Advertisement
Quick Links
PNEUMATIC RIVET NUT SETTER
Professional model of air riveter to install blind rivets.
Professional model of air riveter to install blind rivets.
Thank you very much for purchasing "LOBSTER" air riveter. To ensure correct operation, please read
this instruction manual carefully, and keep it in a safe place for later reference.
Thank you very much for purchasing "LOBSTER" air riveter. To ensure correct operation, please read
Professional model of pneumatic rivet nut setter to install blind rivet nuts.
this instruction manual carefully, and keep it in a safe place for later reference.
Thank you very much for purchasing" ＬＯＢＳＴＥＲ "pneumatic rivet nut setter. To ensure correct
operation, please read this instruction manual carefully, and keep it in a safe place for later reference.
This is Original instructions.(Original Instruction
Manual iswritten in English language.)
MANUFACTURER
MANUFACTURER
International Marketing&Sales Division
12-8 Shijo-cho, Higashi-Osaka City
Osaka 579-8053, Japan
Telephone: +81(72)981-7466 Telefacs: +81(72)981-9420
URL http://www.lobtex.co.jp/
AIR RIVETER
AIR RIVETER
INSTRUCTION MANUAL
INSTRUCTION MANUAL
INSTRUCTION MANUAL
MANUFACTURER
BUILT-IN ON-DEMAND
VACUUM SYSTEM
Ｎ１Ａ２
R1A1
R1A1
CONTENTS
INTRODUCTION.....................１
CONTENTS
CONTENTS
IMPORTANT SAFETY
............２
I N S T R U C T I O N S
IMPORTANT SAFETY
INSTRUCTIONS.................................1
NOMENCLATURE.................. ５
IMPORTANT SAFETY
INSTRUCTIONS.................................1
NOMENCLATURE .............................3
TECHNICAL DATA.................. ６
NOMENCLATURE .............................3
TECHNICAL DATA ...........................4
PREPARATION BEFORE USE...７
TECHNICAL DATA ...........................4
PREPARATION BEFORE USE .......5
OPERATING THE PNEUMATIC
PREPARATION BEFORE USE .......5
OPERATING THE AIR RIVETER ....7
RIVET NUT SETTER
OPERATING THE AIR RIVETER ....7
MAINTENANCE
MAINTENANCE .................................8
MAINTENANCE .................................8
STORAGE........................................12
TROUBLESHOOTING............１６
STORAGE........................................12
PARTS TABLE ................................13
PARTS TABLE .....................１７
PARTS TABLE ................................13
ORDERING PARTS .........................14
STORAGE ･........................２２
ORDERING PARTS .........................14
TROUBLESHOOTING .....................15
TROUBLESHOOTING .....................15
ORDERING PARTS...............２２
BUILT-IN ON-DEMAND
VACUUM SYSTEM
...１３
...............１４
PRINTED IN JAPAN
PRINTED IN JAPAN
PRINTED IN JAPAN
Advertisement
Related Manuals for LOBSTER N1A2
Summary of Contents for LOBSTER N1A2
- Page 1 Professional model of air riveter to install blind rivets. Professional model of air riveter to install blind rivets. Thank you very much for purchasing “LOBSTER” air riveter. To ensure correct operation, please read this instruction manual carefully, and keep it in a safe place for later reference.
- Page 2 handling this tool, replacing accessories or replacing parts as needed. ・ If you have any questions about this manual, check the model (type) and contact the “LOBSTER” dealer where you purchased the tool. ・ It is impossible to foresee all potential dangers and describe them in this manual.
