Download Print this page
Lithonia Lighting ECRG SQ Instructions

Lithonia Lighting ECRG SQ Instructions

Led combo exit & emergency light

Advertisement

Quick Links

INSTRUCTIONS for Lithonia Lighting ECRG SQ
LED COMBO EXIT & EMERGENCY LIGHT
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND
WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY OR SIGNIFICANT
PROPERTY DAMAGE. For your protection, read and follow these warnings
and instructions carefully before installing or maintaining this equipment.
These instructions do not attempt to cover all installation and maintenance
situations. If you do not understand these instructions or additional
information is required, contact LITHONIA or your local LITHONIA distributor.
WARNING: RISK OF ELECTRIC SHOCK - NEVER CONNECT TO,
DISCONNECT FROM, OR SERVICE WHILE EQUIPMENT IS ENERGIZED.
WARNING: RISK OF FIRE. Lamps are hot. Keep combustible material away from hot parts. Observe lamp manufacture's warnings,
recommendations and restrictions on lamp operation and maintenance. Make sure lamps are correctly installed.
CAUTION: The battery in this unit may not be fully charged. After electricity is connected to unit, let battery charge for at least
24 hours, then normal operation of this unit should take effect. To check, press the TEST button. The lamps on the unit should
turn on. (Refer to OPERATION BATTERY BACK UP for more testing information)
IMPORTANT SAFEGUARDS: When using electrical equipment, basic safety precautions should always be followed,
including the following:
Do not use outdoors. Suitable for use in 0°C-40°C(32°F-104°F) indoor damp locations.
Consult local building code for approved wiring and installation.
Disconnect AC power before servicing and installation.
Do not mount near gas or electric heaters.
Do not use this equipment for anything other than its intended use.
The use of accessory equipment not recommended by the manufacturer will void product listing and warranty and may cause
an unsafe condition.
Any service on this equipment should be performed by qualified personnel only.
Equipment should be mounted in locations and at heights where it will not be subject to
tampering by unauthorized personnel.
Use caution when servicing batteries.
Cap unused wires with enclosed wire nuts or other approved method.
Make sure wire terminations are secure and leads are properly tucked in appropriate wire
channels
NOTE: Max mounting height is 10 ft to achieve at least 1 ft-candle of illuminance in emergency mode.
RED PALSTIC PIECE
Remove or re-insert the red lens from/to face plate.
Secure the green lens to face plate.
SAVE THESE INSTRUCTIONS
and deliver to owner after installation
GREEN PALSTIC PIECE
Toggle the switchable button to choose red or green illumination.
Switchable
button

Advertisement

loading
Need help?

Need help?

Do you have a question about the ECRG SQ and is the answer not in the manual?

Questions and answers

Summary of Contents for Lithonia Lighting ECRG SQ

  • Page 1 INSTRUCTIONS for Lithonia Lighting ECRG SQ LED COMBO EXIT & EMERGENCY LIGHT READ AND FOLLOW ALL SAFETY INSTRUCTIONS WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, SERIOUS INJURY OR SIGNIFICANT PROPERTY DAMAGE. For your protection, read and follow these warnings and instructions carefully before installing or maintaining this equipment.
  • Page 2 INSTRUCTIONS for Lithonia Lighting ECRG SQ NOTE: EXIT ships standard RED. Refer to Toggle Switch section for GREEN LED configuration. INSTALLATION INSTRUCTIONS(back mount): 1. Remove EXIT stencil faceplate from housing. Remove RED lens from faceplate(see fig. A). Set aside. 2. Drill or knock out appropriate knockouts on back plate to fit junction box mounting points.
  • Page 3 INSTRUCTIONS for Lithonia Lighting ECRG SQ LED COMBO EXIT & EMERGENCY LIGHT(cont.) INSTALLATION (relocation of lamp head to top of housing): 1.Remove the mounting hole plug located on the top of the housing. 2.Snap lamp head that was removed from the side of the housing into the mounting hole plug located on the top of the housing.

This manual is also suitable for:

Ecrg ho sq m6