1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Tiller
  5. 9430FH
  6. Operator's manual

Landoll 9430FH Operator's Manual

Field cultivator
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
'
Model 9430FH
Field Cultivator
Operator's Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-1136-2501

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 9430FH and is the answer not in the manual?

Questions and answers

Related Manuals for Landoll 9430FH

Summary of Contents for Landoll 9430FH

  • Page 1 ‘ Model 9430FH Field Cultivator Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1136-2501...

  • Page 2: Instructions For Ordering Parts

    The identification plate, which lists the model number and serial number, is located on the front of the frame. SERIAL NUMBER The serial number is located on the identification plate. The Following information will help decode the 9430FH Field Cultivator serial number 94H232000 = xxmyysssss QR CODE DECAL...
  • Page 3 DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
  • Page 5 Rephasing Hydraulic Cylinder Change ......3-10 Cross Reference Matrix For Model 9430FH FC ..... . . 3-11 Hydraulic Installation.
  • Page 6 9430FH Gauge Wheels ........

  • Page 7: Introduction And Safety Information

    Introduction and Safety Information The Landoll Model 9430FH Field Cultivator is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.

  • Page 8: Understanding Safety Statements

    5. Use a locking-style hitch pin that properly fits the The safety statements contained in this manual relate to tractor drawbar and the implement hitch. Lock the the operation of the Model 9430FH Field Cultivator. tractor drawbar in the center position to prevent loss of steering control.
  • Page 9 TABLE OF CONTENTS 6. Attach the safety chain to the tractor recommended 5. Install hydraulic cylinder lockouts, or lower equipment drawbar support. Provide only enough slack in the to the ground before servicing. chain for turning. Do not attach the safety chain to an High Pressure Fluid Safety intermediate support.

  • Page 10: Tire Safety

    TABLE OF CONTENTS Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment.
  • Page 11 Safety Decals and Reflectors New safety signs may be ordered from your Landoll dealer. Refer to this section for parts and proper safety The 9430FH Field Cultivator is equipped with all safety sign placement. signs installed for safe operation. To Install new safety signs: For you safety: 1.
  • Page 12 TABLE OF CONTENTS P/N 144193 SIS 20MPH Front of center frame extension, middle QTY. 1 P/N 2-573-010037 Danger: Folding wing Front side, front hinge plate, center frame extension, both sides QTY. 2 P/N 2-573-010037 Danger: Folding wing Back side, rear hinge plate, center frame, both sides QTY.
  • Page 13 TABLE OF CONTENTS P/N 528934 Yellow Reflector Left front, amber light bracket, both sides QTY. 2 P/N 528934 Yellow Reflector Left rear, center lift plate, both sides QTY. 2 P/N 528938 Orange Reflector Back side, light brackets, top, both sides QTY.
  • Page 14 TABLE OF CONTENTS P/N 224589 SIS 20 mile/h Back side of SIS 20MPH mount plate QTY. 1 P/N 70260977 SMV Emblem Back side, SMV mount plate QTY. 1 P/N 231488 Caution: Maximum Hitch Weight CAUTION MAXIMUM HITCH WEIGHT 1000 LBS 231488 Back side of rear tow hitch QTY.

  • Page 15: Specifications

    10 days of purchase or lease, in so as to be able to follow the suggestions made. Please order to be on file at Landoll and eligible for Warranty. take time to understand the proper maintenance schedule and SAFE operation of your equipment.
  • Page 16 Landoll Company, LLC Warranty Department within ten (10) days of the first retail sale. As stated above, Landoll Company, LLC Warranty Staff will identify components listed on a Warranty Claim required to be returned for further analysis. All parts returned to Landoll Company, LLC must be shipped with a Return Materials Authorization (RMA) provided by the Landoll Company, LLC Warranty Staff.
  • Page 17 This exclusive remedy shall not be deemed to have failed of its essential purpose so long as Landoll Company, LLC is willing and able to repair or replace defective parts in the prescribed manner.

  • Page 18: General Torque Specifications

    TABLE OF CONTENTS General Torque Specifications LANDOLL SAE TORQUE SPECIFICATIONS (FOOT POUNDS) [ ] Indicates specifications for Prevailing Torque Nuts. FASTENER TORQUE SPECIFICATIONS (Rev. 23/04) This chart provides general torque specifications for UNF Size Grade 2 Grade 5 Grade 8...

  • Page 19: Hydraulic Fitting Torque Specifications

    TABLE OF CONTENTS Hydraulic Fitting Torque Specifications LANDOLL LANDOLL LANDOLL HYDRAULIC FITTING TORQUE HYDRAULIC FITTING TORQUE HYDRAULIC FITTING TORQUE SPECIFICATIONS SPECIFICATIONS SPECIFICATIONS (REV . 23/04) (REV . 23/04) (REV . 23/04) AEROQUIP BRAND FITTINGS GATES BRAND FITTINGS PARKER BRAND FITTINGS 37°...

