1:10 scale 2wd electric off road competition buggy kit (34 pages)
Summary of Contents for Associated Electrics RC10 TEAM CAR GOLD EDITION
Page 2
• Green Slime shock lube (AE #1105) • Calipers or a Precision Ruler • Wire Cutters / Hobby Knife • Needle Nose Pliers • Soldering Iron Associated Electrics, Inc. Customer Service 21062 Bake Parkway Tel: 949.544.7500 Lake Forest, CA 92630 Fax: 949.544.7501...
Page 4
This symbols indicates a line up your hardare with the correct drawing special note or instruction until you find the exact size. in the manual. Associated Electrics, Inc. Customer Service 21062 Bake Parkway Tel: 949.544.7500 Lake Forest, CA 92630 Fax: 949.544.7501 http://www.AssociatedElectrics.com •...
Page 5
12/24 :: Nose Plate / Steering Build - Bag A - Step 1 :: Nose Plate / Steering Build - Bag A - Step 1 7811 RC10 body #8 aluminum mounts washer (thick) 6637 Washers are used 6637 RC10 front to adjust to your RC10 nose plate,...
Page 6
:: Front Suspension Front Suspension Build Build - Bag B - Bag B - - Step 2 Step 2 6299 6204 E-clip Front wide (small) arms, (Left & Right) 6299 E-clip (small) 6644 RC10 front 6644 outer RC10 hinge pins king pins Build left and right sides! :: Front Suspension...
Page 7
:: Transmission Transmission Build Build - Bag C - Bag C - - Step 1 Step 1 6579 Diff thrust Diff drive 6579 washer rings Diff drive rings Diff thrust balls, cage 6578 Diff 6578 outdrives Diff outdrives Build Tip: 6573 Install the first washer (grove up), Diff thrust...
Page 8
:: Transmission Transmission Build Build - Bag C - Bag C - - Step 4 Step 4 7812 3977 Idler gear Bearing 6571 3977 and shaft 3/16 x 3/8 Drive gear Bearing roll pin 3/16 x 3/8 6565 3976 6571 RC10 Stealth Bearing Drive gear...
Page 9
:: Rear Rear Bulkhead Bulkhead Build Build - Bag D - Bag D - Step 1 - Step 1 4-40 x 5/16 4-40 nuts 4-40 x 3/8 SHCS SHCS 4-40 x 3/4 SHCS 6323 6645 RC10 rear RC10 rear bulkhead 6271 shock tower Ballstud...
Page 10
:: Rear Rear Bulkhead Bulkhead Build Build - Bag D - Bag D - Step 4 - Step 4 6638 RC10 wing 4-40 x 1/2 4-40 x 5/16 tubes SHCS SHCS Press wing tubes into bulkhead! #4 aluminum washer 4-40 x 1/4 SHCS :: Rear Rear Suspension...
Page 11
:: Rear Rear Suspension Suspension Build Build - Bag E - Bag E - Step 3 - Step 3 6644 RC10 rear outer hinge pins 6299 E-clip (small) Build left and right sides! :: Turnbuckles Build Turnbuckles Build - Bag F - Bag F - Step 1 - Step 1 Orient the notch...
Page 12
:: Turnbuckles Build Turnbuckles Build - Bag F - Bag F - Step 3 - Step 3 6279 6267 Orient the notch Ball cups Steel turnbuckle, to the left (white) black (1.65”) throughout the car. It indicates which end has the Front Camber Turnbuckle left hand threads! 1.14”...
Page 13
:: Shocks Build Shocks Build - Bag G - Bag G - Step 2 - Step 2 Front Rear Rear 6437 Shock Shock Shock Shock FT Hard 5407 6435 Anodized Red o-ring FT Hard shock body, Place on table Anodized front (0.71) and push down shock body,...
Page 14
:: Shocks Build Shocks Build - Bag G - Bag G - Step 5 - Step 5 Front: 6.5mm Rear: 6639 Front shock RC10 shock spring, silver collar (3.85lb) 6639 RC10 Rear shock spring cup 4-40 x 3/8 spring, silver SHCS (2.10lb) Build two front and two rear!
Page 15
:: Chassis Build Chassis Build - Bag H - Bag H - Step 1 - Step 1 6338 6638 Antenna tube RC10 nose and cap brace tubes 7811 RC10 4-40 x 3/8 antenna 4-40 x 1/4 BHCS mount BHCS 4-40 x 3/8 FHCS Build left and right sides! :: Chassis Build...
Page 16
:: Electronics Build Electronics Build - - Bag I Bag I - Step 3 - Step 3 Follow steps below to properly install Z bend wire into servo horn and steering link. #4 aluminum NOTE: Hole choice may vary depending on washer servo and servo horn used.
Page 17
:: Electronics Build Electronics Build - - Bag I Bag I - Step 6 - Step 6 Battery not included! 6332 Body clip :: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 1 - Step 1 6872 Front Tire,...
Page 18
:: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 3 - Step 3 Painting Tips: 6159 RC10 Protech Your RC10 Kit comes with a clear polycarbonate body and wing. Buggy body, You will need to prep the body and wing before you can paint unpainted...
Page 19
:: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 6 - Step 6 6332 6639 6332 Body Wing Body clip mounts clip 6121 RC10 Viper body, clear 6182 High downforce wing, 5.5”...
Page 20
:: Wheels / Tires and Body :: Wheels / Tires and Body - - Bag J Bag J - Step 9 - Step 9 TIP: Bend wire to create tight fit inside wing tubes.
Need help?
Do you have a question about the RC10 TEAM CAR GOLD EDITION and is the answer not in the manual?
Questions and answers