Subscribe to Our Youtube Channel
Related Manuals for infobit iSwitch 2000D-WPT
Summary of Contents for infobit iSwitch 2000D-WPT
- Page 1 2000D-WPT (US-2Gang version) JPEG2000 4K60 AV over IP 1GbE Encoder (Wall-plate) with KVM Function VER 1.0 www.infobitav.com info@infobitav.com...
-
Page 2: Table Of Contents
Thank you for purchasing this product For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lighting strikes, etc. -
Page 3: Introduction
1. Introduction This 4K60 AV over IP 1GbE Encoder (Wall-plate) is based on JPEG2000 technology, and uses ASPEED AST1530 for image codec and low-latency KVM applications. It features HDMI and USB-C dual input, with a video resolution of up to 4K60 4:4:4. This product supports audio embedding and de-embedding function, as well as USB 2.0/KVM/Camera, 1G Ethernet, bi- directional RS-232 (pass-through &... -
Page 4: Package Contents
☆ Audio embedding and de-embedding are supported ☆ Dante AV-A mode is supported if license activated ☆ Support unicast and multicast functions ☆ Support point-to-point, video matrix and video wall functions (video wall supports up to 9x9) ☆ Intelligent video wall class management ☆... -
Page 5: Specifications
4. Specifications Technical HDMI Compliant HDMI 2.0b HDCP Compliant HDCP 2.2 Video Bandwidth 18Gbps USB Bandwidth 480Mbps Video Compression JPEG2000 Standard Video Network Bandwidth 640x480p60Hz, 800x600p60Hz, 1024x768p60Hz, 1280x1024p 60Hz, 1360x768p60Hz, 1440x900p60Hz, 1440x1050p60Hz, 1600x1200p60Hz, 720x480i59.94Hz(480i59), 720x480p59.94Hz (480p59), 720x576i50Hz(576i50), 720x576p50Hz(576p50), 1280x720p50Hz (720p50), 1280x720p59.94Hz(720p59), 1280x720p60Hz(720p60), 1920x1080i50Hz(1080i50), 1920x1080i59.94Hz(1080i59), 1920x1080i60Hz(1080i60), 1920x1080p23.98Hz(1080p23), 1920x1080p24Hz(1080p24),... - Page 6 Input/Output Impedance >=10k ohms/330 ohms Line Input/Output Level 1Vrms/1Vrms (Maximum) Analog Input/ Frequency Response (+0.5dB, -1dB) 20Hz ~ 20kHz Output Audio Audio Output Sync Delay TBD Parameters >90dB@ HDMI 0dB, 1kHz A-weighted Audio S/N Ratio <0.05%@ HDMI 0dB, 1KHz Audio THD+N IEC 61000-4-2: ESD Protection ±15kV (Air-gap discharge) &...
- Page 7 Mechanical Encoder: Aluminum panel + Iron case Housing Decoder: Metal enclosure Encoder: White panel + Black case Color Decoder: Black Encoder: 115.9mm [W] x 114.3mm [H] x 44.25mm [D] Dimensions Decoder: 204mm [W] x 136mm [D] x 25.5mm [H] Encoder: 350g Weight Decoder: 626g Input: AC100 - 240V 50/60Hz,...
-
Page 8: Operation Controls And Functions
5. Operation Controls and Functions 5.1 Encoder Panel Name Function Description Connection status indicator light. ▪ Light on: Encoder and Decoder are connected through the LAN(PoE) port, and there is video signal transmitted to the Decoder. STATUS LED ▪ Light flashes: Encoder and Decoder are connected through (Green) the LAN(PoE) port, but there is no video signal transmitted to the Decoder. - Page 9 Name Function Description ▪ Short press to switch the input signal source (HDMI/USB-C) ▪ Press and hold the button for 5 seconds to restore the unit to factory default settings (The STATUS, USB-C and HDMI LEDs will simultaneously light off/on, quickly flash 3 times to SOURCE button indicate the resetting).
-
Page 10: Decoder Panel
5.2 Decoder Panel Name Function Description After powering on the device, press and hold the RESET button until the POWER LED and LINK LED flash at the same RESET time, release the button to reset the device to factory settings. ▪... -
Page 11: Audio In/Out
Name Function Description VCC: Power output (12V or 5V configurable), maximum to 12V @50mA, 5V@ 100mA loading. The default output is 12V. RELAYS: 2 channel low-voltage relay ports, each group is independent and isolated, maximum to 1A 30VDC loading. Contacts are disconnected by default. DIGITAL IO: 2 channel GPIO ports, for digital level signal output control or input detection (up to 12V level detection). -
Page 12: Mjpeg Substream Operation Introduction
Name Function Description Link Signal ▪ Light on: The network cable is connected normally. Indicator lamp ▪ Light off: The network cable is not connected well. (Green) The device can be powered via two methods: ▪ Local DC 12V/2.5A power supply 19 DC 12V ▪... - Page 13 Step 2: Install a bonjour protocol checking tool (such as zeroconfService Browser) on PC to find the IP address of the Encoder/Decoder. Take zeroconfServiceBrowser as an example. After opening the software, you can select “Workgroup Manager” in Services of Browser, select the Host name in Service-Instances, and find the IP address in the Address item in of Instance-Info.
- Page 14 Step 4: According to the IP address of the Encoder/Decoder found through the bonjour protocol checking tool, input “http://IP:PORT/?action=stream” into the web browser on PC. The MJPEG Substream will be displayed with the default resolution, as shown in the figure below. 12 / 19...
- Page 15 Step 5: Change the resolution of the obtained Encoder/Decoder IP address in the following format. http://IP:PORT/?action=stream&w=x&h=x&fps=x&bw=x&as=x&mq=x WIDTH: [Optional] image width. In pixels. ‘x’ means no change. ▪ Default is 640. HEIGHT: [Optional] image height. In pixels. ‘x’ means no change. ▪...
-
Page 16: Vlc Media Player Instruction
6.2 VLC Media Player Instruction Firstly, perform the step 1~3 as described in Chapter 6.1, then open the VLC media player on PC. Please see the following icon. Click “Media > Open Network Stream” After clicking the “Open Network Stream” option, the following page will appear. - Page 17 Enter the MJPEG Substream network URL, then click “Play” button. Choose “Tools>Codec information”, a pop-up window will display and show you Stream information, as shown in the figure below. 15 / 19...
- Page 18 Choose “Tools>Codec information>Statistics” to check current Bitrate. Please see the following picture. Note: The Bitrate is floating up and down when you check it. This is a normal phenomenon. 16 / 19...
-
Page 19: Switch Model
7. Switch Model A network Switch used to set up the system should support below features: 1. Type of layer 3/managed network Switch. 2. Gigabit bandwidth. 3. 8KB jumbo frame capability. 4. IGMP snooping. The following Switch models are highly recommended. Manufacturer Model Number CISCO... -
Page 20: Application Example
9. Application Example Controller Box Laptop Router (optional) 1G Ethernet Switch TV Box 4 × DEC Media Player Video Wall Desktop Computer The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. - Page 21 Notes: (1) The Controller has two LAN ports, one is Video LAN and the other one is Control LAN. The purpose of designing Controller with two LAN ports is to isolate audio/video (AV) network from control network. So to make AV network as an independent network which can not be accessed from control network directly, it's for bringing network security and avoiding AV network traffic flowing into the network in which the controls and managements are...
Need help?
Do you have a question about the iSwitch 2000D-WPT and is the answer not in the manual?
Questions and answers