  • Page 20: Model Specifications

    TABLE OF CONTENTS Model Specifications 9430FH Field Cultivator Model Number 9430FH -30 9430FH -32 9430FH -34 Working Width 30'-4” 32'-4” 34'-4” Transport Width 17’-4” 17’-4” 17’-4” Transport Height 13’-0” 13’-10” 14’-10” Number of Shanks Shanks per Section 26-39-26 29-39-29 32-39-32 3”...
  • Page 21 TABLE OF CONTENTS Table provided for general use. NOTES:...
  • Page 22 18” 12” 6” 4” 2” 4” 4” 12” 12” 10” 32’ 4” 10” 18” 10” 2” 2” 1-3/4” 20” 2” 2” 2” 34’ 14” 8” 8” 14” 14” 14” 8” 8” 14” 30’ Figure 2-6: Shank Placement 9430FH LH F-1136-2501...
  • Page 23 18” 6” 12” 2” 4” 12” 12” 4” 6” 32’ 10” 4” 20” 18” 2” 2” 1-3/4” 4” 2” 2” 2” 34’ 26” 26” 14” 8” 8” 8” 14” 14” 8” 8” 14” 30’ Figure 2-7: Shank Placement 9430FH RH...
  • Page 24 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 10 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-8: 3 Row Tine & Reel Placement 9430FH -30’ LH 2-10 F-1136-2501...
  • Page 25 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 10 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-9: 3 Row Tine & Reel Placement 9430FH -30’ RH 2-11...
  • Page 26 7 TINE 3 ROW 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-10: 3 Row Tine & Reel Placement 9430FH -32’ LH 2-12 F-1136-2501...
  • Page 27 ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-11: 3 Row Tine & Reel Placement 9430FH -32’ RH 2-13...
  • Page 28 8 TINE 3 ROW 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY HARROW ASSEMBLY 120” REEL ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-12: 3 Row Tine & Reel Placement 9430FH -34’ LH 2-14 F-1136-2501...
  • Page 29 ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW 8 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY 120” REEL ASSEMBLY Figure 2-13: 3 Row Tine & Reel Placement 9430FH -34’ RH 2-15...
  • Page 30 6TH HOLE 6TH HOLE 11TH HOLE 14-7/8” 15-5/8” 11-3/4” 12-7/8” 12 TOOTH SPIKE 9 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-14: 3 Row Spike and Reel Harrow Placement 9430FH -30’ LH 2-16 F-1136-2501...
  • Page 31 7TH HOLE 10TH HOLE 9TH HOLE 10TH HOLE 15-5/8” 12-7/8” 11-3/4” 14-7/8” 9 TOOTH SPIKE 12 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-15: 3 Row Spike and Reel Harrow Placement 9430FH -30’ RH 2-17...
  • Page 32 9TH HOLE 7TH HOLE 9TH HOLE 7-3/4” 12-3/8” 19-1/4” 6-1/4” 13 TOOTH SPIKE 9 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-16: 3 Row Spike and Reel Harrow Placement 9430FH -32’ LH 2-18 F-1136-2501...
  • Page 33 4TH HOLE 13TH HOLE 7TH HOLE 11TH HOLE 10-1/2” 7-3/4” 19-1/4” 12-3/8” 10 TOOTH SPIKE 13 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-17: 3 Row Spike and Reel Harrow Placement 9430FH -32’ RH 2-19...
  • Page 34 9TH HOLE 6TH HOLE 9TH HOLE 14-7/8” 6-7/8” 19-1/4” 6-1/4” 14 TOOTH SPIKE 9 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 120” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-18: 3 Row Spike and Reel Harrow Placement 9430FH -34’ LH 2-20 F-1136-2501...
  • Page 35 4TH HOLE 13TH HOLE 6TH HOLE 10TH HOLE 6-7/8” 10-1/2” 19-1/4” 14-7/8” 10 TOOTH SPIKE 14 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 120” REEL ASSEMBLY Figure 2-19: 3 Row Spike and Reel Harrow Placement 9430FH -34’ RH 2-21...
  • Page 36 5TH HOLE 8-7/8" 6-5/8" 6-1/2" 9-1/4" 14 TOOTH 8SP SPIKE 10 TOOTH 8SP SPIKE BAR ASSEMBLY BAR ASSEMBLY 105”/105” DOUBLE 75”/75” DOUBLE FLAT REEL ASSEMBLY FLAT REEL ASSEMBLY Figure 2-20: 2RS DBL Flat Reel Placement 9430FH -30’ LH 2-22 F-1136-2501...
