Download Print this page

Pichler Albatross Manual

Balsawood airplane

Advertisement

Quick Links

Vor dem Flug:
● Prüfen Sie die Servo-Mittelstellung
● Prüfen Sie die Drehrichtung des Motors.
● Legen Sie den Schwerpunkt wie in der Anleitung fest. Ggf. müssen Sie zum Ausgleich Gewichte in die Nase legen.
● Prüfen SIe alle Anschlüsse im Rumpf sowie alle verbauten Komponenten.
● Seien Sie beim An- und Abstecken des Akkus vorsichtig. Tauschen Sie den Akku beim ersten Anzeichen von
Niedrigspannung
SICHERHEITSHINWEISE
Dieses Produkt ist kein Spielzeug. Ihre Sicherheit ist davon abhängig, wie Sie mit diesem Modell umgehen , Bei falschem
oder unvorsichtigem Umgang kann es zu Verletzungen kommen. Kinder müssen permanent von einer Aufsichtsperson
überwacht werden solange sie dieses Modell fliegen. Nicht für Kinder unter 14 Jahren geeignet.
DIESES MODELL IST KEIN SPIELZEUG.
● Nur auf zulässigen Plätzen fliegen.
● Empfängerreicheweite prüfen und einhalten.
● Als Anfänger nicht ohne Aufsicht fliegen.
● Außer Reichweite von Kindern aufbewahren.
● Dieses Modell kann Fiberglas und Carbonfasern enthalten. Bei der Bearbeitung des Materials Schutzkleidung wie Brille und Handschuhe
tragen.
HINWEIS: Änderungen und Irrtümer vorbehalten. Besuchen Sie die Produktseite in
unserem Onlineshop um die akutellste Anleitung zum Produkt einzusehen.
www.pichler-modellbau.de
Albatross
Balsawood Airplane

飞行参数
推荐配置
Suggested Equipment
Specification
翼展:1800mm(70.8 inch)
油动:
2冲程 20cc gasoline(DLE-20CCRA)
机长:1430mm(56 inch)
4冲程 30cc gasoline
2冲程 90class Methanol
起飞重量: 5kg
4冲程 120class Methanol
Wingspan:1800mm (70.8inch)
Fuselage Length:1430mm (56inch)
电动:
马达 4220-5030 410KV-300KV
Flying weight:5KG (About 11 pound)
电池 6S 4000-6000mAh
电调 80-150A (6S)
其他:
桨叶 16寸
舵机 37g*2+1pcs / 17g*2pcs
Y线 1pcs
延长线 30cm 4pcs
工具
Tools Needed
GP:
2-stroke 20cc gasoline(DLE-20CCRA)
4-stroke 30cc gasoline
2-stroke 90class Methanol
4-stroke 120class Methanol
EP:
Motor :4220-5030 410KV-300KV
BATT
:6S 4000-6000mAh
ESC
: 80-150A (6S)
Propeller: 16 inch
Servo: 37g*2+1pcs / 17g*2pcs
Y wire 1pcs
Extension wire 30cm *4pcs

Advertisement

loading
Need help?

Need help?

Do you have a question about the Albatross and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Pichler Albatross

  • Page 1 Albatross Balsawood Airplane  Vor dem Flug: ● Prüfen Sie die Servo-Mittelstellung ● Prüfen Sie die Drehrichtung des Motors. ● Legen Sie den Schwerpunkt wie in der Anleitung fest. Ggf. müssen Sie zum Ausgleich Gewichte in die Nase legen. ● Prüfen SIe alle Anschlüsse im Rumpf sowie alle verbauten Komponenten.
  • Page 2 配件图仅做参考用,您收到的实物可能因为修改/优化的原因导致与图片有略有不同。 01-8 Photos shown here just for reference, the product you received maybe slightly differ from the photos due to continuous improvement on products. F6&F6-1 F6&F6-1 F7&F7-1 F9&F9-1 F8&F8-1 F30-1 01-10 F5-2 木件 碳管,碳片,玻纤件 起落架,配件,拉线等 F30-2 F30-2 Wood pieces Carbon tube, carbon sheet, fiberglass parts Landing gear, accessories, stay wire, etc.
  • Page 3 在图示位置装入PVC导管 01-20 01-21 Install the PVC conduit in 01-15 the position shown F38-1 F35-2 F35-2 F35-1 左右相同安装 左右相同安装 Same installation on left and right Same installation on left and right 01-22 01-16 F12&F12-1 F11&F11-1 F34-2 堆叠粘固,并打磨圆滑 Stack and bond, and polish smooth F34-1 F34-2 F35-1...
  • Page 4 细节1 Detail 1 细节1 Detail 1 细节2 Detail 2 细节3 Detail 3 机身横梁和蒙板安装请参考1:1图纸 Please refer to the 1:1 drawing for the 细节2 Detail 2 installation of the fuselage beam and mask 舱盖拼装 Assemble the Hatch 细节3 Detail 3 P8-1 P0-3 P0-6 P0-2 P0-3...
  • Page 5 机翼安装 舵机线从机翼内侧预留孔 如图切槽装入纸合页 05-3 M3 自锁螺母 Assemble the Wing 导出。 Insert the paper hinge M3 self-locking nut The servo line is led out into the slot as shown 后续安装的玻纤支架均参照1:1图纸,对比长度选择正确的部 from the reserved hole in the figure 件安装。玻纤支架建议喷黑漆后再进行安装。 纸合页 inside the wing. The subsequent installation of the fiberglass bracket Paper hinges refers to the 1:1 drawing, and selects the correct compo-...
  • Page 6 尾翼及滑橇安装 把转向舵通过纸合页与垂直尾翼连接 ,连接处点入CA粘合,并保持舵面 细节 1 Assemble the tail and skid 可以自由摆动。 05-9 Detail 1 Connect the steering rudder to the vertical tail with paper hinges. 如图切槽装入纸合页 The joints are glued with CA and keep the rudder surface 06-1 Insert the paper hinge swinging freely.
  • Page 7 06-9 细节 2 细节 3 06-6 细节 1 Detail 2 Detail 3 Detail 1 弹簧 spring 铝扣 aluminum buckle 细节 4 滑橇安装完成后,用美工刀切除与机身结合面的蒙皮。 06-7 Detail 4 After installing the skid, use a utility knife to cut off the covering film on the joint surface with the fuselage. 拉线用铝扣锁定,通过弹簧挂在机翼...
  • Page 8 Install the power system/ propeller 此款信天翁提供2种马达安装座,分别对应油动引擎,电动马达。请根据您所 选的动力分别安装,此处展示安装图示供参考。 This Albatross provides two types of motor mounts, which correspond to oil-powered engine and electric motor. Please install separately according to the power you selected. The installation diagram is shown here for reference.
  • Page 9 用自攻螺丝固定飞行员木板座到 机身,方便后期调试时可以取下 Fix the pilot board seat to the 使用油动引擎时可能需要在机头部进行配重,并且油箱放置在重心位置。 fuselage with self-tapping When using an oil-powered engine, it maybe necessary to counterweight the screws, which can be removed head of the airplane, and the oil tank is placed at the center of gravity. during later debugging.
  • Page 10 升降杆上推 Lifting rod up 转向杆向右 Steering rod to the right 转向杆向左 Steering rod to the left 方向杆向右 Direction rod to the right 方向杆向左 Direction rod to the left Pichler Modellbau GmbH - Lauterbachstr. 19 - 84307 Eggenfelden mail@pichler.de | 08721-5082660...

This manual is also suitable for:

Albatros d.iiiPi-15481