Subscribe to Our Youtube Channel
Related Manuals for Planet IMS-6325-5
Summary of Contents for Planet IMS-6325-5
- Page 1 Industrial L3 5-Slot Modular Managed Ethernet Switch IMS-6325-5 Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ..................3 2. Requirements ....................4 3. Wiring the Power Inputs ................. 5 3.1 Grounding the Device ................6 4. Terminal Setup ....................7 4.1 Logging on to the Console ............... 8 4.2 Configuring IP Address via Console ............9 5. -
Page 3: Package Contents
1. Package Contents Thank you for purchasing PLANET Industrial L3 Modular Managed Switch, IMS-6325-5. The description of the model is follows: Industrial Layer 3 5-Slot Modular Managed Ethernet Switch IMS-6325-5 (-40~75 degrees C) “Industrial Modular Managed Switch” mentioned in this Quick Installation Guide refers to the above model. Open the box of the Industrial Modular Managed Switch and carefully unpack it. -
Page 4: Requirements
2. Requirements The Industrial Modular Managed Switch provides a remote login interface for management purposes. The following equipment is necessary for further management: Workstations running Windows 7/8/10/11, macOS 10.12 or later, Linux Kernel 2.6.18 or later, or other platforms are compatible with TCP/IP Protocols. Workstations are installed with Ethernet NIC (Network Interface Card). Serial Port Connection (Terminal) ... -
Page 5: Wiring The Power Inputs
Contacts 5 and 6 for Power 2. IMS-6325-5: DC 12-48V Alarm Ring R.O. Console 115200,N,8,1 Reset Max. Fault Alarm Loading: 24V, 1A DC Input: 12-48V , 5.5A max. Figure 3-1: IMS-6325-5 Front Panel Tighten the wire-clamp screws to prevent the wires from loosening. Power 1 Power 2 Figure 3-2: Pins of 6-contact Terminal Block Connector... -
Page 6: Grounding The Device
1. The wire gauge for the terminal block should be in the range from 12 to 24 AWG. 2. Please check the wire AWG Ampere specification before connecting PLANET Industrial Modular Managed Switch. PWR1 and PWR2 must provide the same DC voltage for power load balance while operating with dual power input. -
Page 7: Terminal Setup
4. Terminal Setup To configure the system, connect a serial cable to a COM port on a PC or notebook computer and to RJ45 type serial (console) port of the Industrial Modular Managed Switch. Industrial Modular Switch PC/Workstation with Terminal Emulation Software Ring R.O. RJ45 to DB9 RS232 Cable Console 115200,N,8,1 Serial Port Console Port... -
Page 8: Logging On To The Console
(1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. PLANET Technology Corp. Made in Taiwan Figure 4-1: MAC ID Label Enter the default username and password, then set a new password according to the rule-based prompt and confirm it. Upon success, press any key to return to the... -
Page 9: Configuring Ip Address Via Console
To check the current IP address or modify it to a new IP address for the Switch, please use the procedure as follows: Display of the current IP Address 1. At the “#” prompt, enter “show ip interface brief”. IMS-6325-5 # show ip interface brief 2. The screen displays the current IP address shown in Figure 4-3. Figure 4-3: IP Information Screen Configuration of the IP Address 3. At the “#” prompt, enter the following command and press <Enter>... - Page 10 Storing current switch configuration 5. At the “#” prompt, enter the following command and press <Enter>. # copy running-config startup-config Figure 4-5: Saving Current Configuration Command Screen If the IP is successfully configured, the Industrial Modular Managed Switch will apply the new IP address setting immediately. You can access the Web interface of the Industrial Modular Managed Switch through the new IP address. If you are not familiar with the console command or the related param- eter, enter “help”...
-
Page 11: Starting Web Management
5. Starting Web Management The following shows how to start up the Web Management of the Industrial Modular Managed Switch. Note the Industrial Modular Managed Switch is configured through an Ethernet connection. Please make sure the manager PC must be set to the same IP subnet address. - Page 12 (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. PLANET Technology Corp. Made in Taiwan Figure 5-3: MAC ID Label 2.2 After logging in, you will be prompted to change the initial password to a permanent one.
- Page 13 3. Once the password change is complete, re-enter the web interface using your new password and the main screen appears as Figure 5-5 shows. Figure 5-5: Web Main Screen without Installed Expansion Cards Switch Menu Sub-menu Figure 5-6: Web Main Screen with Fully Installed Expansion Cards The Switch Menu on the top of the Web page lets you access all the commands and statistics the Industrial Modular Managed Switch provides.
- Page 14 Figure 5-8: Switch Sub-menu Figure 5-9: Switch Sub-menu Now, you can access the Web management interface to continue managing the switch. For more detailed information, please refer to the user manual. If you’re unfamiliar with any switch functions or parameters, click the “Help” icon on any Web page to view helpful descriptions.
-
Page 15: Saving Configuration Via Web
5.2 Saving Configuration via Web To save all applied changes and set the current configuration as a startup configuration, the startup-configuration file will be loaded automatically across a system reboot. 1. Click the Save icon on the top Switch Menu bar. 2. Press the “Save Configuration” button. 3. -
Page 16: Installing The Expansion Cards Into The Slots
6. Installing the Expansion Cards into the Slots There are two types of expansion cards available to enhance the switching capabilities of the Industrial Modular Managed Switch. They are: Model Name Description 4-Port 10/100/1000T Switch Module for IMS-6325-5 IMS-4T (-40~75 degrees C) 4-Port 100/1000X SFP Switch Module for IMS-6325-5 IMS-4S (-40~75 degrees C) You can install any combination of cards into the 5 available slots on the Industrial Modular Managed Switch based on your requirements. If not all 5 slots are used,... - Page 17 3. Carefully slide the expansion card into the guide slot and ensure it is fully inserted into place. 4. Tighten the thumbscrews to secure the expansion card, and then restore power to the switch. 5. Once the switch is powered on, the expansion cards will be automatically detected and ready for use.
-
Page 18: Restoring Default Configuration
192.168.0.xx using the default password. Please note that this action will erase all previous settings and restore the device to its factory default state. Alarm Ring R.O. Console 115200,N,8,1 Reset Max. Fault Alarm Loading: 24V, 1A DC Input: 12-48V , 5.5A max. Figure 7-1: IMS-6325-5 Reset Button... -
Page 19: Customer Support
8. Customer Support Thank you for choosing PLANET products. For troubleshooting, we recommend checking our online FAQ section on the PLANET website first. If you require further assistance, please don't hesitate to contact the PLANET switch support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq Switch support team mail address: support@planet.com.tw IMS-6325-5 User’s Manual: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword=IMS- 6325&view=3#list (Please select your switch model name from the Product Model drop-down menu.) Copyright © PLANET Technology Corp. 2024.
Need help?
Do you have a question about the IMS-6325-5 and is the answer not in the manual?
Questions and answers