  • Page 37 9TH HOLE 9TH HOLE 6-1/2" 6-5/8" 8-7/8" 9-1/4" 11 TOOTH 8SP SPIKE 14 TOOTH 8SP SPIKE BAR ASSEMBLY BAR ASSEMBLY 75”/75” DOUBLE 105”/105” DOUBLE FLAT REEL ASSEMBLY FLAT REEL ASSEMBLY Figure 2-21: 2RS DBL Flat Reel Placement 9430FH -30’ RH 2-23...
  • Page 38 10TH HOLE 6" 12-3/8" 14-1/8" 12-3/4" 14 TOOTH 8SP SPIKE 10 TOOTH 8SP SPIKE BAR ASSEMBLY BAR ASSEMBLY 105”/105” DOUBLE 75”/75” DOUBLE FLAT REEL ASSEMBLY FLAT REEL ASSEMBLY Figure 2-22: 2RS DBL Flat Reel Placement 9430FH -32’ LH 2-24 F-1136-2501...
  • Page 39 12TH HOLE 6TH HOLE 14" 14-1/8" 12-1/4" 6" 12 TOOTH 8SP SPIKE 14 TOOTH 8SP SPIKE BAR ASSEMBLY BAR ASSEMBLY 90”/90” DOUBLE 105”/105” DOUBLE FLAT REEL ASSEMBLY FLAT REEL ASSEMBLY Figure 2-23: 2RS DBL Flat Reel Placement 9430FH -32’ RH 2-25...
  • Page 40 7TH HOLE 8-3/4" 6-5/8" 13-7/8" 6-1/2" 16 TOOTH 8SP SPIKE 10 TOOTH 8SP SPIKE BAR ASSEMBLY BAR ASSEMBLY 120”/120” DOUBLE 75”/75” DOUBLE FLAT REEL ASSEMBLY FLAT REEL ASSEMBLY Figure 2-24: 2RS DBL Flat Reel Placement 9430FH -34’ LH 2-26 F-1136-2501...
  • Page 41 32ND HOLE 12TH HOLE 6-3/8" 6-3/4" 8-7/8" 13-1/2" 11 TOOTH 8SP SPIKE 16 TOOTH 8SP SPIKE BAR ASSEMBLY BAR ASSEMBLY 75”/75” DOUBLE 120”/120” DOUBLE FLAT REEL ASSEMBLY FLAT REEL ASSEMBLY Figure 2-25: 2RS DBL Flat Reel Placement 9430FH -34’ RH 2-27...
  • Page 42 Double Flat Reel Assembly 105/105 75/75 Denotes Use Of Bar Clamp W/Tabs (P/N 186200) NOTE: For Proper Spike Harrow Placment. Be Sure To Count Both Round And Square Spike Holes. Figure 2-26: 3RS DBL Flat Reel Placement 9430FH -30’ LH 2-28 F-1136-2501...
  • Page 43 Double Flat Reel Assembly 75/75 105/105 Denotes Use Of Bar Clamp W/Tabs (P/N 186200) NOTE: For Proper Spike Harrow Placment. Be Sure To Count Both Round And Square Spike Holes. Figure 2-27: 3RS DBL Flat Reel Placement 9430FH -30’ RH 2-29...
  • Page 44 Double Flat Reel Assembly 105/105 75/75 Denotes Use Of Bar Clamp W/Tabs (P/N 186200) NOTE: For Proper Spike Harrow Placment. Be Sure To Count Both Round And Square Spike Holes. Figure 2-28: 3RS DBL Flat Reel Placement 9430FH -32’ LH 2-30 F-1136-2501...
  • Page 45 Double Flat Reel Assembly 90/90 105/105 Denotes Use Of Bar Clamp W/Tabs (P/N 186200) NOTE: For Proper Spike Harrow Placment. Be Sure To Count Both Round And Square Spike Holes. Figure 2-29: 3RS DBL Flat Reel Placement 9430FH -32’ RH 2-31...
  • Page 46 Double Flat Reel Assembly 120/120 75/75 Denotes Use Of Bar Clamp W/Tabs (P/N 186200) NOTE: For Proper Spike Harrow Placment. Be Sure To Count Both Round And Square Spike Holes. Figure 2-30: 3RS DBL Flat Reel Placement 9430FH -34’ LH 2-32 F-1136-2501...
  • Page 47 Double Flat Reel Assembly 75/75 120/120 Denotes Use Of Bar Clamp W/Tabs (P/N 186200) NOTE: For Proper Spike Harrow Placment. Be Sure To Count Both Round And Square Spike Holes. Figure 2-31: 3RS DBL Flat Reel Placement 9430FH -34’ RH 2-33...
  • Page 48 TABLE OF CONTENTS Table provided for general use. NOTES: 2-34 F-1136-2501...
  • Page 49 Chapter 3 TABLE OF CONTENTS Assembly Instructions It is very important that your new 9430FH Field Cultivator WARNING be properly assembled, adjusted and lubricated before use. Illustrations in this section show proper assembly Do not attempt to lift heavy parts (such as the procedures.

