Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Tiller
  5. 9450FH
  6. Operator's manual

Landoll 9450FH Operator's Manual

Field cultivator
Hide thumbs

Advertisement

Quick Links

Download this manual
'
Model 9450FH
Field Cultivator
Operators Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
F-1139-0123

Advertisement

loading
Need help?

Need help?

Do you have a question about the 9450FH and is the answer not in the manual?

Questions and answers

Related Manuals for Landoll 9450FH

Summary of Contents for Landoll 9450FH

  • Page 1 ‘ Model 9450FH Field Cultivator Operators Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-1139-0123...
  • Page 2 The identification plate, which lists the model number and serial number, is located on the front of the frame. SERIAL NUMBER The serial number is located on the identification plate. The Following information will help decode the 9450FH Field Cultivator serial number 94H222000 = xxmyysssss QR CODE DECAL...
  • Page 3 DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
  • Page 5 9450FH Gauge Wheels ........
  • Page 6 TABLE OF CONTENTS Depth Stop Adjustment ........4-10 LED Light Operation.
  • Page 7 Introduction and Safety Information The Landoll Model 9450FH Field Cultivator is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation.
  • Page 8 5. Use a locking-style hitch pin that properly fits the The safety statements contained in this manual relate to tractor drawbar and the implement hitch. Lock the the operation of the Model 9450FH Field Cultivator. tractor drawbar in the center position to prevent loss of steering control.
  • Page 9 TABLE OF CONTENTS High Pressure Fluid Safety 6. Attach the safety chain to the tractor recommended drawbar support. Provide only enough slack in the 1. Escaping fluid under pressure can be nearly invisible chain for turning. Do not attach the safety chain to an and have enough force to penetrate the skin causing intermediate support.
  • Page 10 TABLE OF CONTENTS Tire Safety Safety Chain 1. Tire changing can be dangerous and should be 1. Use a chain with a strength rating equal to or greater performed by trained personnel using correct tools than the gross weight of towed machinery, which is and equipment.
  • Page 11 Safety Decals and Reflectors New safety signs may be ordered from your Landoll dealer. Refer to this section for parts and proper safety The 9450FH Field Cultivator is equipped with all safety sign placement. signs installed for safe operation. To Install new safety signs: For you safety: 1.
  • Page 12 TABLE OF CONTENTS P/N 144193 SIS 20MPH Front of center frame extension, middle QTY. 1 P/N 2-573-010037 Danger: Folding wing Front side, front hinge plate, center frame extension, both sides QTY. 2 P/N 2-573-010037 Danger: Folding wing Back side, rear hinge plate, center frame, both sides QTY.
  • Page 13 TABLE OF CONTENTS P/N 528934 Yellow Reflector Left front, amber light bracket, both sides QTY. 2 P/N 528934 Yellow Reflector Left rear, center lift plate, both sides QTY. 2 P/N 528938 Orange Reflector Back side, light brackets, top, both sides QTY.
  • Page 14 TABLE OF CONTENTS P/N 224589 SIS 20 mile/h Back side of SIS 20MPH mount plate QTY. 1 P/N 70260977 SMV Emblem Back side, SMV mount plate QTY. 1 P/N 231488 Caution: Maximum Hitch Weight Back side of rear tow hitch QTY.
  • Page 15 10 days of purchase or lease, in so as to be able to follow the suggestions made. Please order to be on file at Landoll and eligible for Warranty. take time to understand the proper maintenance schedule and SAFE operation of your equipment.
  • Page 16 1) subjected to or operated in a manner which, at any time, have exceeded the product design limits: 2) repaired or altered outside our factory in any way so as, in the judgment of Landoll Company, LLC , to affect its stability or reliability: 3) subject to misuse, negligence, accident, or has been operated in a manner expressly prohibited in the instructions;...
  • Page 17 This exclusive remedy shall not be deemed to have failed of its essential purpose so long as Landoll Company, LLC is willing and able to repair or replace defective parts in the prescribed manner.
  • Page 18 TABLE OF CONTENTS General Torque Specifications (rev. 4/97) TORQUE SPECIFIED IN FOOT POUNDS This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and cap-screws assembled without supplemental lubrication (as received condition).
  • Page 19 TABLE OF CONTENTS Hydraulic Fitting Torque Specifications TORQUE IS SPECIFIED IN FOOT POUNDS- 37 JIC, ORS, & ORB (REV. 10/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition).
  • Page 20 TABLE OF CONTENTS Model Specifications 9450FH Field Cultivator Model Number 9450FH-38 9450FH-42 9450FH-46 9450FH-50 Working Width 38'-6” 42'-6” 46'-6” 50'-6” Transport Width 17'-4” 17'-4” 17'-4” 17'-4” Transport Height 11'-11” 11'-11” 13'-11” 13'-11” Number of Shanks Shanks per Section 14-24-39-24-14 20-24-39-24-20...
  • Page 21 TABLE OF CONTENTS Table provided for general use. NOTES:...
  • Page 22 4" 14" 18" 2" 2" 4" 2" 20" 20" 2" 2" 42’ 8" 38’ 14" 8" 8" 8" 8" 14" 8" NOTE: LOCATION OF 235339 HYD HOSE MOUNT ON TOP OF TINE CLAMP Figure 2-2: Shank Placement 9450FH-38’-42’ LH F-1139-0123...
  • Page 23 40" 24" 24" 3-3/8" 4" 4" 16" 16" 18" 12" 12" 2" 22" 2" 10" 4" 4" 12" 12" 6" 2" 2" 4" 1-3/4" 1-3/4" 2" 2" 26" 8" 8" 14" 14" 8" 8" Figure 2-3: Shank Placement 9450FH-38’-42’ CENTER...