-
Page 3: Important Safety Instructions
●安 ●安全上のご注意 ●安全上のご ●安全上のご注意 IMPORTANT SAFETY INSTRUCTIONS ●安全上のご注意 ● IMPORTANT SAFETY INSTRUCTIONS ◆ ご使用前に、この「安全上のご注 ●安全上のご注意 ください。 ●安全上のご注意 ●安全上の ◆ Be sure to read the following Important Safety Instructions carefully and make sure that you ◆ ご使用前に、この「安全上のご注意」すべてをよくお読みのうえ、十分理解されて正しく使用して ◆ ご使用前に、この「安全上のご注意」すべてをよくお ◆ ご使用前に、この「安全上のご注意」すべてをよくお読みのうえ、十分理解されて正しく使用して ◆... - Page 4 ・修理は必ずお買い求めの販売店、または当社にお出しください。修理の知識や技術のない方が ・ Repair work should only be carried out by a qualified technician. Please contact your nearest 修理されますと、十分な性能を発揮しないだけでなく、事故やけがの恐れがあります。 "LOBSTER" distributor, representative, or direct to Lobtex Co.,Ltd.,Osaka. If the tool is repaired 15. 本機の改造をしないでください。 by someone without the necessary qualifications and experience, the tool may not perform to ・異常動作等事故やけがの恐れがあります。...
- Page 5 注 意 CAUTION １５.The year and month of production of the tool are indicated by a code and four-digit number on the 1. 本機のお手入れ、部品交換等の分解時には必ずエアーの供給を止めてください。 cylinder cap (see page 6). ~~~~~~~~~~~~~~~ ・エアーが供給された状態で手入れや分解を行なうと、部品の飛び出し、オイルのふき出し、予期 １６.Warning labels include important information and tips on using the tool. If the labels become so dirty せぬ動きなどにより、事故や傷害を負う恐れがあります。...
- Page 6 ● NOMENCLATURE Frame head Frame Screw mandrel M6 Nosepiece M6 Bleed plug Switch Stroke adjuster lock sleeve Nosepiece lock nut Reverse button ■ ＡＣＣＥＳＳＯＲＩＥＳ ■ Check at the time of purchase. 公差表示方式JIS B 0024 尺度 材質 制定日 普通公差 JIS B 0419-mH 20℃・65％・101.3kPa 寸法公差...
- Page 7 ↓ （Serial No.） Revision history of instruction manual Item ： Pneumatic rivet nut setter Model ： N1A2 Date of first edition: August , 2015 NY ○○○○ Date of second edition: November , 2015 Date of third edition: February , 2016...
- Page 8 ※ご使用中は必ずタンクケースユニットを取付けてお使いください。タンクケースユニットを取付けずに バキュームボタンをＯＮにすると、切断されたリベットのマンドレルが勢い良く飛び出し、傷害を及ぼ ● PREPARATION BEFORE USE す恐れがあります。 コンプレッサーを用意しエアーリベッター Air regulator レギュレータ との 間に必ずエアーフィルタ ・ レギュレー エアー Set up the compressor, and １ １ Air filter ~~~~~~~~~~~~~~~~ フィルタ タ ・エアールブリケータ （3点セット） を取り be sure to install an air filter, ~~~~~~~~~~~~~~~~~~~~ air regulator and air lubricator 付けてください。...
- Page 9 ください。 ◆ 本機をご使用中は、必ず保護めがねを着用してください。切断されたリ 出し傷害を及ぼす恐れがあります。 How to replace the screw mandrel and nosepiece 警 告 注 意 ◆ ここに示した注意事項は と に区分けしていますが、 それ Nosepiece base 警 告 １ Remove the nosepiece. ：誤った取扱いをした場合、使用者が死亡または重傷を負う Nosepiece のご注意 ※ Always turn off the air supply before replacing parts. 注...
- Page 10 Suppose the fastener used is “Lobster” NSK-6M, to be installed in Always apply grease to the collar of the 1.0mm material thickness. The stroke (pull-up) needed is 3.5mm, as...
- Page 11 How to adjust stroke Stroke adjusting Stroke adjusting dial dial lock sleeve １ Adjustment of stroke Adjust the stroke to each rivet nut setting capacity. Slide this way. Turn the stroke adjusting dial and slide the stroke adjusting dial lock sleeve in the direction of the arrow to adjust the stroke.
