Download Print this page
Lithonia Lighting TITAN Series Installation Instructions
Lithonia Lighting TITAN Series Installation Instructions

Lithonia Lighting TITAN Series Installation Instructions

Advertisement

Quick Links

CAUTION: For safety and proper operation, read and follow instructions carefully before installation
PARTS DESCRIPTION
Housing
Transformer
Front Cover
Battery
Lamp Head
Charger Board
BEFORE INSTALLATION
Unit should be located to assure adequate clearance for front cover
and lamp housing
orientation.
Do not position unit where it will be exposed to direct sunlight,
radiators, or other heat sources. Prolonged exposure to high
temperatures will shorten battery life and may void warranty.
CAUTION: Damage to battery will occur if battery is connected to
charger board for a prolonged period of time without AC power
provided.
INSTALLATION INSTRUCTIONS
MODELS ELT50 / ELT125 / ELT180 / ELT250 / ELT275
SERIES
IMPORTANT SAFEGUARDS
1. READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
2.
Do not use outdoors.
3.
Do not let power supply cords touch hot surfaces.
4.
Do not mount near gas or electric heater.
5.
Use caution when servicing batteries. Battery acid can
burns to skin and eyes. If acid is spilled on skin or
flush acid with fresh water and contact
immediately.
6.
Equipment should be mounted in locations and at heights
where it will not readily be subjected to tampering by
unathorized personnel.
7.
The use of accessory equipment not recommended by the
manufacturer may cause an unsafe condition.
8.
Do not use this equipment for other than intended use.
9.
Before wiring to power supply, turn off electricity at fuse or
circuit breaker.
10. Consult your local building code for approved wiring.
11. Fixture must be grounded to avoid potential electric shock.
12. Disconnect AC power and unplug battery before servicing.
13. All servicing should be performed by qualified personnel.
14. CAUTION: Halogen cycle lamp(s) may be used in this
To avoid shattering, do not operate lamp in excess
voltage. Protect lamp against abrasions and scratches and
against liquids when lamp is operating. Dispose of lamps with
care. Halogen lamps operate at high temperatures. Do not store
or place flammable materials
SAVE THESE
INSTRUCTIONS
Page 1
cause
in eyes,
physician
fixture.
of rated
near lamps.

Advertisement

loading
Need help?

Need help?

Do you have a question about the TITAN Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Lithonia Lighting TITAN Series

  • Page 1 INSTALLATION INSTRUCTIONS SERIES MODELS ELT50 / ELT125 / ELT180 / ELT250 / ELT275 CAUTION: For safety and proper operation, read and follow instructions carefully before installation IMPORTANT SAFEGUARDS 1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS Do not use outdoors. Do not let power supply cords touch hot surfaces. Do not mount near gas or electric heater.
  • Page 2 FIGURE 1 MOUNTING TO WALL USING J-BOX Remove rear knockout and locate over J-Box. Install fasteners with a pullout rating of 80 pounds in the 3 keyway mounting holes and in the lower oblong mounting hole. MOUNTING WITH SURFACE CONDUIT Remove 7/8"...
  • Page 3 INSPECTION AND MAINTENANCE FIGURE4 NOTE: Emergency lighting systems should be tested as often as MODEL ELT50 N local codes require, or at least quarterly, to ascertain that all WITH OPTIONS components are operational. A. NORMAL OPERATION: When unit is functioning properly with A.C.
  • Page 4 FIGURE 6 FIGURE 7 MODEL ELT125 MODEL ELT125 WITH OPTIONS Gnd Clip Gnd Clip NOTE: Metal lampheads (option MT) lamp leads may be black. FIGURE 8 FIGURE 9 MODELS ELT180, MODELS ELT180, ELT250 & ELT275 ELT250, & ELT275 WITH OPTIONS Gnd Clip Gnd Clip NOTE: Yellow lamp lead routing, without load disconnect option, is...

This manual is also suitable for:

Elt50Elt125Elt180Elt250Elt275