  • Page 24 4" 18" 2" 2" 20" 20" 2" 2" 2" 42’ 8" 38’ 8" 14" 14" 8" 8" 14" 8" 14" NOTE: LOCATION OF 235339 HYD HOSE MOUNT ON TOP OF TINE CLAMP Figure 2-4: Shank Placement 9450FH-38-42’ RH 2-10 F-1139-0123...
  • Page 25 TABLE OF CONTENTS Table provided for general use. NOTES: 2-11...
  • Page 26 2" 2" 24" 46’ 14" 8" 8" 14" 8" 8" 8" 14" 14" 8" NOTE: LOCATION OF NOTE: LOCATION OF WING SUPPORT 235339 HYD HOSE MOUNT ON TOP OF TINE CLAMP BRACKET Figure 2-5: Shank Placement 9450FH-46’-50’ LH 2-12 F-1139-0123...
  • Page 27 24" 40" 24" 3-3/8" 3-3/8" 4" 4" 16" 18" 16" 2" 10" 4" 12" 2" 22" 4" 12" 12" 4" 1-3/4" 1-3/4" 2" 2" 2" 2" 8-1/2" 8" 8" 8" 14" 14" 8" Figure 2-6: Shank Placement 9450FH-46’-50’ CENTER 2-13...
  • Page 28 2" 2" 2" 46’ 14" 14" 8" 8" 8" 14" 8" 8" 8" 14" NOTE: LOCATION OF NOTE: LOCATION OF WING SUPPORT 235339 HYD HOSE MOUNT BRACKET ON TOP OF TINE CLAMP Figure 2-7: Shank Placement 9450FH-46’-50’ RH 2-14 F-1139-0123...
  • Page 29 TABLE OF CONTENTS Table provided for general use. NOTES: 2-15...
  • Page 30 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 4 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 60” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-8: 3 Row Tine & Reel Placement 9450FH-38’ LH 2-16 F-1139-0123...
  • Page 31 NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-9: 3 Row Tine & Reel Placement 9450FH-38’ CENTER 2-17...
  • Page 32 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 3 ROW 4 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 60” REEL ASSEMBLY Figure 2-10: 3 Row Tine & Reel Placement 9450FH-38’ RH 2-18 F-1139-0123...
  • Page 33 TABLE OF CONTENTS Table provided for general use. NOTES: 2-19...
  • Page 34 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 3 ROW 5 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-11: 3 Row Tine & Reel Placement 9450FH-42’ LH 2-20 F-1139-0123...
  • Page 35 NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-12: 3 Row Tine & Reel Placement 9450FH-42’ CENTER 2-21...
  • Page 36 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-13: 3 Row Tine & Reel Placement 9450FH-42’ RH 2-22 F-1139-0123...
  • Page 37 TABLE OF CONTENTS Table provided for general use. NOTES: 2-23...
  • Page 38 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 6 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-14: 3 Row Tine & Reel Placement 9450FH-46’ LH 2-24 F-1139-0123...
  • Page 39 21-1/2” 13-1/2” 13-1/2” 21-5/8” NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 10 TINE 3 ROW HARROW ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-15: 3 Row Tine & Reel Placement 9450FH-46’ CENTER 2-25...
  • Page 40 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-16: 3 Row Tine & Reel Placement 9450FH-46’ RH 2-26 F-1139-0123...
  • Page 41 TABLE OF CONTENTS Table provided for general use. NOTES: 2-27...
  • Page 42 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-17: 3 Row Tine & Reel Placement 9450FH-50’ LH 2-28 F-1139-0123...
  • Page 43 NOTE: LOCATION OF 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 5 TINE 3 ROW 6 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-18: 3 Row Tine & Reel Placement 9450FH-50’ CENTER 2-29...
  • Page 44 1/2” X 4-1/2” HEX BOLTS ON FRONT GANG BARS ONLY 7 TINE 3 ROW 7 TINE 3 ROW HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-19: 3 Row Tine & Reel Placement 9450FH-50’ RH 2-30 F-1139-0123...
  • Page 45 TABLE OF CONTENTS Table provided for general use. NOTES: 2-31...
  • Page 46 11TH HOLE 13-7/8” 13-7/8” 11-3/4” 10” CATCH TRAY HOOK CATCH TRAY 7 TOOTH SPIKE 11 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 60” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-20: 3 Row Spike and Reel Harrow Placement 9450FH-38’ LH 2-32 F-1139-0123...
  • Page 47 7TH HOLE 10TH HOLE 6TH HOLE 11TH HOLE 12-7/8” 11-3/4” 12-7/8” 11-3/4” 9 TOOTH SPIKE 9 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-21: 3 Row Spike and Reel Harrow Placement 9450FH-38’ CENTER 2-33...
  • Page 48 7TH HOLE 11-3/4” 10” 13-7/8” 13-7/8” CATCH TRAY CATCH TRAY HOOK 11 TOOTH SPIKE 7 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 60” REEL ASSEMBLY Figure 2-22: 3 Row Spike and Reel Harrow Placement 9450FH-38’ RH 2-34 F-1139-0123...
  • Page 49 TABLE OF CONTENTS Table provided for general use. NOTES: 2-35...
  • Page 50 9TH HOLE 21-7/16” 6-5/16” 5-3/16” 18-5/16” CATCH TRAY HOOK CATCH TRAY 10 TOOTH SPIKE 10 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-23: 3 Row Spike and Reel Harrow Placement 9450FH-42’ LH 2-36 F-1139-0123...
