Advertisement
IL - (847) 841-7867
INSTALLATION, SERVICE & PARTS MANUAL
IL - (847) 841-7867
Distributed by Pump Supply Inc
CP6NC
Illinois Location:
(847) 841-7867
860 Church Rd Elgin, IL 60123
Minnesota Location:
(651) 758-7867
330 Mill Bay South Suite 1511
Afton, MN 55001
PumpSupplyInc.com
9HP thru 60HP
Submersible Non-Clog
1150RPM, 60HZ
1750RPM, 60Hz
MN - (651) 758-7867
No: CP6NC - 04/15
1
MN - (651) 758-7867
Advertisement
Table of Contents
Related Manuals for Champion Pump CP6NC
Summary of Contents for Champion Pump CP6NC
- Page 1 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 CP6NC 9HP thru 60HP Submersible Non-Clog No: CP6NC - 04/15 INSTALLATION, SERVICE & PARTS MANUAL 1150RPM, 60HZ 1750RPM, 60Hz Illinois Location: (847) 841-7867 860 Church Rd Elgin, IL 60123...
-
Page 2: General Safety Information
Keep clear of suction property damage. Each Champion Pump is working on a used pump or piping. Never and discharge individually factory tested to insure proper enter a basin after it has been used. - Page 3 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Specifi cations DISCHARGE 6” 125 lb., Flange Horizontal LIQUID TEMPERATURE 104°F Continuous MOTOR HOUSING Cast Iron, Class 30 VOLUTE Cast Iron, Class 30 Single vane, enclosed type with pump out IMPELLER vanes on back side, Dynamically balanced, ISO G6.3, Cast Iron, Class 30...
-
Page 4: Specifications And Dimensions
IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Specifi cations & Dimensions NEMA FULL LOCKED CORD Volts/ CORD CORD MODEL START LOAD ROTOR O.D. SIZE TYPE CODE AMPS AMPS inch CP6NC9096 230/3 1150 26.0 162.0 6/3-3G 1.01 CP6NC9046... - Page 5 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Performance IL - (847) 841-7867 PumpSupplyInc.com MN - (651) 758-7867...
- Page 6 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Specifi cations & Dimensions NEMA FULL LOCKED CORD Volts/ CORD CORD MODEL START LOAD ROTOR O.D. SIZE TYPE CODE AMPS AMPS inch CP6NC18034 230/3 1750 50.6 232.0 6/3-3G 1.01 CP6NC18044...
- Page 7 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Performance Illinois Location: (847) 841-7867 860 Church Rd Elgin, IL 60123 Minnesota Location: (651) 758-7867 330 Mill Bay South Suite 1511 Afton, MN 55001 PumpSupplyInc.com IL - (847) 841-7867 PumpSupplyInc.com MN - (651) 758-7867...
- Page 8 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Performance Illinois Location: (847) 841-7867 860 Church Rd Elgin, IL 60123 Minnesota Location: (651) 758-7867 330 Mill Bay South Suite 1511 Afton, MN 55001 PumpSupplyInc.com IL - (847) 841-7867 MN - (651) 758-7867...
- Page 9 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Specifi cations DISCHARGE 6” 125 lb., Flange Horizontal LIQUID TEMPERATURE 104°F Continuous MOTOR HOUSING Cast Iron, Class 30 VOLUTE Cast Iron, Class 30 with Bronze wear ring 3 vane, enclosed type with pump out vanes on IMPELLER back side, Dynamically balanced, ISO G6.3, Cast...
- Page 10 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Specifi cations & Dimensions NEMA FULL LOCKED RO- CORD CORD CORD MODEL Volts/Ph START LOAD TOR AMPS SIZE TYPE O.D. CODE AMPS CP6NC30034H 230/3 1750 76.0 364.0 2/3-3G 1.34 CP6NC30044H...
