Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for REVELL Aurora
Summary of Contents for REVELL Aurora
- Page 1 Revel Aurora Sauna PRODUCT MANUAL...
-
Page 2: Table Of Contents
Contents Introduction Safety Wood and Expectations Tools & Parts List Foundation Oiling the Aurora Barrel Assembly Instructions 6-13 Front and Back Edge Accessories and General Information Heater Use Sauna Stones Oiling Cleaning and Use Mould Cause and Prevention Treatment of Mould... -
Page 3: Introduction
INTRODUCTION Congratulations on your purchase of our Revel Traditional Finnish Barrel Sauna! You’re on the path to enhanced well-being and health. Thousands of users experience the benefits of saunas daily, and now you can enjoy the soothing effects in the comfort of your own home. Please take the time to read this manual carefully before your first use. -
Page 4: Tools & Parts List
TOOLS PROVIDED PLASTIC HAMMER × 1 SILICONE GUN SILICONE TOOLS REQUIRED ADJUSTABLE POWER DRILL TAPE MEASURE NAIL GUN WRENCH UTILITY KNIFE LADDER LEVEL PARTS LIST... -
Page 5: Foundation
FOUNDATION RECOMMENDATIONS Ensure the foundation is capable of supporting the weight of the Aurora Sauna (450 kg) without sinking or shifting We recommend using a concrete slab or a pile foundation. The base of the sauna should not be placed directly on surfaces like soil or grass, as they can compromise the quality of the timber. - Page 6 ASSEMBLY INSTRUCTIONS - BASE FRAME 1. Place the 2 base frames on the ground 2. Locate the wooden stave with drain holes and secure it in the middle of the 2 base frames. Tip: Ensure base is level by measur- ing on the diagonal - both measurements should match 3.
- Page 7 ASSEMBLY INSTRUCTIONS - BASE FRAME A. Position and align the back centre panel precisely within the channel of the staves. B. Position the left and right back panels to connect seamlessly with the centre panel. C. Fix the 3 panels together with screws. A.
- Page 8 ASSEMBLY INSTRUCTIONS - BARREL STAVES A. Start on the left side of the barrel and place each stave in position, tap firmly into place with the Rubber Mallet until half way up on the left side - fix each stave in place by screw- ing or nailing the stave against the front and back panel.
- Page 9 ASSEMBLY INSTRUCTIONS - BARREL STAVES 8. Place the 2 stainless steel straps around the the barrel and tighten firmly to secure the staves in place. Tip: Position bolts on the Stainless straps on the bottom half of the sauna to allow the Cedar shingles to sit flush on the roof.
- Page 10 ASSEMBLY INSTRUCTIONS - BARREL FLOORING 10. Place and secure the floor in A. Place and secure the place with screws. Door handle in place. B. Place and secure the inside Door handle in place. C. Fix the cup holder to the front inside wall.
- Page 11 ASSEMBLY INSTRUCTIONS - SHINGLES & FASCIA 13. Secure the first fascia plate at the centre using two screws, then continue attaching the re- maining fascia plates until reaching the halfway point. Do the same on the back of the Barrel. 14.
- Page 12 ASSEMBLY INSTRUCTIONS - SHINGLES & FASCIA 15. For accurately overlapping & laying the second and subsequent shingles a ‘jig’ or ‘template’ should be made and used as seen below. 16. Continue laying and overlapping the 17. At the top of the barrel, the spacing may shingles, stopping just before reaching be slightly uneven, resulting in a gap on the peak of the barrel.
-
Page 13: Assembly Instructions
ASSEMBLY INSTRUCTIONS - HEATER 12. The Harvia heater includes a wall mount, and detailed instructions for installing the mounting plate and heater can be found in the Harvia manual. Only a certified Electrician should install the Harvia Heater. -
Page 14: Front And Back Edge
FRONT AND BACK EDGE To prevent moisture and rainwater from accumulating on the front and back edges of the sauna, we recom- mend applying a bead of silicone where the front and back panels meet the timber slats, starting halfway up the barrel and continuing around to the other side. -
Page 15: Sauna Stones
SAUNA STONES The use and proper care of stones are essential to enhancing your sauna experience. For optimal results, please follow these guidelines: 1. Once your electrician has wired and tested your Har- via heater to ensure it’s receiving power, turn the heat- er on without placing any stones. -
Page 16: Oiling
OILING To ensure longevity and uphold your sauna’s warranty, it’s essential to regularly treat all external wooden surfaces (except beneath the tiles) with a UV-protectant timber oil to safeguard against the harsh Australian climate. As a natural wood product, the timber requires re-oiling every 3-6 months, depending on its location and exposure to sunlight. -
Page 17: Cleaning And Use
CLEANING AND USE When using the sauna, it’s a good practice to place towels on both the seat and the floor beneath you. This helps maintain cleanliness and protects the timber from sweat-related damage. For cleaning, we recommend using a cloth dampened with a mild vinegar and water solution. Ad- ditionally, we strongly advise regularly removing the floor panel to clean the bottom of the barrel, as dirt and moisture can accumulate over time. -
Page 18: Maintenance And Cleaning Schedule
MAINTENANCE The timber in your sauna has been treated to enhance its thermal performance but remains a porous, reactive material that may change visually with regular use. Exposure to heat, moisture, and the elements can cause the wood to swell or shrink, leading to small surface-level splits or gaps. -
Page 19: Warranty
This warranty is a limited warranty given by Rev- If the Revel Wellness after sales service team is el Wellness for the Revel Aurora Barrel Sauna and not able to resolve the issue or the customer is not is valid for the period of 5 years from the date of able or willing to work with them, Revel Wellness delivery. - Page 20 Live Longer, Live Better...
Need help?
Do you have a question about the Aurora and is the answer not in the manual?
Questions and answers