Download
Share
Print this page
  1. Manuals
  2. Brands
  3. ADVANCED SIMRACING Manuals
  4. Chassis
  5. ASR1
  6. Assembly and user's manual

ADVANCED SIMRACING ASR1 Assembly And User's Manual

Hide thumbs Also See for ASR1:

Advertisement

Quick Links

Download this manual
ASR1 Chassis – Gen 2
ASSEMBLY AND USER GUIDE

Advertisement

loading
Need help?

Need help?

Do you have a question about the ASR1 and is the answer not in the manual?

Questions and answers

Related Manuals for ADVANCED SIMRACING ASR1

Summary of Contents for ADVANCED SIMRACING ASR1

  • Page 1 ASR1 Chassis – Gen 2 ASSEMBLY AND USER GUIDE...

  • Page 2: Table Of Contents

    Table of Contents Disclaimer ............................... 3 Required Tools ............................1 Content of packages .......................... 2 Main Content ............................ 2 Pedal Tray Components ......................3 Wheel Deck Components ......................3 Assembly guide ............................. 4 Main Chassis ............................ 4 T-Nut install tip ..........................16 Corner gusset tip .........................

  • Page 3: Disclaimer

    Disclaimer This assembly guide shall be considered as such: a guide. The steps, methods and measurements are suggestions from our assembly experience and are in no way shape or form absolute. The dimensions shown throughout the guides are reference dimensions. They are subject to be revised without notice and can be altered for preferred position of your peripherals.

  • Page 5: Required Tools

    Required Tools 6mm Allen key 5mm Allen Key Flathead screwdriver Tape Measure For questions, issues or comments, feel free to reach our support team! https://www.advancedsimracing.com/pages/advanced-help-center...

  • Page 6: Content Of Packages

    Content of packages Boxes 1X ASR1 box Main Content M8 X 35 Corner Gusset & Cover Hex screws – 4X 8X each M8 T-Nuts – 40X M8 X 16 Hex screws – 40X Up-post upper and lower fixing plates 2X each 26”...

  • Page 7: Pedal Tray Components

    Pedal Tray Components Pedal tray side bracket – 2X Wheel Deck Components M8 X 16 Flat Head Deck to Up Post plate Deck to Up Post plate Screw - 8X Right – 1X Left – 1X Standard Wheel Deck Standard Mount – 1X...

  • Page 8: Assembly Guide

    Assembly guide Main Chassis Assemble 4 X corner gussets with 2 M8 screws and 2 M8 T-Nuts. Screw in the T-Nuts no more than ½ a turn. Make sure to respect the shown orientation of the T-Nuts for trouble-free assembly. Slide the gussets on either side of the 19”...
  • Page 9 Measure 22” as shown and tighten fully. You can cap up the Corner gussets. Assemble the lower up-post plate with 2X M8x16 socket screws and 2X m8 t- nuts. Repeat twice. Slide the assembled plates through the 50” extrusion as shown below. Place them at 17in from the front, do not tighten yet.
  • Page 10 Loosely assemble the rubber feet with the M6 X 20 screw and M6 T-Nut. Slide the rubber feet through the same side as the previously placed lower brackets on the 50” Extrusions. Tighten fully. Prepare the upper up-post brackets with 4X M4 x 16 socket screws and 4X M8 t-nuts each.
  • Page 11 Slide the up-post brackets on the 3” x 26” extrusions. Do not tighten, repeat twice. Slide the up-posts in position. Guide the loose t-nuts through the top of the extrusion and place the assembly over the previously placed lower bracket.
  • Page 12 Place the up-posts at 17” from the front. Secure the bottom part of the up-posts with 2x M8 x 16 socket screws. Tighten fully all 4 bottom screws as well as both corner brackets up top.
  • Page 13 Place 4x M8 t-nuts following the pattern shown below. Use the trick at the page “T-nut install tip” to facilitate the step! Install the pre-drilled 1.5” X 22” extrusion with the faces towards the outside and the larger hole towards the top. Use 4X M8 x 35 socket screws through the previously placed t-nuts.
  • Page 14 Assemble the pedal tray with the 2 pedal tray side brackets, 2x 3x18.5” extrusions and 4x M8x16 socket screws. Place 4X M8x16 socket screws and 4X M8 t-nuts to the vertical slots on the pedal tray. Tighten no more than a turn.
  • Page 15 Slide the t-nuts of the pedal tray through the inside slot of the 50” extrusion. Tighten it snug for the moment, but only fully tighten after positioning your pedals. (See User guide section for details)
  • Page 16 19. Assemble the wheeldeck: 19.1. Assemble the side plate to the 3” X 6 7/8” extrusion using 2X M8 X 16 flat head screws. Repeat for both sides, tighten fully. Make sure the flat face is facing downwards. 19.2. Install the end caps in the middle using 2 pushpins each. Press hard to ensure no vibration from the caps.
  • Page 17 Prepare the Wheel Deck with 4X T-Nuts and 4X M8 X 16 socket screws. Screw in the T-Nuts no more than a turn. Slide the Wheel Deck through the top of the Up Post Channels. Fully tighten. (For the Fanatec side mount option, simply install one side at a time, install your wheel, and then adjust height with the wheelbase in place) If the Wheel Deck seems too large for the gap, loosen further the two bottom plates and corner plates holding the Up Posts.
  • Page 18 For the finishing touches, cap all the visible open extrusion ends using the corresponding endcap and pushpins. Install also any remaining corner gusset caps.
  • Page 19 Congratulations on your new ASR1 Simracing Chassis!

  • Page 20: T-Nut Install Tip

    T-Nut install tip Insert an M8 T-Nut in the desired slot of the extrusion. Insert the T nut perpendicular, and with the help of a small allen key in your attire such as a 3mm, pry the T nut straight with the allen key through the hole. The t-nut will snap into place when in position.

  • Page 21: Corner Gusset Tip

    Corner gusset tip Installing a corner gusset to a flat surface or perpendicular to the extrusion is not possible with the locating tabs in place. Fear not, they are made to be broken off with the following method. Using a flathead screwdriver, slide the flathead under the small tab on the bottom, and pry out the tab.

  • Page 22: User Guide

    User Guide Pedal tray adjustment You can position the T-nut/screw assembly however high or low. Make sure to have your pedals already properly setup before placing the pedal tray! Tighten fully the 4 screws holding the pedal tray before use, you may want to verify a second time just to be sure.

  • Page 23: Entry Level Pedal Installation

    Entry level pedal installation Pedals such as the T3PA from Thrustmaster or the G29 pedals from Logitech cannot be installed from the top, fastened with t-nuts. You will need to use the included corner gussets and position the gussets and 1.5” extrusions of the pedal plate to line up with the bolt pattern.

  • Page 24: Wheel Deck Adjustment

    Wheel deck adjustment The standard wheel deck can be adjusted using the Up Post brackets. With your wheel installed, loosen 3 out of the 4 screws and place yourself in the rig. Slowly loosen the last screw until you feel the wheel deck moving. It will most probably drop with the weight of the wheel so be careful! You can then place the wheel according to your preference in height and angle and tighten when the position is satisfactory.