  • Page 50: Center Frame Assembly

    TABLE OF CONTENTS Center Frame Assembly 10. Attach the bottom end of the cylinder lift arms to the outer side of bearing housing mounts with 1 x 2-3/4 bolts and 1 lock nuts. IMPORTANT 11. Connect the top end of the cylinder lift arms to the Read all safety precautions at the front of the section radius rod and hose mounts with 1 x 4 bolts and lock before attempting any of the following procedures.
  • Page 51 TABLE OF CONTENTS HOSE MOUNT, CENTER FRAME 1 X 4 BOLT, ASSEMBLY RH 1 LOCK NUT 1-1/4 X 2-3/4 RADIUS ROD STEP PIN, HOSE CLAMP, ASSEMBLY 1/2 X 2-1/4 3/8 X 2-3/4 BOLT, SPRING CLAMP, SPRING PIN, 3/8 LOCK NUT TINE CLAMP, 1 LOCK NUT 5/8 X 5-1/2 BOLT,...
  • Page 52 TABLE OF CONTENTS Center Frame Fold, Hitch Exten- 4. Align holes of the depth valve with plunger to front of machine to holes of bracket on the frame extension. sion, Depth Control Assembly Use the depth valve mounting holes closet to the plunger when mounting.
  • Page 53 TABLE OF CONTENTS 5/8 X 3-11/16 X 5-1/2 5/8 X 3-11/16 X 5-1/2 WING STABILIZER REAR FOLD U-BOLT, U-BOLT, 5/8 LOCK NUT ASSEMBLY CYLINDER MOUNT 5/8 LOCK NUT DEPTH STOP TUBE ASSEMBLY, 5/8 X 2-1/2 BOLT, FRONT FOLD CYLINDER 5/8 LOCK NUT MOUNT, 5/8 X 3-11/16 X 5-1/2 U-BOLT, 5/8 LOCK NUT CENTER FRAME...

  • Page 54: Hitch Assembly

    TABLE OF CONTENTS Hitch Assembly Gauge Wheel Assembly Center 1. Remove the 1 x 7-1/2 bolt and 1 lock nut from the IMPORTANT gauge wheel extension mount assembly Figure 3-4. Read all safety precautions at the front of the section before attempting any of the following procedures.
  • Page 55 TABLE OF CONTENTS WING NUT HOSE HOLDER CLAMP 1/4-20 X 1 HEX BOLT 3/8-16 HOSE HOLDER BRACKET HEX NUT 3/4-10 FLANGE NUT STOR-A-WAY HARNESS 3/4-10 X 7 3/8-16 X 3-1/2 HEX BOLT ALL THREAD 1/4-20 LOCK NUT DETAIL A 21” HITCH EXTENSION GAUGE WHEEL ASSEMBLY...

  • Page 56: Wing Frames

    TABLE OF CONTENTS Wing Frames Wing Gauge Wheel Installation 1. Attach wing frame assemblies to center frame using 1. Remove the 1 x 7-1/2 bolt and 1 lock nut from the flat washers, 1-1/4 x 6-1/8 pin and 5/16 x 2-1/2 spring gauge wheel extension mount assembly slotted pins See Figure...
  • Page 57 TABLE OF CONTENTS SPRING CLAMP ASSEMBLY 1-1/4 X 6-1/8 PINS, WING FLAT WASHERS, ASSEMBLY 5/16 X 2-1/2 SPRING STAND SLOTTED PINS 21” RADIUS ROD ASSEMBLY 6-BOLT TIRE/WHEEL 1 X 7-1/2 BOLT GAUGE WHEEL ASSEMBLY, & 1 LOCK NUT EXTENSION MOUNT 9/16 LUG NUTS 3/4 X 5-1/2 BOLTS 1 X 7-1/2 BOLT...
  • Page 58 Landoll to assign new part numbers for the cylinders and corresponding service items, i.e. packing kits, glands, clevis ends, etc. During assembly and service of your Landoll equipment it is important to know which cylinders you are dealing with. During the modification process listed above, Landoll...
  • Page 59 TABLE OF CONTENTS Cross Reference Matrix For Model 9430FH FC Old Landoll Part Number New Landoll Part Number Landoll Part Description 140471 247546 Cylinder, 3-3/4 x 10, Rephase 140470 247547 Cylinder, 4 x 10, Rephase 3-11...