  • Page 51 4H HOLE 13TH HOLE 9TH HOLE 9TH HOLE 10-9/16” 19-3/16” 6-5/16” 19-3/16” 9 TOOTH SPIKE 10 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-24: 3 Row Spike and Reel Harrow Placement 9450FH-42’ CENTER 2-37...
  • Page 52 10TH HOLE 5-3/16” 18-5/16” 6-5/16” 21-7/16” CATCH TRAY CATCH TRAY HOOK 10 TOOTH SPIKE 10 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-25: 3 Row Spike and Reel Harrow Placement 9450FH-42’ RH 2-38 F-1139-0123...
  • Page 53 TABLE OF CONTENTS Table provided for general use. NOTES: 2-39...
  • Page 54 16-5/8” 18-3/8” 14-7/8” 13-1/2” W/O SPRING CATCH TRAY HOOK CATCH TRAY 10 TOOTH SPIKE 13 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-26: 3 Row Spike and Reel Harrow Placement 9450FH-46’ LH 2-40 F-1139-0123...
  • Page 55 6TH HOLE 11TH HOLE 7TH HOLE 10TH HOLE 11-3/4” 12-7/8” 12-7/8” 11-3/4” 9 TOOTH SPIKE 9 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 75” REEL ASSEMBLY Figure 2-27: 3 Row Spike and Reel Harrow Placement 9450FH-46’ CENTER 2-41...
  • Page 56 12TH HOLE 13-1/2” 14-7/8” 18-3/8” 16-5/8” CATCH TRAY CATCH TRAY HOOK 13 TOOTH SPIKE 10 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-28: 3 Row Spike and Reel Harrow Placement 9450FH-46’ RH 2-42 F-1139-0123...
  • Page 57 TABLE OF CONTENTS Table provided for general use. NOTES: 2-43...
  • Page 58 18-1/2” 11-3/4” 12-3/8” 5-1/8” CATCH TRAY HOOK CATCH TRAY W/O SPRING 12 TOOTH SPIKE 13 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-29: 3 Row Spike and Reel Harrow Placement 9450FH-50’ LH 2-44 F-1139-0123...
  • Page 59 9TH HOLE 9TH HOLE 4TH HOLE 13TH HOLE 19-3/8” 6-1/4” 10-1/2” 19-1/4” 9 TOOTH SPIKE 10 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75” REEL ASSEMBLY 90” REEL ASSEMBLY Figure 2-30: 3 Row Spike and Reel Harrow Placement 9450FH-50’ CENTER 2-45...
  • Page 60 5-1/8” 12-3/8” 11-3/4” 18-1/2” CATCH TRAY CATCH TRAY HOOK W/O SPRING 13 TOOTH SPIKE 12 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105” REEL ASSEMBLY 105” REEL ASSEMBLY Figure 2-31: 3 Row Spike and Reel Harrow Placement 9450FH-50’ RH 2-46 F-1139-0123...
  • Page 61 TABLE OF CONTENTS Table provided for general use. NOTES: 2-47...
  • Page 62 6TH HOLE 12-1/4" 8-7/8" 7-1/2" 6-7/8" CATCH TRAY HOOK CATCH TRAY 8 TOOTH SPIKE 12 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 60”/60” FLAT REEL ASSEMBLY 90”/90” FLAT REEL ASSEMBLY Figure 2-32: 2RS DBL Flat Reel Placement 9450FH-38’ LH 2-48 F-1139-0123...
  • Page 63 10TH HOLE 10TH HOLE 5TH HOLE 11TH HOLE 8TH HOLE 6-5/8" 6-1/2" 6-1/2" 6-5/8" 10 TOOTH SPIKE 11 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75”/75” FLAT REEL ASSEMBLY 75”/75” REEL ASSEMBLY Figure 2-33: 2RS DBL Flat Reel Placement 9450FH-38’ CENTER 2-49...
  • Page 64 10TH HOLE 8TH HOLE 6-7/8" 7-1/2" 8-7/8" 12-1/4" CATCH TRAY CATCH TRAY HOOK 12 TOOTH SPIKE 8 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90”/’90” REEL ASSEMBLY 60”/60” REEL ASSEMBLY Figure 2-34: 2RS DBL Flat Reel Placement 9450FH-38’ RH 2-50 F-1139-0123...
  • Page 65 TABLE OF CONTENTS Table provided for general use. NOTES: 2-51...
  • Page 66 6TH HOLE 6-5/16" 8-15/16" 7-11/16" 6-13/16" CATCH TRAY HOOK CATCH TRAY 10 TOOTH SPIKE 12 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75”/75” FLAT REEL ASSEMBLY 90”/90” FLAT REEL ASSEMBLY Figure 2-35: 2RS DBL Flat Reel Placement 9450FH-42’ LH 2-52 F-1139-0123...
  • Page 67 10TH HOLE 10TH HOLE 5TH HOLE 11TH HOLE 8TH HOLE 6-9/16" 6-7/16" 6-7/16" 6-9/16" 10 TOOTH SPIKE 11 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75”/75” FLAT REEL ASSEMBLY 75”/75” REEL ASSEMBLY Figure 2-36: 2RS DBL Flat Reel Placement 9450FH-42’ CENTER 2-53...
  • Page 68 10TH HOLE 6TH HOLE 6-13/16" 7-11/16" 8-15/16" 6-5/16" CATCH TRAY CATCH TRAY HOOK 12 TOOTH SPIKE 10 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90”/’90” REEL ASSEMBLY 75”/75” REEL ASSEMBLY Figure 2-37: 2RS DBL Flat Reel Reel Placement 9450FH-42’ RH 2-54 F-1139-0123...
