal) 3. After remove the airduct cover, to displace the fan motor get rid of the the nail by using needlenose pliers. APRIL 2022...
- Page 15 FREEZER – 241 Removing- Assembling The Fin Evap. Warning: This process needs gas deflation, gas re-charging and welding processes so its need to be done by trained professionals. 1. Take out the fin evap heater (blue) connector and remove the bitumen covering the tubes. Warning: Before cutting the tube follow make sure the gas is evacuated.
- Page 16 FREEZER – 241 Removing- Assembling The Head Panel Display Warning: Make sure the unit is unplugged. 1. By aid of a flat screwdriver or smilar tools remove taps and then unscrew 2. Unhook snapfits on the head panel by reaching from related cavities and pull head panel backward 3.
- Page 17 FREEZER – 241 Removing- Assembling The Reed Switch Take the reed switch out of its place with a screwdriver. Then Disconnect the connectors of the Switch and remove it. NOTE: Reed Switch is a very sensitive miniature electronic card. So during the assembly and disassembly be carefull not to damage it.
- Page 18 FREEZER – 241 Barcode and Serial Number Explanation: Vestel refrigerator serial numbers are consist of 22 digits. DOOR COUNTRY DESIGN BRAND ENERGY CLASS VESTEL MODEL MONTH YEAR SERIAL NUMBER Cabinet Packaging Type Product Number of Type the party 1-Carton 2-Shrink...
Need help?
Do you have a question about the GT/SN482EGIDCKSB and is the answer not in the manual?
Questions and answers