  • Page 60: Hydraulic Installation

    TABLE OF CONTENTS Hydraulic Installation 7. Attach hose mounts to lift tower assemblies with 1 x 4 screws and 1 lock nuts See Figure 3-6. See Figures 3-11 through 3-15 for hydraulic cylinder fittings (factory installed and those installed during NOTE setup.) 2 hose mounts used on center frame...
  • Page 61 TABLE OF CONTENTS 9. Install lift system hoses per Figure 3-11. Wrap lift system hoses with blue hose wrap. NOTE Use side port for all base end lift cylinder connections. 10. Install fold system hoses per Figure 3-15. Wrap fold system hoses with yellow hose wrap.
  • Page 62 TABLE OF CONTENTS CLEVIS & ROLL PINS PROVIDED W/CYLINDER 4-1/2 X 30 CYLINDER FOLD & ROLL PINS, 1-1/4N FLAT WASHERS Figure 3-10: Fold Cylinder Installation 3-14 F-1136-2501...
  • Page 63 HOSE CYLINDER 3/4-16 MALE COUPLER BLUE HOSE WRAP 90° #8 ADAPTER FRONT OF 16 PORT MACHINE MANIFOLD #8 TO #8 16 PORT ADAPTER LIFT/FOLD MANIFOLD ASSEMBLY 45° #8 DETAIL A ADAPTER 3/4-16 PLUG Figure 3-11: Hydraulic Lift Installation 9430FH 3-15...
  • Page 64 NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: INSERT CLAMP NOTE: RUN HOSES THROUGH BOLT POINTING AWAY ALL HOSE CLAMPS, LOOPS, HOSE MOUNTS FROM TIRE AND HOLE OF BEARING CAP WELDMENTS Figure 3-12: Hydraulic Lift Layout 9430FH LH 3-16 F-1136-2501...
  • Page 65 TABLE OF CONTENTS NOTE: INSERT CLAMP NOTE: RUN HOSES THROUGH BOLT POINTING AWAY ALL HOSE CLAMPS, LOOPS, HOSE MOUNTS FROM TIRE AND HOLE OF BEARING CAP WELDMENTS Figure 3-13: Hydraulic Lift Layout 9430FH RH 3-17...
  • Page 66 90° #8 ADAPTER 16 PORT MANIFOLD #8 TO #8 #8 TO #8 16 PORT ADAPTER ADAPTER LIFT/FOLD MANIFOLD ASSEMBLY 8 PORT FOLD MANIFOLD 8 PORT 3/4-16 PLUG ASSEMBLY MANIFOLD DETAIL B DETAIL A Figure 3-14: Hydraulic Fold Installation 9430FH 3-18 F-1136-2501...
  • Page 67 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-15: Hydraulic Fold Layout 9430FH 3-19...
  • Page 68 TABLE OF CONTENTS Table provided for general use. NOTES: 3-20 F-1136-2501...
  • Page 69 TABLE OF CONTENTS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND WHITE – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) MAIN WARNING LIGHT HARNESS - WIRING CHART (NOTE: The Color Of The Wire Jacket Does Nor Necessarily Match The Color Of The 7 Pin Connector) RIGHT...
  • Page 70 See Figures 3-17 Detail A. 6. Attach the amber light assemblies to the center 12. install the Landoll decal to the rear of the cylinder frame using 1/2 x 2-1/4 u-bolts and lock nuts. The mount rear. amber reflectors should point forward on both 13.
  • Page 71 SIS 20 MPH DECAL, SMV EMBLEM 1/4 X 1 BOLTS, LOCK NUTS 1/4 X 1-1/2 BOLTS & LOCK NUT DETAIL A RED AG CYLINDER LANDOLL LAMP MOUNT DECAL REAR REFLECTOR ASSEMBLY, INCLUDES MOUNT, SMV MOUNTING RED & ORANGE REFLECTOR BRACKET, 5/8 X 2-1/2...
  • Page 72 TABLE OF CONTENTS NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE CLAMPS ALONG HYDRAULIC HOSES NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE LOOPS ALONG HYDRAULIC NOTE: SECURE HOSES LIGHT HARNESSES WITH TIES STRAPS TO KEEP CLEAR OF ANY MOVING PARTS NOTE: RUN LIGHT HARNESS THROUGH HOSE CLAMPS...
  • Page 73 TABLE OF CONTENTS Table provided for general use. NOTES: 3-25...