  • Page 69 TABLE OF CONTENTS Table provided for general use. NOTES: 2-55...
  • Page 70 12-3/8 " 14-3/4 " 9-1/4" 6-7/8" CATCH TRAY HOOK CATCH TRAY 12 TOOTH SPIKE 14 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 90”/90” FLAT REEL ASSEMBLY 105”/105” FLAT REEL ASSEMBLY Figure 2-38: 2RS DBL Flat Reel Placement 9450FH-46’ LH 2-56 F-1139-0123...
  • Page 71 10TH HOLE 10TH HOLE 5TH HOLE 11TH HOLE 8TH HOLE 6-5/8" 6-1/2" 6-1/2" 6-5/8" 10 TOOTH SPIKE 11 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75”/75” FLAT REEL ASSEMBLY 75”/75” REEL ASSEMBLY Figure 2-39: 2RS DBL Flat Reel Placement 9450FH-46’ CENTER 2-57...
  • Page 72 12TH HOLE 10TH HOLE 6-7/8" 9-1/4" 14-3/4" 12-3/8" CATCH TRAY CATCH TRAY HOOK 14 TOOTH SPIKE 12 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105”/’105” REEL ASSEMBLY 90”/90” REEL ASSEMBLY Figure 2-40: 2RS DBL Flat Reel Placement 9450FH-46’ RH 2-58 F-1139-0123...
  • Page 73 TABLE OF CONTENTS Table provided for general use. NOTES: 2-59...
  • Page 74 6TH HOLE 15-1/8" 14-3/8" 9-3/8" 6-5/8" CATCH TRAY HOOK CATCH TRAY 14 TOOTH SPIKE 14 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105”/105” FLAT REEL ASSEMBLY 105”/105” FLAT REEL ASSEMBLY Figure 2-41: 2RS DBL Flat Reel Placement 9450FH-50’ LH 2-60 F-1139-0123...
  • Page 75 10TH HOLE 10TH HOLE 5TH HOLE 11TH HOLE 8TH HOLE 6-5/8" 6-3/8" 6-3/8" 6-5/8" 10 TOOTH SPIKE 11 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 75”/75” FLAT REEL ASSEMBLY 75”/75” REEL ASSEMBLY Figure 2-42: 2RS DBL Flat Reel Placement 9450FH-50’ CENTER 2-61...
  • Page 76 12TH HOLE 12TH HOLE 6-5/8" 9-3/8" 14-3/8" 15-1/8" CATCH TRAY CATCH TRAY HOOK 14 TOOTH SPIKE 14 TOOTH SPIKE HARROW ASSEMBLY HARROW ASSEMBLY 105”/’105” REEL ASSEMBLY 105”/105” REEL ASSEMBLY Figure 2-43: 2RS DBL Flat Reel Placement 9450FH-50’ RH 2-62 F-1139-0123...
  • Page 77 Chapter 3 TABLE OF CONTENTS Assembly Instructions It is very important that your new 9450FHField Cultivator WARNING be properly assembled, adjusted and lubricated before use. Illustrations in this section show proper assembly Do not attempt to lift heavy parts (such as the procedures.
  • Page 78 10. Attach the bottom end of the cylinder lift arms to the outer side of bearing housing mounts with 1 x 2-3/4 9450FH-38’, 42’, 46’ & 50’ bolts and 1 lock nuts. 11. Connect the top end of the cylinder lift arms to the...
  • Page 79 5/8 X 2 BOLT, FRAME RADIUS 5/8 LOCK NUT EXTENSION CENTER FRAME ASSEMBLY ASSEMBLY LH TRANSPORT LOCK, L-PIN, MODELS HAIRPIN CLIP 9450FH-38’-42’ UHMW LIFT/FOLD MANIFOLD BEARING 2 HOLE ASSEMBLY, SPACERS, PLATE CENTER LIFT DETAIL B 1/2 X 5 BOLTS, ASSEMBLY 1/2 FLANGE...
  • Page 80 3-3. Attach hitch extension ears to NOTE front of center frame with 1-7/16 pins, machine bushings and 5/16 x 2-1/2 spring pins. Location of rubber mount for models 9450FH-38’-42’ 2. Attach the front & rear fold cylinder mounts to the top and 9450FH-46’-50’ See Figures 3-3, Detail B.
  • Page 81 TABLE OF CONTENTS WING STABILIZER 5/8 X 3-11/16 X 5-1/2 5/8 X 3-11/16 X 5-1/2 REAR FOLD ASSEMBLY 9650FH-46’-50’ U-BOLT, U-BOLT, 5/8 LOCK NUT CYLINDER MOUNT 5/8 LOCK NUT DEPTH STOP TUBE ASSEMBLY, 5/8 X 2-1/2 BOLT, FRONT FOLD CYLINDER 5/8 LOCK NUT MOUNT, 5/8 X 3-11/16 X 5-1/2 U-BOLT, 5/8 LOCK NUT...
  • Page 82 TABLE OF CONTENTS Hitch Assembly Gauge Wheel Assembly Center 1. Remove the 1 x 7-1/2 bolt and 1 lock nut from the IMPORTANT gauge wheel extension mount assembly Figure 3-4. Read all safety precautions at the front of the section before attempting any of the following procedures.
  • Page 83 TABLE OF CONTENTS WING NUT HOSE HOLDER CLAMP 1/4-20 X 1 HEX BOLT 3/8-16 HOSE HOLDER BRACKET HEX NUT 3/4-10 FLANGE NUT STOR-A-WAY HARNESS 3/4-10 X 7 3/8-16 X 3-1/2 HEX BOLT ALL THREAD 1/4-20 LOCK NUT DETAIL A 21” HITCH EXTENSION GAUGE WHEEL ASSEMBLY...