- Page 11 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Performance Illinois Location: (847) 841-7867 860 Church Rd Elgin, IL 60123 Minnesota Location: (651) 758-7867 330 Mill Bay South Suite 1511 Afton, MN 55001 PumpSupplyInc.com IL - (847) 841-7867 PumpSupplyInc.com MN - (651) 758-7867...
-
Page 12: Receiving And Installation
IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Receiving & Installation Receiving Inspection Submergence Both a check valve and a shut-off valve are recommended for each pump. The Upon receiving the pump, it should be The pump should always be operated in check valve is used to prevent backflow inspected for damage or shortages. -
Page 13: Installation & Service
IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Installation & Service Overload Protection: Moisture Sensors - A normally open Pre-Operation Single Phase - The stator in-winding (N/O) sensor rated of 1 watt @330K Check Voltage and Phase - Compare overload protector used is referred to ohms, 500 volt, is installed in the pump the voltage and phase information... - Page 14 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Service Maintenance Oil Testing Pressure Test • Drain oil into a clean, dry container by Motor Housing - Oil should be at normal No lubrication or maintenance is required. placing pump on it’s side, remove cap level.
- Page 15 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Service Inspect seal for signs of uneven wear Apply adhesive compound to the shaft Cooling Oil pattern on stationary members, chips and and press bearing (13) onto shaft, position Recommended Supplier/Grade scratches on either seal face.
- Page 16 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Service Reassemble the diaphragm (23) with “bulg” facing seal plate (24). Place plate (44) on diaphragm (23) and insert capscrews (45) into plate and tighten. Place seal plate (24) over shaft onto bearing bracket (15), being careful not to damage outboard stationary member and align holes for cap screws (25).
- Page 17 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Service Remove gland nuts (36B) & (37B), friction rings (36C) & (37C), and grommets (36D) & (37D) from conduit box (4), inspect and replace if damaged (See Figure 4). Reassemble by inserting one friction ring, grommet, one more friction ring and gland nut into conduit box.
-
Page 18: Repair Parts
IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Repair Parts For Repair Part Please supply: Model Number and MFG Date as shown on Name Plate, and Part Description and Part Number as shown on Parts List. Figure 6 IL - (847) 841-7867 PumpSupplyInc.com... -
Page 19: Parts List
IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Parts List For Repair Part Please supply: Model Number and MFG Date as shown on Name Plate, and Part Description and Part Number as shown on Parts List. Ref. - Page 20 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Parts List For Repair Part Please supply: Model Number and MFG Date as shown on Name Plate, and Part Description and Part Number as shown on Parts List. Ref.
- Page 21 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Parts List For Repair Part Please supply: Model Number and MFG Date as shown on Name Plate, and Part Description and Part Number as shown on Parts List. Ref.
- Page 22 IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 Parts List For Repair Part Please supply: Model Number and MFG Date as shown on Name Plate, and Part Description and Part Number as shown on Parts List. Ref.
-
Page 23: Troubleshooting Chart
NOTE: Champion Pump assumes no responsibility for damage or injury due to disassembly in the fi eld. Disassembly of the pumps or supplied accessories other than at Champion Pump or its authorized service centers, automatically voids warranty. -
Page 24: Limited Warranty
IL - (847) 841-7867 Distributed by Pump Supply Inc MN - (651) 758-7867 LIMITED WARRANTY Manufacturer warrants, to the immediate purchaser and subsequent initial owner during the warranty period, every new pump to be free from defects in material and workmanship under normal use and service, when properly used and maintained, for a period of eighteen (18) months from date of manufacture or twelve (12) months from date of installation (which ever comes fi rst). - Page 25 Start-Up Report / Warranty Registration Please fill out the following questions as completely and accurate as possible. Please mail to Champion Pump Company, Inc. – P. O. Box 528 – Ashland, OH 44805. REPORTS THAT ARE NOT RETURNED CAN DELAY OR VOID WARRANTY.
Need help?
Do you have a question about the CP6NC and is the answer not in the manual?
Questions and answers