  • Page 74: Tine Installation

    TABLE OF CONTENTS Tine Installation See Figure 2-6 through for tine placement dimensions. Verify that all tine clamps and spring clamps are properly installed. 1. Slide stems through slotted hole of the spring clamp See Figure 3-19. Secure with 5/8 x 1-3/4 bolt and 5/8 flange lock nut.
  • Page 75 TABLE OF CONTENTS 5/8 X 5-1/2 BOLT, 5/8 FLANGE LOCK NUT CLAMP TINE 5/8 X 1-3/4 BOLT, 5/8 FLANGE LOCK NUT SPRING CLAMP STEM TINE SHANK SPACER 2-3/4 DANISH SWEEP, 7/16 X 1-3/4 PLOW BOLT, 7/16 FLANGE NUT Figure 3-19: Shank Installation 3-27...

  • Page 76: Row Coil Tine And Reel Harrow Installation

    TABLE OF CONTENTS 3 Row Coil Tine and Reel Harrow 4. Attach reel assemblies or flat reel assemblies to the reel arm assemblies using 5/8 x 3-11/16 x 4-5/8 Installation u-bolts and 5/8 lock nuts. 5. Attach flat bar reels with angled blades as shown See Figures 2-8 through 2-13...
  • Page 77 TABLE OF CONTENTS 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT TINE & REEL ASSEMBLY 3/4 X 5-1/2 BOLT, 3/4 LOCK NUT NOTE: REMOVE STOP BOLTS AND ROTATE DOWN WITH STOP BOLTS ABOVE TINES DETAIL A NOTE: FRONT ROW TINE SHIPPING POSTION DETAIL A...

  • Page 78: Row Spike And Reel Harrow Installation

    1. Attach the 3 RSD w/spring and 3 RSD w/o spring 4. Attach spike bars to spike harrow arm assemblies per (Models 9430FH -32’-34’ only) arm assemblies to placement drawings using bar clamps, bar clamp the rear tube of the center and wing frames using...
  • Page 79 TABLE OF CONTENTS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 3 RSD ARM ASSEMBLY W/O SPRING 3 RSD ARM 3 RSD ARM ASSEMBLY ASSEMBLY W/SPRING W/SPRING 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT 3/4 X 5-1/2 BOLT, 3/4 LOCK NUT HARROW BAR MOUNT W/TABS...
  • Page 80 TABLE OF CONTENTS 2RS DBL Flat Reel Installation 2. Refer to Note: spike bar alignment See Figures 3-26 for proper alignment of spike bar assemblies. Be sure See Figures 2-20 2-25 for 2 row spike and double flat they are aligned properly on both right and left side of reel placement dimensions of spike harrow arms, spike each section.
  • Page 81 TABLE OF CONTENTS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT 3 RSD ARM ASSEMBLY W/SPRING 1/2 X 3 BOLT DOUBLE FLAT BAR CLAMP REEL ASSEMBLY PLATE SPIKE BAR CLAMP 3 X 3 TUBE CLAMPS, PLATE...
  • Page 82 TABLE OF CONTENTS 3RS DBL Flat Reel Installation 2. Refer to spike bar alignment See Figure 3-26 proper alignment of spike bar assemblies. Be sure See Figure 2-26 2-31 for 3 RS and double flat reel they are aligned properly on both right and left side of placement dimensions of spike harrow arms, spike bars, each section.
  • Page 83 TABLE OF CONTENTS NOTE: Spike Bar Alignment Right Side Shown 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3RS & DBL REEL 3/4 LOCK NUT ARM ASSEMBLY SPIKE BAR 1/2 X 3 BOLT DOUBLE FLAT BAR CLAMP REEL ASSEMBLY PLATE CLAMP PLATE...

  • Page 84: Rear Tow Hitch (Option)

    TABLE OF CONTENTS Rear Tow Hitch (Option) 7. Attach the front of the tow hitch assembly to the cultivator frame cross tubes using 5/8 x 3-11/16 x 1. Unfold and lower the field cultivator to the ground. 5-1/2 u-bolts, 5/8 x 6 hex bolts and 5/8 lock nuts. 2.
  • Page 85 TABLE OF CONTENTS WEIGHT TIE-STRAP HITCH PLATE NOTE: ROUTE HOSES ALONG OTHER HOSES, THROUGH HOSE CLAMPS, ALONG CENTER FRAME, AND HITCH TO FRONT OF MACHINE FRONT FRONT WEIGHT HOSE CLAMP LOCK PLATE 3/4 X 4-1/2 3/8 X 2-3/4 HEX BOLT & HEX BOLT &...
  • Page 86 TABLE OF CONTENTS 26” 26” NOTE: LOCATION OF 12” SHANK EXTENSION RIGHT REAR TANDEM LIGHT USED WITH REAR TOW HITCH TAIL LIGHT MOUNT HARNESS NOTE: CENTER LIGHTING MODULE REAR TOW HITCH ON CENTER FRAME MAIN WIRING HARNESS NOTE: ROUTING OF REAR TOW TANDEM LIGHT HARNESS HITCH ASSEMBLY...