  • Page 84 TABLE OF CONTENTS Inner Wing Frames Wing Gauge Wheel Installation 1. Attach inner wing frame assemblies to center frame 1. Remove the 1 x 7-1/2 bolt and 1 lock nut from the using flat washers, 1-1/4 x 6-1/8 pins and 5/16 x gauge wheel extension mount assembly 2-1/2 spring slotted pins See Figure...
  • Page 85 TABLE OF CONTENTS RADIUS ROD 1-1/4 X 6-1/8 PINS, ASSEMBLY FLAT WASHERS, 5/16 X 2-1/2 SPRING STAND SLOTTED PINS INNER WING 21” ASSEMBLY 6-BOLT TIRE/WHEEL 1 X 7-1/2 BOLT ASSEMBLY, & 1 LOCK NUT 9/16 LUG NUTS 3/4 X 5-1/2 BOLTS &...
  • Page 86 TABLE OF CONTENTS Outer Wing Frames NOTE 1. Install outer wing frames to inner wing frames using All tire/wheel assemblies are mounted with the valve 1-1/4-7 x 7 hex head cap screws, and hex lock nuts stem facing outward. See Figure 3-6 Note the direction of bolts as shown in Figure 3-6.
  • Page 87 TABLE OF CONTENTS 1-1/4 X 7 BOLT, 1-1/4 LOCK NUT, NO WASHERS 1-1/4 X 7 BOLT, FLAT WASHERS, RADIUS ROD 1-1/4 LOCK NUT ASSEMBLY STAND 21” INNER WING ASSEMBLY 1 X 7-1/2 BOLT & 1 LOCK NUT 6-BOLT TIRE/WHEEL ASSEMBLY, 3/4 X 5-1/2 BOLTS SPRING CLAMP 9/16 LUG NUTS...
  • Page 88 TABLE OF CONTENTS Hydraulic Installation NOTE Use side port for all base end lift cylinder See Figures 3-12 through 3-23 for hydraulic cylinder connections. fittings (factory installed and those installed during 5. Attach hose clamps to the hitch using 3/8-16 x 2-1/2 setup.) hex head cap screws and hex lock nuts.
  • Page 89 TABLE OF CONTENTS 7. Install hose mounts on both outer wings through tine 9. Install lift system hoses per Figure 3-12 (9650-38 and assembly with 5/8 x 6 screw, 5/8 flat washer and 5/8 9650-42) or Figure 3-18 (9650-46 and 9650-50.) flange lock nuts See Figure 3-8.
  • Page 90 WING EXTENSION 1-1/4N FLAT WASHERS, ROLLER & BUSHING 1-1/4-7 LOCK NUT FOLD & ROLL PINS, 1-1/4N FLAT WASHERS 4 X 16 CYL (TOP PORTS) (9450FH-38’-42’) 4 X 16 CYL (SIDE PORTS) (9450FH-46’-50’) DETAIL A Figure 3-11: Fold Cylinder Installation 3-14 F-1139-0123...
  • Page 91 1/2” X 306” #10 HEX HOSE SOCKET PLUG 3/8” X 267” 90° #8 3/4-16 MALE HOSE ADAPTER COUPLER 3-1/2 X 10 CYLINDER BLUE HOSE WRAP FRONT OF MACHINE CULTIVATOR MANIFOLD ASSEMBLY DETAIL A Figure 3-12: Hydraulic Lift Installation 9450FH-38’ - 42’ 3-15...
  • Page 92 ALL HOSE CLAMPS & LOOPS NOTE: RUN HOSES THROUGH NOTE: INSERT CLAMP ALL HOSE CLAMPS, LOOPS, HOSE MOUNTS BOLT POINTING AWAY AND HOLE OF BEARING CAP WELDMENTS FROM TIRE Figure 3-13: Hydraulic Lift Layout 9450FH-38’ - 42’ LH 3-16 F-1139-0123...
  • Page 93 TABLE OF CONTENTS NOTE: INSERT CLAMP NOTE: RUN HOSES THROUGH BOLT POINTING AWAY ALL HOSE CLAMPS, LOOPS, HOSE MOUNTS FROM TIRE AND HOLE OF BEARING CAP WELDMENTS Figure 3-14: Hydraulic Lift Layout 9450FH-38’ - 42’ RH 3-17...
  • Page 94 TABLE OF CONTENTS Table provided for general use. NOTES: 3-18 F-1139-0123...
  • Page 95 HOSE CULTIVATOR ADAPTER MANIFOLD ASSEMBLY 8 PORT 8 PORT FOLD MANIFOLD ADAPTER MANIFOLD #8 TEE DETAIL B #8 TEE ASSEMBLY ADAPTER #8 O-RING- DETAIL A FRONT OF TUBE 90° ADAPTER MACHINE Figure 3-15: Hydraulic Fold Installation 9450FH-38’ - 42’ 3-19...
  • Page 96 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: INSERT CLAMP BOLT POINTING AWAY FROM TIRE NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-16: Hydraulic Fold Layout 9450FH-38’ - 42’ LH 3-20 F-1139-0123...
  • Page 97 TABLE OF CONTENTS NOTE: INSERT CLAMP BOLT POINTING AWAY FROM TIRE NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-17: Hydraulic Fold Layout 9450FH-38’ - 42’ RH 3-21...
  • Page 98 TABLE OF CONTENTS Table provided for general use. NOTES: 3-22 F-1139-0123...
