Advertisement
Available languages
Available languages
BASF1314/1714I05M1 visual.qxd
2/25/06
10:25
Page 4
BASF1314/1714
Fig. 1
E
D
F
C
B
R
A
O
P
U.K. and IRELAND
PLEASE READ AND SAVE THESE
INSTRUCTIONS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
precautions should always be taken including
G
H
the following:-
• Use the fan only for purposes described in
the instruction manual.
• To protect against electrical shock, do not
immerse the fan, plug or cord in water or
spray with liquids.
• Close supervision is necessary when any
appliance is used by or near children.
• Unplug from the electrical outlet when not in
use, when moving the fan from one location
to another, before putting on or taking off
parts and before cleaning.
J
• Avoid contact with any moving parts.
• Do not operate in the presence of explosive
and/or flammable fumes.
• Do not place the fan or any parts near an
open flame, cooking or other heating
I
appliance.
K
• Do not operate any appliance with a damaged
cord, plug, after the appliance malfunctions,
or has been dropped/damaged in any
manner.
• The use of attachments not recommended or
L
sold by the appliance manufacturer may
cause hazards.
• Do not use outdoors.
M
• Do not let the cord hang over the edge of a
table or counter, or come into contact with hot
surfaces.
• To disconnect from the electrical supply, grip
the plug and pull from the wall outlet. DO
NOT pull on the cord.
N
• Always use on a dry, level surface.
• Do not operate without the fan grills properly
in place.
• This product is intended for household use
ONLY and not for commercial or industrial
applications.
MISSING A PART FOR YOUR FAN?
Please call 0800 052 3615 for assistance.
ASSEMBLY INSTRUCTIONS (See Fig 1.)
Base/Pole assembly
S
You will need the base cover (O), round
weighted insert (P), pole (K,M), pole ring (N)
Q
washer (S) and L-shaped locking lever (Q).
1. Slide the bottom end of the pole through the
pole ring.
Converting to a table fan -
2. Turn the base cover upside down and place
the round weighted insert into the base cover.
Model BASF1314 only: On model BASF1314 an
3. Insert the threaded end of the L-shaped
additional short pole (R) is supplied which allows
locking lever into the hole of the washer, round
the fan to be converted into a table fan. To
weighted insert and through the base cover.
change to this short pole, remove the fan head
assembly from its position on top of the inner
4. Whilst holding the base cover and round
weighted insert with one hand, connect the
pole and unscrew the L-shaped locking lever at
pole to the base, sliding the L-shaped locking
the base. Remove the long pole, replace with the
lever into the bottom of the pole with you other.
short pole and reassemble as detailed above.
5. Turn the L-shaped locking lever clockwise to
OPERATING INSTRUCTIONS
securely attach the pole to the base.
1. Set the fan base on a dry level surface
6. Set the base on the floor, weight side down.
2. Make sure the Selector (Speed) Control is in
Push the pole ring down until it sits directly on
the OFF position. Selector (Speed) Control is
the base.
located on the top of the fan motor housing.
Fan head assembly
3. Plug the cord into a suitable 220-240V. AC
You are now ready to assemble the fan head
outlet.
1. Unscrew rear grill mounting nut (D) before
4. The SPEED is adjusted by turning the Selector
positioning the rear grill (F) over the motor
(Speed) Control to the desired setting:-
shaft (G) making certain that the notches at
O-III-II-I.
the top and bottom of the rear grill, fit over the
5. The OSCILLATION control is located on the
prongs on the motor housing (H).
top of the fan motor housing. To start
2. Secure the rear grill in its place using the rear
oscillation, push the control knob down.
grill mounting nut (D). Turn this nut clockwise
To stop oscillation, pull the control knob up.
and tighten firmly.
ADJUSTMENT
3. Slide the fan blade (B) with the hollowed
Tilt adjustment
interior of the blade facing toward the rear
Follow these instructions to tilt the fan head for
grill, firmly onto the motor shaft. The top of the
upward angle air movement.
motor shaft should lie even with the centre of
1. To change the tilting angle of the fan head,
the fan blade.
simply loosen the tilt adjustment knob (J)
4. Now use the securing screw (C) (already
2. Move the fan head to the desired angle, then
attached to the Fan Blade) to lock the blade
firmly tighten the knob to lock in place.
into place. Tighten the screw into the side hole
Height adjustment
of the fan blade, against the motor shaft, until
Follow these instructions to adjust the height of
both the blade and screw are secure.
5. Centre the front grill (A) by aligning the Bionaire®
the fan.
1. Turn the pole locking knob (L) anti-clockwise
logo on the logo plate so that it is horizontal
and parallel with the floor. Then, holding the
to loosen the pole.
front grill against the rear grill, push the black
2. Adjust the pole to the desired height and
firmly tighten the locking knob in a clockwise
grill ring (E) into place at the top and bottom of
the fan. (Push directly on the black grill ring,
direction.
not on the grills themselves). Finish securing
CLEANING AND MAINTENANCE
the grill ring in the same manner until both
Follow these instructions to correctly and safely
grills are joined underneath the black ring.
care for your Bionaire
Final assembly
• Always unplug the fan before cleaning or
assembly.
1. Slide the inner pole extension (K) up from the
outer pole (M). Insert the pole locking knob (L)
• Do not allow water to drip on or into the fan
into the hole on the outer pole, to securely
motor housing.
• Be sure to use a soft cloth, moistened with a
hold this position.
2. Place the fan head assembly into this extension
mild soap solution.
• Do not use any of the following as a cleaner:
pole, inserting the neck of the fan into the pole
opening. Turn the fan head's neck until the
petrol, thinners or benzene.
head is securely locked into place.
Fan Blade cleaning
3. Add the tilt adjustment knob (J) to the hole in
(See instructions for fan head assembly)
the fan head's neck. Tighten when the fan head
1. To access the fan blade, remove the front grill
is in your desired position.
and securing screw.
2
2. Clean the fan blade, front and rear grills with
a soft moist cloth.
3. Replace the fan blade, tighten screw and
securely fasten the front grill.
Fan head, base and pole cleaning
Using a soft, moist cloth, with or without a mild soap
solution, carefully clean the fan base, pole and
head. Please use caution around the motor housing
area. Do not allow the motor or other electrical
components to be exposed to water.
FAN STORAGE
Your fan can be stored either partially disassembled
or assembled.
It is important to keep it in a safe, dry location.
• If stored disassembled, we recommend using
the original (or appropriately sized) box.
• If stored assembled or partially assembled,
remember to protect the fan head from dust.
FITTING A REPLACEMENT PLUG (UK
ONLY)
The wires in this mains lead are coloured in
accordance with the following code:
Blue
-
Neutral
Brown
-
Live
This appliance is fitted with a 13 amp plug. The
fuse should be rated at 3 amps and ASTA
approved to BS1362.
However if the plug is unsuitable, it should be
removed from the supply cord and an
appropriate plug fitted as detailed below:-
As the colours of the wires in the mains lead of
this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows:-
The wire which is coloured Blue must be
connected to the terminal which is marked with
the letter N or coloured Black.
The wire which is coloured Brown must be
connected to the terminal which is marked with
the letter L or coloured Red.
fan. Please remember:-
®
NB. Neither wire should be connected to the
terminal in your plug which is marked with the
letter E or by the Earth symbol
or coloured
Green or Green and Yellow. If in doubt consult a
qualified electrician.
If any other plug is used, a 3 amp fuse must be
fitted either in the plug or adaptor or at the
distribution board.
3
Advertisement