  • Page 87: Operation

    Chapter 4 TABLE OF CONTENTS Operation DANGER DANGER DANGER DANGER Never allow anyone to ride on the 9430FHField When transporting the unit, place cylinder Cultivator at any time. Allowing a person to ride lockouts in the transport lock position after fully on the machine can inflict serious personal injury extending the cylinders.

  • Page 88: Hydraulic Lift System

    TABLE OF CONTENTS Hydraulic Lift System 1. The rephasing hydraulic lift system contains smaller wing frame cylinders plumbed in series with larger The Field Cultivator is equipped with a rephasing center frame cylinders. It is important that the hydraulic lift system to raise and lower the unit in the field. cylinders be connected in the proper series for the lift system to operate correctly.
  • Page 89 TABLE OF CONTENTS Table provided for general use. NOTES:...

  • Page 90: Hydraulic Fold System

    TABLE OF CONTENTS Hydraulic Fold System 3. The hydraulic fold system is equipped with restrictors in the cylinders to prevent uncontrolled falling of wing The Field Cultivator is equipped with a hydraulic fold frames when folding/unfolding. Removal or improper system to raise and lower the wing frames for narrow assembly of these restrictors can cause the machine transport.
  • Page 91 TABLE OF CONTENTS NOTE: BOTH SIDES ARE EITHER FOLDED OR UNFOLDED DEPENDENT ON OPERATION DETAIL A DETAIL B TRANSPORT LOCK PIN STORAGE LOCATION WHEN FOLDED DETAIL B WING STABILIZER BRACKET MOUNT DETAIL A WING STABILIZER BRACKET MOUNT TRANSPORT LOCK PIN STORAGE LOCATION WHEN UNFOLDED Figure 4-4: Wing Stabilizer Bracket Locks...
  • Page 92 TABLE OF CONTENTS Transporting 3. When towing in combination, the maximum equipment ground speed shall be limited to the 1. Check and follow all federal, state, and local lowest specified ground speed of any of the towed requirements before transporting the Field Cultivator. implements.

  • Page 93: Tractor Preparation

    6. Check that tires are of proper size, load rating, and inflated to manufacture specifications before The Landoll 9430FH Field Cultivator is designed to be transporting. Check wheel lug bolts to insure pulled by tractor equipped with a double lip or clevis type tightness.

  • Page 94: Leveling (Side To Side)

    TABLE OF CONTENTS Leveling (Side to Side) 3. To adjust the radius rod’s, loosen the 1-3/4” locking nut against the radius rod tube. Adjust the screw 1. Leveling the Field Cultivator side-to-side involves adjustment in or out to the desired setting. An leveling the center frame then leveling the wing adjusting wrench is provided to make this frames to the center frame.
  • Page 95 TABLE OF CONTENTS 9430FH Gauge Wheels NOTE Initially the front radius rods are set to 21”on center 1. The front gauge wheels of the floating hitch cultivator before final adjustment raise and lower with center and wing lift wheels See Figure 4-7...

  • Page 96: Depth Stop Adjustment

    TABLE OF CONTENTS Depth Stop Adjustment LED Light Operation 1. The operating depth of the Field Cultivator is 1. Attach the seven-pin plug to the socket at the rear of controlled by a single-point depth stop. The stop is the tractor. The socket must be in good working located at the center front of the machine order, and free of dirt, grease, and corrosion.

  • Page 97: General Operation

    TABLE OF CONTENTS 9400 Danish Tine Shank 1. The 9400 series field cultivator uses a two-piece are 40mm (1.57”) centers and accepts 12mm (7/16”) Danish-tine shank assembly. Shanks are spaced on mounting bolts. 4” centers, on a split-the-middle pattern. The shanks Install the lower stem through hole in the rear of the are configured on a true 6-row pattern for greater spring clamp.

  • Page 98: Row Coil Tine And Reel Adjustments

    TABLE OF CONTENTS 3 Row Coil Tine and Reel Adjust- 4. Each coil tine harrow may be adjusted for spring pressure as well See Figure 4-10. Raise the tine ments harrow off the ground. Adjust the spring pressure the same for both harrow arms on each section. Remove 1.
  • Page 99 TABLE OF CONTENTS SPRING TINE ANGLE ASSEMBLY MORE LESS 1-8 HEX NUTS AGGRESSIVE AGGRESSIVE 1/2” 21-3/4” REEL TINE SPRING ASSEMBLY PRESSURE HEAVY CLEVIS PIN HARROW LIGHT ADJUSTMENT PIN CLEVIS PIN HARROW ADJUSTMENT PIN REEL 3 ROW COIL TINE ASSEMBLY ASSEMBLY HARROW ADJUSTMENT HOLES Figure 4-10: 3 Row Coil Tine and Reel Adjustments...