  • Page 99 3/4-16 MALE HOSE COUPLER 90° #8 ADAPTER 3-1/2 X 10 CYLINDER BLUE HOSE WRAP FRONT OF MACHINE 90° #8 ADAPTER 16 PORT MANIFOLD #8 45° ADAPTER #8 TO #8 ADAPTER DETAIL A Figure 3-18: Hydraulic Lift Installation 9450FH-46’ - 50’ 3-23...
  • Page 100 ALL HOSE CLAMPS & LOOPS NOTE: INSERT CLAMP NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS, LOOPS, HOSE MOUNTS BOLT POINTING AWAY AND HOLE OF BEARING CAP WELDMENTS FROM TIRE Figure 3-19: Hydraulic Lift Layout 9450FH-46’ - 50’ LH 3-24 F-1139-0123...
  • Page 101 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH NOTE: INSERT CLAMP ALL HOSE CLAMPS, LOOPS, HOSE MOUNTS BOLT POINTING AWAY AND HOLE OF BEARING CAP WELDMENTS FROM TIRE Figure 3-20: Hydraulic Lift Layout 9450FH-46’ - 50’ RH 3-25...
  • Page 102 TABLE OF CONTENTS Table provided for general use. NOTES: 3-26 F-1139-0123...
  • Page 103 #10 TO #8 MANIFOLD ADAPTER 16 PORT #8 TO #8 DETAIL B MANIFOLD #8 JIC ADAPTER ADAPTER DETAIL A 90° #10 #8 TO #8 FRONT OF YELLOW ADAPTER ADAPTER MACHINE HOSE WRAP Figure 3-21: Hydraulic Fold Installation 9450FH-46’ - 50’ 3-27...
  • Page 104 TABLE OF CONTENTS NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS NOTE: INSERT CLAMP BOLT POINTING AWAY FROM TIRE NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-22: Hydraulic Fold Layout 9450FH-46’ - 50’ LH 3-28 F-1139-0123...
  • Page 105 TABLE OF CONTENTS NOTE: INSERT CLAMP BOLT POINTING AWAY FROM TIRE NOTE: RUN HOSES THROUGH ALL HOSE CLAMPS & LOOPS Figure 3-23: Hydraulic Fold Layout 9450FH-46’ - 50’ RH 3-29...
  • Page 106 TABLE OF CONTENTS Table provided for general use. NOTES: 3-30 F-1139-0123...
  • Page 107 TABLE OF CONTENTS 7-PIN 4-PIN CIRCUIT WIRE COLOR CONN. TOWER GROUND WHITE – WORK LAMPS BLACK LEFT FLASHING YELLOW & TURN – STOP LAMPS RIGHT FLASHING GREEN & TURN TAIL LAMPS BROWN SWITCHED – BLUE POWER (12 V) MAIN WARNING LIGHT HARNESS - WIRING CHART RIGHT RIGHT LEFT...
  • Page 108 Assembly” on page 3-6.) 5. Attach the ag red single LED lamps and reflector assembly to tail light mounts using 1/4 x 1-1/2 bolts 10. Install the Landoll decal to the rear of the cylinder and lock nuts. mount rear.
  • Page 109 SIS 20 MPH DECAL, SMV EMBLEM 1/4 X 1 BOLTS, LOCK NUTS 1/4 X 1-1/2 BOLTS & LOCK NUT DETAIL A RED AG CYLINDER LANDOLL LAMP MOUNT DECAL REAR REFLECTOR ASSEMBLY, INCLUDES MOUNT, SMV MOUNTING RED & ORANGE REFLECTOR BRACKET, 5/8 X 2-1/2...
  • Page 110 TABLE OF CONTENTS NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE CLAMPS ALONG HYDRAULIC HOSES NOTE: RUN LIGHT HARNESSES THROUGH ALL HOSE LOOPS ALONG HYDRAULIC NOTE: SECURE HOSES LIGHT HARNESSES WITH TIES STRAPS TO KEEP CLEAR OF ANY MOVING PARTS NOTE: RUN LIGHT HARNESS THROUGH HOSE CLAMPS...
  • Page 111 TABLE OF CONTENTS Table provided for general use. NOTES: 3-35...
  • Page 112 TABLE OF CONTENTS Tine Installation 2. Attach 2-3/4 danish sweep to stem with 7/16 x 1-3/4 oval plow bolts, 7/16 flange nuts. See Figure 2-2 through for tine placement Install the lower stem through hole in the rear of the dimensions.
  • Page 113 TABLE OF CONTENTS 5/8 X 5-1/2 BOLT, 5/8 FLANGE LOCK NUT CLAMP TINE 5/8 X 1-3/4 BOLT, 5/8 FLANGE LOCK NUT SPRING CLAMP STEM TINE SHANK SPACER 2-3/4 DANISH SWEEP, 7/16 X 1-3/4 PLOW BOLT, 7/16 FLANGE NUT Figure 3-27: Shank Installation 3-37...
  • Page 114 TABLE OF CONTENTS 3 Row Coil Tine and Reel Harrow 3. Attach reel assemblies or flat reel assemblies to the reel arm assemblies using 5/8 x 3-11/16 x 4-5/8 Installation u-bolts and 5/8 lock nuts. 5. Attach flat bar reels with angled blades as shown See Figures 2-8 through 2-19...
  • Page 115 TABLE OF CONTENTS 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP BUSHING, 3/4 LOCK NUT TINE & REEL ASSEMBLY 3/4 X 5-1/2 BOLT, 3/4 LOCK NUT NOTE: REMOVE STOP BOLTS AND ROTATE DOWN WITH STOP BOLTS ABOVE TINES DETAIL A NOTE: FRONT ROW TINE SHIPPING POSTION DETAIL A...