- Page 12 Repeat steps to until the stroke becomes ±0.3 mm of the appropriate stroke. ６ ※ To operate the air motor smoothly, lubricate with 3 - 5 drops of LOBSTER hydraulic oil “B10012” (optional) from the air coupler before starting work. １１...
- Page 13 １ Precautions when using the Pneumatic rivet nut setter ６ Worn or damaged threads in the screw mandrel (mandrel) prevents proper use. Pay close attention to M3 to M5 mandrels, since they are thin and vulnerable to damage. Observe the following. ①...
- Page 14 ● OPERATING THE PNEUMATIC RIVET NUT SETTER １ １ Drill a hole of the appropriate size into the workpiece. Push a rivet nut into the screw mandrel to load it. １ ２ Without pulling the switch, the screw mandrel automatically rotates in the clockwise direction and loads the rivet nut as the screw mandrel is pushed inward. ...
- Page 15 と に区分けしていますが、 そ ◎ If the tool runs low on hydraulic oil and does not produce an adequate stroke, lubricate the tool with LOBSTER hydraulic oil “B10012” (optional) by following the procedure below. If stroke is again 警 告 ：誤った取扱いをした場合、使用者が死亡または重傷を負...
- Page 16 Apply grease to the O-ring and rod of air piston unit １ ７ and to the inside of cylinder cup using brush. Apply grease Air piston unit Cylinder cup Apply grease １ Push the air piston unit into the oil supply ８...
- Page 17 If a problem occurs, check the followings. If the problem persists after checking the items in the table below, contact your nearest ‘’LOBSTER’’ dealer or direct to us. In making any enquiries about this product or requests for repair work, first check the troubleshooting items below, and then make a note of the model number, the usage conditions and the trouble symptoms in as much detail as possible.
- Page 18 ● PARTS TABLE １７...
- Page 19 Index Code Index Code Part name Material Part name Material Ｎｏ． Ｎｏ． Ｎｏ． Ｎｏ． Frame 64892 Aluminum ３３ Air motor cover RH 64916 Plastic １ Cylinder cup 64921 Aluminum ３４ O-ring P-14 10434 Rubber ２ Cylinder cap unit 64882 ３５ B-ring P-14 10435 Plastic ３...
- Page 20 Cylinder cap unit （64882） １９...
- Page 21 Index Ｎｏ． Part name Code Ｎｏ． Material Spool cap 64895 Aluminum １ O-ring S-12 23709 Rubber ２ Spool spring 64918 Steel ３ Spool axis 40474 Aluminum ４ O-ring P-9 10219 Rubber ５ Hexagon socket head cap set screw M5×5 64960 Steel ６...
- Page 22 Air piston unit （64883） １ Index Part name Code Ｎｏ． Material Ｎｏ． Cushion rubber 63178 Rubber １ ２ O-ring 0750G 64962 Rubber ２ Spool connector unit （64887） ６ １ ２ ３ ４ ５ Index Code Part name Material Ｎｏ． Ｎｏ． O-ring S-10 10151 Rubber...
- Page 23 Use only clean hydraulic oil, as the viscosity of the oil used will affect tool performance. ''LOBSTER'' brand Hydraulic Oil is supplied in a plastic filler bottle with the tool, and can also be obtained from your ''LOBSTER'' dealer or agent in your town. If this is not possible, a good quality mineral oil with the following properties should also be used.
- Page 24 WARRANTY & SERVICE WARRANTY & SERVICE LOBSTER WAR R ANTS THAT GO O D S C O VE RE D BY THIS ○ MANUAL WILL CONFORM TO APPLICABLE SPECIFICATIONS A N D D R A W I N G S A N D T H A T S U C H G O O D S W I L L B E LOBSTER WARRANTS THAT GOODS COVERED BY THIS ®...
Need help?
Do you have a question about the N1A2 and is the answer not in the manual?
Questions and answers