  • Page 100: Row Spike And Reel Adjustments

    TABLE OF CONTENTS 3 Row Spike and Reel Adjust- 5. The 12” diameter reel consists of nine 3/4” diameter round bars with a chevron shape for smoother ments rotation. The reels have no inner shaft to reduce plugging in wetter conditions. The reels operate 1.
  • Page 101 TABLE OF CONTENTS LEAST TOOTH ANGLE MIDDLE TOOTH ANGLE SPRING SPRING CARRYING CHAIN MOST TOOTH ANGLE ASSEMBLY ASSEMBLY 1-8 HEX NUTS 21-3/4” REEL ASSEMBLY FORWARD PULL CHAIN HARROW ADJUSTMENT PIN BAR CLAMP BAR CLAMP W/TABS SPIKE BAR ASSEMBLY CLEVIS PIN REEL ASSEMBLY Figure 4-11: 3 Row Spike and Reel Adjustments...
  • Page 102 TABLE OF CONTENTS 2RS DBL Flat Reel Adjustments • For the most aggressive spike tooth action, install the harrow adjustment pin in the forward mounting hole over each bar clamp for each spike bar The optional 2 row spike and reel attachment consists of Figure 4-12.
  • Page 103 TABLE OF CONTENTS LEAST TOOTH ANGLE SPRING SPRING MIDDLE TOOTH ANGLE ASSEMBLY ASSEMBLY CARRYING CHAIN MOST TOOTH ANGLE 1-8 HEX NUTS 21” REEL FORWARD ASSEMBLY PULL CHAIN HARROW ADJUSTMENT PIN BAR CLAMP W/TABS SPIKE BAR DOUBLE FLAT ASSEMBLY REEL ASSEMBLY CLEVIS PIN Figure 4-12: 2RS DBL Flat Reel Adjustments 4-17...
  • Page 104 TABLE OF CONTENTS 3 RS Double Flat Reel • For the most aggressive spike tooth action, install the harrow adjustment pin in the forward mounting hole Adjustments over each bar clamp for each spike bar Figure 4-14. This will position the spike teeth to be in The optional 3 RS double flat reel attachment consists of the most vertical position.
  • Page 105 TABLE OF CONTENTS To adjust the reel height: NOTICE • Loosen the locking hex nut against the threaded spring end. • Setting the reels too low may cause the reels to • Raise or lower the reel by turning the head of the plug or push dirt.
  • Page 106 TABLE OF CONTENTS Tooth Angle, Tooth Angle, Tooth Angle, Least Middle Most Spring Assembly Carrying Chain 1 Nuts Double Flat Reel Assembly 3/4” 21” Forward Pull Chain Harrow Adjustment Pin Double Flat Forward Reel Assembly Pull Chain Bar Clamp Spike Bar Assembly Harrow Adjustment Pin...

  • Page 107: Maintenance And Lubrication

    TABLE OF CONTENTS Chapter 5 Maintenance and Lubrication Wheel Bearing Maintenance – Wheel Bearing Maintenance -- Non Triple-Lip Triple-Lip Wheel bearing maintenance should be performed at the Transport tires use a self-contained seal with multiple beginning of every season of use. Check the wheel lips.
  • Page 108 TABLE OF CONTENTS Lubrication fittings before greasing. Replace any lost or broken fittings immediately. 1. A proper maintenance schedule will insure a long 3. Wheel seals, when properly installed, will allow operating life and peak performance. Performing the grease to pass without harm to seals. Regular following lubrication will ensure maximum operating lubrication will extend service life, particularly in life of the Field Cultivator...
  • Page 109 TABLE OF CONTENTS Storage 1. The service life of the Field Cultivator will be extended by proper off-season storage practices. Prior to storing the unit, complete the following procedures: a. Completely clean the unit. b. Inspect the machine for worn or defective parts. Replace as needed.
  • Page 110 TABLE OF CONTENTS Table provided for general use. NOTES: F-1136-2501...

  • Page 111: Troubleshooting Guide

    Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 9430FH Field Cultivator. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM...
  • Page 112 TABLE OF CONTENTS PROBLEM PROBABLE CAUSE SOLUTION WINGS FOLD TOO FAST Restrictors not properly installed in Black restrictor fittings should be in both cylinders ends of outer fold cylinders and rod end of inner fold cylinders. HYDRAULIC - LIFT CYLINDERS NOT Lift cylinders not in phase.
  • Page 113 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 10/07/2022 F-1136 New Manual 01/10/2023 F-1136-0123 Initial Release 01/27/2025 F-1136-2501 Prince cylinder update. added 3RS DBL flat reel attachment...
  • Page 114 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 9430FH Field Cultivator Operator’s Manual Re-Order Part Number F-1136 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...

Table of Contents