  • Page 116 3 Row Spike and Reel Harrow for proper 1. Attach the 3 RSD w/spring and 3 RSD w/o spring placement. (Models 9450FH-38’-42’ only) arm assemblies to the 3. Refer to Note: spike bar alignment See Figures 3-30 rear tube of the center and wing frames using harrow for proper alignment of spike bar assemblies.
  • Page 117 NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 3/4 X 5-1/2 BOLT, HARROW MOUNTING SHANK WELDMENT PLATE, 3” CLAMP USED ON MODELS BUSHING, 9450FH-42’-50’ ONLY 3/4 LOCK NUT 3 RSD ARM ASSEMBLY W/SPRING 3 RSD ARM ASSEMBLY W/O SPRING 3/4 X 5-1/2 BOLT,...
  • Page 118 TABLE OF CONTENTS 2RS DBL Flat Reel Installation NOTE The harrow arms with the catch tray hooks are used See Figures 2-32 2-43 for 2 row spike and double flat on the outer wings with the catch tray hooks toward reel placement dimensions of spike harrow arms, spike bars, and usage of bar clamps or bar clamps w/ tabs.
  • Page 119 TABLE OF CONTENTS NOTE: SPIKE BAR ALIGNMENT RIGHT SIDE SHOWN 3/4 X 5-1/2 BOLT, HARROW MOUNTING PLATE, 3” CLAMP 3 RSD ARM BUSHING, ASSEMBLY 3/4 LOCK NUT W/O SPRING 3 RSD ARM ASSEMBLY W/SPRING CATCH TRAY 1/2 X 3 BOLT DOUBLE FLAT BAR CLAMP REEL ASSEMBLY...
  • Page 120 TABLE OF CONTENTS Rear Tow Hitch (Option) 1. Unfold and lower the field cultivator to the ground. 8. Attach the front of the tow hitch assembly to the cultivator frame cross tubes using 5/8 x 3-11/16 x 2. Install the weight hitch plate on top of the hitch and 5-1/2 u-bolts, 5/8 x 6 hex bolts and 5/8 lock nuts.
  • Page 121 TABLE OF CONTENTS WEIGHT TIE-STRAP HITCH PLATE NOTE: ROUTE HOSES ALONG OTHER HOSES, THROUGH HOSE CLAMPS, ALONG CENTER FRAME, AND HITCH TO FRONT OF MACHINE FRONT FRONT WEIGHT HOSE CLAMP LOCK PLATE 3/4 X 4-1/2 3/8 X 2-3/4 HEX BOLT & HEX BOLT &...
  • Page 122 TABLE OF CONTENTS 26” 26” NOTE: LOCATION OF 12” SHANK EXTENSION RIGHT REAR TANDEM LIGHT USED WITH REAR TOW HITCH TAIL LIGHT MOUNT HARNESS NOTE: CENTER LIGHTING MODULE REAR TOW HITCH ON CENTER FRAME MAIN WIRING HARNESS NOTE: ROUTING OF REAR TOW TANDEM LIGHT HARNESS HITCH ASSEMBLY...
  • Page 123 Chapter 4 TABLE OF CONTENTS Operation DANGER DANGER DANGER DANGER Never allow anyone to ride on the 9450FHField When transporting the unit, place cylinder Cultivator at any time. Allowing a person to ride lockouts in the transport lock position after fully on the machine can inflict serious personal injury extending the cylinders.
  • Page 124 TABLE OF CONTENTS Hydraulic Lift System 1. The rephasing hydraulic lift system contains smaller wing frame cylinders plumbed in series with larger The Field Cultivator is equipped with a rephasing center frame cylinders. It is important that the hydraulic lift system to raise and lower the unit in the field. cylinders be connected in the proper series for the lift system to operate correctly.
  • Page 125 TABLE OF CONTENTS Table provided for general use. NOTES:...
  • Page 126 TABLE OF CONTENTS Hydraulic Fold System 3. The hydraulic fold system is equipped with restrictors in the cylinders to prevent uncontrolled falling of wing The Field Cultivator is equipped with a hydraulic fold frames when folding/unfolding. Removal or improper system to raise and lower the wing frames for narrow assembly of these restrictors can cause the machine transport.
  • Page 127 TABLE OF CONTENTS NOTE: BOTH SIDES ARE EITHER FOLDED OR UNFOLDED DEPENDENT ON OPERATION DETAIL A DETAIL B TRANSPORT LOCK PIN STORAGE LOCATION WHEN FOLDED DETAIL B WING STABILIZER BRACKET MOUNT DETAIL A WING STABILIZER BRACKET MOUNT TRANSPORT LOCK PIN STORAGE LOCATION WHEN UNFOLDED Figure 4-4: Wing Stabilizer Bracket Locks...
  • Page 128 TABLE OF CONTENTS Transporting 3. When towing in combination, the maximum equipment ground speed shall be limited to the 1. Check and follow all federal, state, and local lowest specified ground speed of any of the towed requirements before transporting the Field Cultivator. implements.
  • Page 129 6. Check that tires are of proper size, load rating, and inflated to manufacture specifications before The Landoll 9450FH Field Cultivator is designed to be transporting. Check wheel lug bolts to insure pulled by tractor equipped with a double lip or clevis type tightness.
  • Page 130 TABLE OF CONTENTS Leveling (Side to Side) 3. To adjust the radius rod’s, loosen the 1-3/4” locking nut against the radius rod tube. Adjust the screw 1. Leveling the Field Cultivator side-to-side involves adjustment in or out to the desired setting. An leveling the center frame then leveling the wing adjusting wrench is provided to make this frames to the center frame.
  • Page 131 TABLE OF CONTENTS 9450FH Gauge Wheels NOTE Initially the front radius rods are set to 21”on center 1. The front gauge wheels of the floating hitch cultivator before final adjustment raise and lower with center and wing lift wheels See Figure 4-7...
  • Page 132 TABLE OF CONTENTS Depth Stop Adjustment LED Light Operation 1. The operating depth of the Field Cultivator is 1. Attach the seven-pin plug to the socket at the rear of controlled by a single-point depth stop. The stop is the tractor. The socket must be in good working located at the center front of the machine order, and free of dirt, grease, and corrosion.
  • Page 133 TABLE OF CONTENTS 9400 Danish Tine Shank 1. The 9400 series field cultivator uses a two-piece are 40mm (1.57”) centers and accepts 12mm (7/16”) Danish-tine shank assembly. Shanks are spaced on mounting bolts. 4” centers, on a split-the-middle pattern. The shanks Install the lower stem through hole in the rear of the are configured on a true 6-row pattern for greater spring clamp.
  • Page 134 TABLE OF CONTENTS 3 Row Coil Tine and Reel Adjust- 4. Each coil tine harrow may be adjusted for spring pressure as well See Figure 4-10. Raise the tine ments harrow off the ground. Adjust the spring pressure the same for both harrow arms on each section. Remove 1.
  • Page 135 TABLE OF CONTENTS SPRING TINE ANGLE ASSEMBLY MORE LESS 1-8 HEX NUTS AGGRESSIVE AGGRESSIVE 1/2” 21-3/4” REEL TINE SPRING ASSEMBLY PRESSURE HEAVY CLEVIS PIN HARROW LIGHT ADJUSTMENT PIN CLEVIS PIN HARROW ADJUSTMENT PIN REEL 3 ROW COIL TINE ASSEMBLY ASSEMBLY HARROW ADJUSTMENT HOLES Figure 4-10: 3 Row Coil Tine and Reel Adjustments...
  • Page 136 TABLE OF CONTENTS 3 Row Spike and Reel Adjust- 5. The 12” diameter reel consists of nine 3/4” diameter round bars with a chevron shape for smoother ments rotation. The reels have no inner shaft to reduce plugging in wetter conditions. The reels operate 1.
  • Page 137 TABLE OF CONTENTS LEAST TOOTH ANGLE MIDDLE TOOTH ANGLE SPRING SPRING CARRYING CHAIN MOST TOOTH ANGLE ASSEMBLY ASSEMBLY 1-8 HEX NUTS 21-3/4” REEL ASSEMBLY FORWARD PULL CHAIN HARROW ADJUSTMENT PIN BAR CLAMP BAR CLAMP W/TABS SPIKE BAR ASSEMBLY CLEVIS PIN REEL ASSEMBLY Figure 4-11: 3 Row Spike and Reel Adjustments...
  • Page 138 TABLE OF CONTENTS 2RS DBL Flat Reel Adjustments 3. For the most aggressive spike tooth action, install the harrow adjustment pin in the forward mounting hole 1. The optional 2 row spike and reel attachment over each bar clamp for each spike bar consists of a 2 row spike and double finishing reel Figure 4-12.
  • Page 139 TABLE OF CONTENTS LEAST TOOTH ANGLE SPRING SPRING MIDDLE TOOTH ANGLE ASSEMBLY ASSEMBLY CARRYING CHAIN MOST TOOTH ANGLE 1-8 HEX NUTS 21” REEL FORWARD ASSEMBLY PULL CHAIN HARROW ADJUSTMENT PIN BAR CLAMP W/TABS SPIKE BAR DOUBLE FLAT ASSEMBLY REEL ASSEMBLY CLEVIS PIN Figure 4-12: 2RS DBL Flat Reel Adjustments 4-17...
  • Page 140 TABLE OF CONTENTS Table provided for general use. NOTES: 4-18 F-1139-0123...
  • Page 141 TABLE OF CONTENTS Chapter 5 Maintenance and Lubrication Wheel Bearing Maintenance – Wheel Bearing Maintenance -- Non Triple-Lip Triple-Lip Wheel bearing maintenance should be performed at the Transport tires use a self-contained seal with multiple beginning of every season of use. Check the wheel lips.
  • Page 142 TABLE OF CONTENTS Lubrication fittings before greasing. Replace any lost or broken fittings immediately. 1. A proper maintenance schedule will insure a long 3. Wheel seals, when properly installed, will allow operating life and peak performance. Performing the grease to pass without harm to seals. Regular following lubrication will ensure maximum operating lubrication will extend service life, particularly in life of the Field Cultivator...
  • Page 143 TABLE OF CONTENTS Storage 1. The service life of the Field Cultivator will be extended by proper off-season storage practices. Prior to storing the unit, complete the following procedures: a. Completely clean the unit. b. Inspect the machine for worn or defective parts. Replace as needed.
  • Page 144 TABLE OF CONTENTS Table provided for general use. NOTES: F-1139-0123...
  • Page 145 Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 9450FH Field Cultivator. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM...
  • Page 146 TABLE OF CONTENTS PROBLEM PROBABLE CAUSE SOLUTION SWEEPS NOT CUTTING, LEAVING Shanks not positioned correctly Check for proper shank placement SKIPS Sweeps not wide enough Use wider sweeps Sweeps set too shallow Increase operating depth Incorrect sweep angle Use 47 degree sweeps Incorrect shank spring adjustment Adjust spring shank.
  • Page 147 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 10/07/2022 F-1139 New Manual 01/10/2023 F-1139-0123 Initial Release...
  • Page 148 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Model 9450FH Field Cultivator Operators Manual Re-Order Part Number F-1139 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...